OTS IES8222MPp9H-S-DR User manual

OT Systems Ltd. | www.ot-systems.com
Quick Installation Guide
IES8222MPp9H-S-DR / version 1.1
Quick Installation Guide
IES8222MPp9H-S-DR
Description: L2+ Hardened Grade Managed 8-port 10/100/1000Base-TX (PoE++) + 2-port
100/1000Base-SFP Ethernet Switch
Overview: IES8222MPp9H-S-DR is a new generation, managed, industrial grade, L2+ Gigabit PoE++
(Power over Ethernet plus plus) switch that provides 8x10/100/1000Base-TX RJ45 ports
plus 2x100/1000Base-SFP ports. It provides stable and reliable Ethernet transmission
with high quality design and reliability.
Package Content
⚫Managed PoE Switch x 1
⚫DIN-Rail Clip x 1
⚫RJ-45 Console Cable x 1
⚫Quick Installation Guide x 1
Read Before Install
◎Keep power off during installation
◎use Antistatic Wrist Strap correctly
◎Make sure using correct power supply, voltage must match
◎Make sure enough power supply from PSU that will not overload
◎Double check the wiring ( +/- ) is correct.
◎Keep installation dry and clean.

OT Systems Ltd. | www.ot-systems.com
Quick Installation Guide
IES8222MPp9H-S-DR / version 1.1
◎Do not open the chassis
DIN Rail Installation
DIN rail. Installation methods are as follows:
Power Input
The Industrial Switch has two redundant power inputs, PRW1 and PWR2. The Phoenix terminal
patch panel connector is located on the top panel of the switch. The front view of the patch panel is
shown below.
PoE Output
IEEE 802.3bt, per port 90W, 1/2(+), 3/6(-); 4/5(+), 7/8(-)
Setup and States
a) Connect the Ethernet port of the media converter to a PoE IP camera (PoE device) or network
device with a network cable.
b) Insert the appropriate SFP into the SFP port. Connect the fiber cable from the device (media
converter or switch) on the other end to the LC connector of the SFP.
1
2

OT Systems Ltd. | www.ot-systems.com
Quick Installation Guide
IES8222MPp9H-S-DR / version 1.1
c) After the device is powered on, the PWR indicator will all be on. If the indicators are not on,
check the power supply connection.
d) After all cables are correctly connected, the indicators will be lit as per port status LEDs.
e) LED
Indicators
Description
PWR (P1&P2)
ON
POWER ON
OFF
NO POWER
RUN
Blink
Transmitting or receiving data
LINK/ACT (1-12)
ON
Connected
Blink
Transmitting or receiving data
OFF
Disconnected
ALM
ON
Has alarm information
OFF
No alarm information
Introduction to DIP switches
DIP Switch
State
Description
#1
ON
RSTP Disable
OFF
RSTP Enable (Default)
#2
ON
Port VLAN Enable
OFF
Port VLAN Disable (Default)
#3
ON
SFP port is 100M
OFF
SFP port 100/1000M (Default)
#4
Function Reserve
Notes:
1. RSTP switches to the ON position, which indicates RSTP is in disabled status.
2. VLAN switches to the ON position, which indicates VLAN is in enabled status. All LAN ports are
only able to communicate with the SFP uplinks when this option is enabled.
3. To take effect the DIP Switch function while the ethernet switch is in operation, there is a need
to reboot the Ethernet switch after tuning the DIP switch.
General
To ensure trouble free transportation and storage, all OT Systems products must be thoroughly
inspected, tested and properly packed before delivery. Check the product upon receipt for any
visible damage which may have been caused during shipment.
-END-