OUMAN Ouflex A User manual
YM0008A: Versio 2.9->
USER MANUAL
YM0008C: Versio 2.11->
OUFLEX
Compact freely programmable automation unit
• Application and user interface are freely
• DIN rail-mounted module casing (12M)
• Detachable strip connectors make installation
easier
Web
UI
Use of a GSM phone
requires that the GSM modem (optional) is con-
nected to the controller.
message using key words.
the Web UI can be done through LAN or internet. With
remote controll you can use the device regardless of
place and time.
Properties of the Web UI:
- easy-to-use drawing tool
- SMS alarm routing
- trends
Note! Ounet and Web UI can be used simultaneously.
Key words:
Active alarms
Alarm history
KEY WORDS
OUFLEX A
OUFLEX A XL
2
-
OK
OK
OK
-
-
to navigate in the menu.
Press the control knob
to enter the menu and
accept the changes.
menu. Holding the key down for a few seconds of time returns the
background light dims and the keyboard locks if the locking func-
tion is in use.
-
3
1 System settings .............................................................................................................................................................. 4
1.3 Network settings .................................................................................................................................................... 6
1.3.1 IP settings .......................................................................................................................................................... 6
1.8 Do backup and restore factory settings .............................................................................................................. 10
2 Alarms............................................................................................................................................................................11
3 Point information ......................................................................................................................................................13
3.1 Wiring info ........................................................................................................................................................... 13
3.1.1 Measuring point control/ manual control ..........................................................................................................13
3.3.1 Present value .................................................................................................................................................... 14
3.3.2 Weekly schedule .............................................................................................................................................. 15
3.3.3 Special days .................................................................................................................................................... 16
5 Naming .........................................................................................................................................................................18
8 Web UI .........................................................................................................................................................................22
8.4 Point info .................................................................................................................................................................31
8.5 System settings ........................................................................................................................................................31
8.6 Device mangement ...............................................................................................................................................31
4
history.
Time 17:01
Date 05.04.2023
Language English/English
Daylight saving On
>
>
>
>
Time
19:44
hh:mm
Enter the hours
It is important that time and the date are correct. Alarm informa-
-
vated. It is highly recommendable to ensure that time and date are
correct when you are making time programs with the weekly pro-
clock takes daylight savings
for power outages lut for a couple of days.
Hours and minutes can be set separately.
1. Set hours and press OK to accept.
2. Set minutes and press OK to accept.
3.
System settings
1. Enter your SIM card PIN code.
2.
3. Connect the
(15 Vdc/650 mA)
4.
not visible on the display).
5.
6. Enter Device ID (optional).
-
-
tion fails to verify that the message center number has not been manually entered. Press and hold ok
-
-
-
nication.
Date
Wed 05.04.2023
dd.mm.yyyy
Enter the day: 1. Set day and press OK to accept (name of weekday is updated
automatically).
2. Set month and press OK to accept.
3. Set year and press OK to accept.
4.
Daylight saving
On
Off
Youcanhide/showthissettingbypressingOKforafewseconds.
into summer and winter time.
You can change the HMI language here if device has more than
one language.
Language
Suomi/Finnish
English/ English
Svenska/ Swedish
5
Device ID
0
O U 0 1
-
-
the keyword.)
-
correctly installed and the subscription agreement is valid.
Approve: Press OK a number of seconds
Cancel: Press ESC a number of seconds
1.
2.
.
When connect modem supply to
automatically.
-
device.
SIM card holder pops out. Pull out the SIM card holder. Do not try to re-
move the SIM card holder without pressing the SIM card release button
device. Make sure the PIN inquiry is in use in the SIM card.
You can check the status of the modem also on the modemLED indicator light.
SIM card slot
SIM card release button
Antenna
mounting
point
ESC
93
1
2
6
1.
2.
-
tings manually you need to ask correct settings in that LAN ad-
-
3.
IP settings
DHCP Off >
Gateway adress 0.0.0.0 >
Subnet mask 0.0.0.0 >
IP address 0.0.0.0 >
Nameserver address 0.0.0.0 >
Update network settings >
1.
2.
3.
-
cessful. Either the settings used previously or factory settings
-
-
service is in use.
4.
the device now functions in the network. Device IP address is
shown on display.
network settings:
have been connected.
2. Network settings are set manually.
Network settings
IP-address x.x.x.x >
Hostname
Connection status Ofine >
IP settings >
Time settings >
Access settings >
Modbus TCP/IP >
SNMP >
.
the controller displays the network mode OUMAN Access.
-
•
•
•
1.
2. -
formation from administrator).
-
address to 10.200.1.1
Time settings
Time zone 2 >
Daylight saving On >
NTP server time.google.com >
NTP server 2 time1.google.com >
Access settings
Access Off >
Access name
Connection satus Ouman Access
-
-
-
son feeds in the target and billing information to the Ouman system and
-
-
•
-
•
•
•
8
Modbus TCP/IP
Modbus TCP port (internal registers) 5 0 2 >
Max connections 5 >
Idle timeout 0 >
Function active On >
Modbus TCP_IP_Gateway >
Connection address OuexAXL>
SNMP
IP address >
Functon active On >
Recommendation is that the val-
ues should not be changed unless there is a compelling reason.
