Planet IGS-6325-8T4X User manual

Industrial L3 Multi-Port Gigabit
Managed Ethernet Switch
IGS-6325 DIN-rail Series
Quick Installation Guide

Table of Contents
1. Package Contents ....................................................................................... 3
2. Requirements ............................................................................................. 5
3. Wiring the Power Inputs.............................................................................. 6
3.1 Grounding the Device .......................................................................... 8
4. Terminal Setup ........................................................................................... 9
4.1 Logging on to the Console...................................................................10
 4.2 ConguringIPAddressviaConsole ......................................................11
 4.3 StoringCurrentSwitchConguration....................................................12
5. Starting Web Management .........................................................................13
5.1 Logging in to the Industrial Managed Switch.........................................13
 5.2 SavingCongurationviaWeb ..............................................................15
6. RecoveringBacktoDefaultConguration.....................................................17
7. Customer Support .....................................................................................19

3
1. Package Contents
Thankyouforpurchasing PLANETL3Industrial ManagedSwitch,IGS-6325 DIN-rail
series. The descriptions of these models are as follows:
IGS-6325-16P4S IndustrialL316-Port10/100/1000T802.3atPoE+4-Port
1G/2.5GSFPManagedEthernetSwitch
IGS-6325-16T4S IndustrialL316-Port10/100/1000T+4-Port1G/2.5G
SFPManagedEthernetSwitch
IGS-6325-8T4X IndustrialL38-Port10/100/1000T+4-Port10GSFP+
ManagedEthernetSwitch
IGS-6325-8T8S IndustrialL38-Port10/100/1000T+8-Port1G/2.5GSFP
ManagedEthernetSwitch
IGS-6325-8T8S4X IndustrialL38-Port10/100/1000T+8-Port1G/2.5GSFP+
4-Port10GSFP+ManagedEthernetSwitch
IGS-6325-8UP2S IndustrialL38-Port10/100/1000T802.3btPoE+2-Port
1G/2.5GSFP+ManagedEthernetSwitc
IGS-6325-8UP2S2X
IndustrialL38-Port10/100/1000T802.3btPoE+2-Port
1G/2.5GSFP+2-Port10GSFP+ManagedEthernet
Switch
“Industrial Managed Switch” mentioned in this Quick Installation Guide refers
to the above models.

4
Open the box of the Industrial Managed Switch and carefully unpack it. The
box should contain the following items:
The
Industrial
Managed
Switch
DB9 to RJ45
Interface
RS232
Console
Cable
Quick
Installation
Guide
Wall
Mounting
Kit
RJ45
Dust
Cap
SFP
Dust
Cap
IGS-6325-16P4S    
17 4
IGS-6325-16T4S    
IGS-6325-8T4X     9 4
IGS-6325-8T8S     9 8
IGS-6325-8T8S4X     912
IGS-6325-8UP2S     9 2
IGS-6325-8UP2S2X     9 4
Ifanyof theseare missingor damaged,please contactyourdealer immediately.If
possible, retain the carton including the original packing materials to enable you to
repack the product in case there is a need to return it to us for repair.

5
2. Requirements
The Industrial Managed Switch provides remote login interface for management
purposes. The following equipment is necessary for further management:
zWorkstationsrunningWindows XP/2003/2008/Vista/7/8/10,MACOS X orlater,
Linux,UNIX,orotherplatformsarecompatiblewithTCP/IPProtocols.
zWorkstationsareinstalledwithEthernetNIC(NetworkInterfaceCard).
zSerialPortConnection(Terminal)
The above Workstations come with COM Port (DB9) or USB-to-RS232
converter.
The above Workstations have been installed with terminal emulator,suchas
HyperTerminalincludedinWindowsXP/2003,puttyorteraterm.
Serial cable -- one end is attached to the RS232 serial port, while the other
end to the console port of the Industrial Managed Switch.
zEthernetPortConnection
Network cables--Usestandardnetwork(UTP)cableswithRJ45connectors.
The above PC is installed with Web browser.
Note
It is recommended to use Internet Explorer 8.0 or above to access
the Industrial Managed Switch.

