LED Desk Lamp with Charging Station
CSA77WGC CSA77WGC-SHPR ACDL10P
CONGRATULATIONS!
You’ve purchased the finest in natural lighting technology with
your new OttLite®product.
PRODUCT REGISTRATION FORM
Please complete the enclosed Product Registration Form and
return it today by mail, or register online by going to:
OttLite.com/warranty.
NOTE: THIS UNIT IS FULLY ASSEMBLED
1. Remove lamp from packing placing lamp body base (A) flat
on a steady surface.
2. Connect the AC Adapter input (E) into connector (F) in the
rear-bottom of the lamp.
3. Plug the A/C adapter (D) into a standard household 120V AC
outlet. Note: Only use with the supplied AC adapter to
avoid damage or fire.
4. Turn the lamp ON & OFF using power switch (B) located
in the front-upper side of base (A). Power switch (B) is a
“touch” switch that controls the dimmer function for 3 levels
of brightness.
5. To power LED settings, slightly touch the switch to achieve
the following:
• turn lamp “ON” to rst lower-brightness; touch the
switch “once”;
• for medium-brightness; touch the switch “twice”;
• for high-brightness; touch the switch “three-times”;
• to turn lamp “OFF”; touch the switch “four-times”.
6. To position the shade simply bend the flex-neck (G) as
needed to point the light. Please hold the lamp base (A)
while adjusting the lamp. Take care not to overextend the
lamp to avoid unbalancing it and damage. Please refer to
diagrams for lamp maximum adjustment range.
SAFETY WARNING: TO REDUCE THE RISK
OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS
1. Turn lamp off and WAIT UNTIL LAMP HEAD (C) is COOL
before handling.
2. Touch plug only when turning ON or OFF.
3. The LED panel (L) might get hot after several hours of
continuous use, DO NOT place your hands directly on
LED light panel.
4. Never use with an extension cord unless the plug can be
fully inserted into the receptacles in the extension cord.
5. Do not alter the plug.
6. The lamp head included with this unit cannot be replaced by
the consumer.
7. INDOOR USE ONLY
NOTE: The important safety instructions appearing in this
instruction sheet are not meant to cover all possible conditions
and situations that may occur. It must be understood that
common sense, caution, and care must be used with any
electrical product.
CAUTION! IF THE ExTERNaL FLExIbLE CabLE OR
CORD OF THIS LUmINaIRE IS DamagED, IT SHaLL bE ExCLUSIvELY
REPLaCED bY THE maNUFaCTURER OR ITS SERvICE agENT OR a
SImILaR qUaLIFIED PERSON IN ORDER TO avOID a HazaRD.
CAUTION! THE LIgHT SOURCE OF THIS LUmINaIRE IS
NOT REPLaCEabLE; WHEN THE LIgHT SOURCE REaCHES ITS END OF
LIFE THE WHOLE LUmINaIRE SHaLL bE REPLaCED.
FCC PART 15
Note: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part
15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that the
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different
from that of the receiver.
• Consult the dealer or an experienced radio/TV technician
for help.
Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to
operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation
CAUTION: Any change or modification to product not
expressly recognized by OttLite Technologies voids OttLite’s
responsibility for proper function of product.
CAN ICES-005 (B)/NMB-005 (B)
AC/DC ADAPTER
Input: AC 100-240V, 50/60 Hz, 0.6A
Output: 5V DC, 3.0A with a Male DC Plug
THIS LAMP CONTAINS a 5V-2.1A USB output port (H) located on
the base of the lamp. USB port can charge such items as tablets,
cellular phones, etc.
English LED Desk Lamp with Charging Station
INS190469 REV040919
30° 30°
*Lamp cannot be used
in this position
120°
45° 45°
L
C
G
B
A
E
F
D
H
Vertical Direction
-60°~60°