-
-
RJ45
-
-
Modbus TCP/IP gateway
Modbus RTU master 1 (A1, B1) 504 >
Modbus RTU master 2 (A2,B2) 505 >
Modbus RTU master 3 (RJ45) 503 >
Modbus RTU master 1 (A1,B1)
Approve: Press OK for a number of seconds
Cancel: Press ESC for a number of seconds
00 5 0 4
-
Display settings
Display version xxxxx
Contrast 75 >
Type information
Serial number xxxxxxx
Application version x.x.x.
Ouman O uex x.x. x.
Display x.x.x
Platform SW x.x.x
Lock code
Display settings >
Type information >
Connections, meas. and states >
Lock code Not in use >
Lock code
In use
Not in use
>
-
Modbus RTU master 1 (COM2 (A1/B1))
A1/ B1
Baudrate 960 0 >
Data bits 8 >
Stop bits 1 >
Parity None >
Delay between packages 10 ms>
Modbus RTU slave (COM3 (A2/B2))
A2/ B2
Address 1 >
Baudrate 960 0 >
Data bits 8 >
Stop bits 1 >
Parity None >
Modbus RTU master 3 (COM1 (RJ45 7:8))
RJ45 7:8
Baudrate 1920 0 >
Data bits 8 >
Stop bits 1 >
Parity None >
Delay between packages 1 ms >
-
Modbus RTU master 3 (COM1 (RJ45 1:2))
RJ45 1:2
Baudrate 1920 0 >
Data bits 8 >
Stop bits 1 >
Parity Non
-
10
-
System settings
System settings
Restore application settings >
RRestore backup
>
Do backup
>
Log
>
Restore application settings >
RRestore backup
>
Do backup
>
Log >
System settings
Restore factory settings >
RRestore backup
>
Do baciup
>
Log >
-
Give lock code
0 0 0 0
Approve: Press OK for a number of seconds
Cancel: Press ESC for a number of seconds
Trend log 28.01 08:26:19 [ 34.7 °C ] ( s )
38
28
11
Conrm
Conrm
Empty alarm history
Yes No
Acknowledge all alarms
Yes No
thelast alarms.Messageisinformational.
Alarm history
02.11.2021 10:11:42 Sensor fault H1 Supply w
02.12.2021 11:22:40 Sensor fault H2 Return w
>
>
2
ALARM HISTORY
Deviation alarm
PR 1 GROUP 1
H1 Supply water temp. =10.2 °C
Received: 28.09.2022 02:27
Press OK to acknowledge the alarm
allactivealarms.Messageisinformational.
Alarms
Active alarms
Alarm history
Acknowledge all alarms
Reset alarm history
Routing schedule
Alarm receivers
Alarm signal
Alarm params
>
>
>
>
>
>
On
>
>
Active alarms
26.09.2022 12:24:52 H2 Risk of freeze
28.09.2022 01:12:40 Sensor fault H1 Return
>
>
2
2
•
has been silenced by pressing Esc.
•
•
alarm group it belongs to (1...10)
• What location the alarm is coming from
•
ACTIVE ALARMS
-
-
-
-
-
-
-
12
Editing view
Time Mode
Time Mode
Time Mode
M T W T F S S
M T W T F S S
M T W T F S S
OK
1.
delete and press OK.
2.
3. Press OK at the end of the row.
4.
1. Set switch time
2.Set alarm team 3.Select day(s)
Time Mode
08:00 Team 1
21:00 Delete switch time
00:00 Add new
M T W T F S S
OK
whichalarmteams alarms are routed at these times on the chosen
days.
1.
2. Press OK. Set the switch time for alarm routing (set hours and
minutes separately) and press OK.
3. Press OK and then turn the control knob to set the alarm team
alarms will not be forwarded.) Accept by pressing OK.
4. Press OK at each weekday you wish to choose.
5. Press OK at the end of the row to accept the new time pro-
gram.
6.
1.
and press OK.
2. -
es. Press OK to accept.
3. Press the OK button to change the day of the week.
4.
Graph
This example shows that group 1 alarms are al-
ways forwarded. During business hours (Mon-
day - Friday 8:00 a.m. - 4:00 p.m.) alarms
are forwarded to dierent teams than dur-
ing evenings and weekends. More detailed in-
formation is shown in the ”Editing view”.