6
3. Wiring the Power Inputs
The Upper Panel of the Industrial Managed Switch indicates an inlet power
socket and consists of one green terminal block connector within 6 contacts. Please
follow the steps below to insert the power wire.
1.Insert positive/negative DC power wires into Contacts 1 and 2 for Power 1, or
Contacts 5 and 6 for Power 2.
IGS-6325-16P4S:DC48-56V
DI 0DI 1DO 0DO 1GND GND
Fault
V1+ V2+1A@24V
DC2DC1
Dual power input is required
for maximum PoE loading.
Refer to user’s manual for
more details.
Input: 48-56V , 7.5A max.
1 2 3 4 5 6
1 2 3 4 5 6
Figure 3-1: IGS-6325-16P4S Upper Panel
IGS-6325-16T4S:DC9-48V,AC24V
DI1 DO0 DO1DI0 GNDGND
Max. fault loading: 24V, 1A
DC Input: 9-48V , 3.3A max.
AC Input: 24V
, 1.2A max.
V1+ V2+
PWR1 PWR2Fault
1 2 3 4 5 6
1 2 3 4 5 6
Figure 3-2: IGS-6325-16T4S Upper Panel

7
IGS-6325-8T4X/IGS-6325-8T8S/IGS-6325-8T8S4X:DC12~48V,AC24V
DI1 DO0 DO1DI0 GNDGND
Max. fault loading: 24V, 1A
V1+ V2+
PWR1 PWR2Fault
DC Input: 12-48V , 4A max.
AC Input: 24V , 2A max.
1 2 3 4 5 6
1 2 3 4 5 6
Figure 3-3: IGS-6325-8T4X/IGS-6325-8T8S/IGS-6325-8T8S4X Upper Panel
IGS-6325-8UP2S/IGS-6325-8UP2S2X:DC48~56V
PWR1 PWR2
Fault
DI1 DO0 DO1DI0 GNDGND
DC Input:
48-56V , 7.5A max.
Max. fault loading: 24V, 1A
Dual power input is required
for maximum PoE loading.
Refer to user’s manual for
more details.
1 2 3 4 5 6
1 2 3 4 5 6
Figure 3-4: IGS-6325-8UP2S/IGS-6325-8UP2S2X Upper Panel

8
2.Tightenthewire-clampscrewsforpreventingthewiresfromloosening.
123456
V+ V- V+ V-
Power 1 Power 2
Figure 3-5: The pin of 6-contact terminal block connector
Note
1. The wire gauge for the terminal block should be in the range
from 12 to 24 AWG.
2.Please check the wire AWG Ampere specification before
connectingPLANETIndustrialManagedSwitch.
3.1 Grounding the Device
Users MUST complete grounding wired with the device; otherwise, a sudden
lightning could cause fatal damage to the device.
DI 0DI 1DO 0DO 1GND GND
Fault
V1+ V2+1A@24V
DC2DC1
Dual power input is required
for maximum PoE loading.
Refer to user’s manual for
more details.
Input: 48-56V , 7.5A max.
1 2 3 4 5 6
1 2 3 4 5 6
Earth Ground

9
4. Terminal Setup
To congure the system, connect a serial cable to a COM port on a PC or
notebook computer and to RJ45 type serial (console) port of the Industrial
Managed Switch.
PC/Workstation with
Terminal Emulation Software
RJ45 to DB9 RS232 Cable
Serial Port
Console Port
115200,N,8,1
IGS Industrial Managed Switch
Console
115200,N,8,1
A terminal program is required to make the software connected to the Industrial
Managed Switch.
1. Run terminal program on the OS.
2.When the following screen appears, make sure that the COM port should be
conguredas:
Baud: 115200
Parity:None
Data bits: 8
Stop bits: 1
Flowcontrol:None

10
4.1 Logging on to the Console
Once the terminal has been connected to the device, power on the Industrial
Managed Switch and the terminal will display “running testing procedures”.
Note
The following console screen is based on the IGS-6325-16P4S.
The display of the IGS-6325 series is the same as that of the IGS-
6325-16P4S.
Then, the following message asks to log in user name and password. The factory
defaultusernameandpasswordare shownasfollowsastheloginscreen inFigure
4-1appears
UserName:admin
Password: admin
Figure 4-1: Console Login Screen
The user can now enter commands to manage the Industrial Managed Switch. For
adetaileddescriptionofthecommands,pleaserefertothefollowingchapters.
Note
1.For security reason, please change and memorize the new
password after this first setup.
2. Only accept command in lowercase letter under console inter-
face.