Monday
>
Tuesday
>
Wednesda
>
Thursday
>
Friday
>
Saturday
>
Sunday
>
0 3 6 9 12 15 18 21 24
Group 1 Weekly schedule
08:00 Team 1
16:00 Team 2
00:00 Add new
08:00 Team 1
16:00 Team 2
00:00 Add new
08:00 Team 1
16:00 No routing
00:00 Add new
Routing schedule
Group 1 Weekly schedule
Group 1 Alarm routing now Team 1
Group 2 Weekly schedule
Group 2 Alarm routing now Team 1
>
>
>
>
13
Phone number 1
Approve: Press OK for a number of seconds
Cancel: Press ESC for a number of seconds
+3 5 8 4 0 8 4 0 0 0 0
Team 1
Phone number 1 >
Phone number 2 >
Phone number 3 >
Phone number 4 >
Alarm receivers
Team 1 >
Team 2 >
Team 3 >
-
OK
Alarm signal
OnPois
OFF
Phone number 1
Approve: Press OK for a number of seconds
Cancel: Press ESC for a number of seconds
3 5 8 4 0 8 4 0 0 0 0
Point info
Wiring info >
Bus points >
Time programs >
Wiring info
INPUTS:
UI 1 -10.3 °C >
UI 2 23.5 °C >
UI 3 Off >
Press
AO 1
Automatic
Manual control
AO 1
Automatic
Manual control AO 1
0 %
min:0 max:100
-
UI 1
NameU Outdoor temp. >1:UI
Point ID 2TK1.2TK1. UI2.M.M
Device type NTC10>
Trend log Off >
Alarm signal
Noresponse alarms >
System error! Off>
14
Bus points
Modbus RTU 1 (RJ45) >
Modbus RTU 2 (A1,B1) >
Modbus RTU 3 (A2,B2)
Modbus TCP Master
Modbus RTU 1 (RJ45)
FLEX COMBI 32 >
FLEX UI 12 >
Flex Combi 32
Device information >
Device information
Device state >
Address 1 >
Update device >
IO SW x.x
Device information
Device state >
Address 1 >
Ok messages 0
Timeouts 0
CRC errors 0
Error messages 0
Device state
Active
Passive
Error
Updating
Device type error
-
Time programs
H1 Heating temperature drop Off >
H2 Heating temperature drop Off >
Light control On >
El. group 1 control On >
Heating H1 Temperature drop
Present value Off >
weekly schedule >
Exception schedule >
Special days >
Heating H1 Temperature drop
-
-
-
-
-
Present value Off
Weekly schedule >
Exception schedule >
Special days >
15
0 3 6 9 12 15 18 21 24
Time
21:00 Temp. drop
06:00 Delete switch time
00:00 Add new
M T W T F S S
OK
Heating weekly/24-hour program
Monday >
Tuesday >
Wednesday>
Thursday >
Friday >
Saturday >
Sunday >
0 3 6 9 12 15 18 21 24
Time
06:00 Normal temp.
17:00 Temp. drop
00:00 Add new
M T W T F S S
OK
Time State
05:00 On
07:00 Off
00:00 Add new
M T W T F S S
OK
Weekly/24-hour program
Monday >
Tuesday >
Wednesday>
Thursday >
Friday >
Saturday >
Sunday >
-
-
Graph
Graph
Editing view
Editing view
1.
delete and press OK.
2.
3. Press OK at the end of the row.
In this example, you can see a weekly tempera-
ture drop program. Temperature drop is on from
5 pm to 6 am from Monday to Friday.
the states into which the function is driven at these times on the
chosen days.
-
ply press the OK button on the corresponding day of the week.
-
add new switch time values as needed.
1.
2. PressOK.Settheswitchtime(sethoursandminutesseparately).
Press OK to accept.
3. Press OK and then turn the control knob to set the control
state (temperature drop weekly program) or ON/OFF state
(electric controls). Press OK to accept.
4. Press OK at each weekday you wish to choose.
5. Press OK at the end of the row to accept the new time pro-
to automatic (=normal).
1.
and press OK.
2.
changes. Press OK to accept.
3. Press the OK button to change the day of the week.
4.
In this example, you can see a weekly car heating
program. According to the program, car heating
is on from 5 am to 7 am on working days.
16
Editing view
Graph
Time Mode
Time Mode
00:00 Add new
18:00 On
22:00 Off
00:00 Add newi
Relay 3 Special days
0 3 6 9 12 15 18 21 24
SD 1 >
SD 2 >
SD 3 >
Relay 3 Special days
0 3 6 9 12 15 18 21 24
SD 1 >
SD 2 >
SD 3 >
OK
0 6 12 18 24
0 6 12 18 24
-
In the example of relay 3 control has been
done the exception schedule. Relay 3 is swit-
ched o (OFF) 21.12.2022 11:30 - 03.01.2023
16:00.
Add/change switch time
Day: 21.12.2022Time:
11:30
Mode: Off
Repeat: No
Accept: Ready
Date Time
21.12.2022 11:30 Off >
03.01.2023 16:00 Automatic >
00.00.0000 00:00 Add new >
Date Time Mode
00.00.0000 00:00 Add new
1.
2.
3. Press OK and set the start date for the program. Press OK
4. Press OK and set the start time for the program. Press OK
5. Press OK and set the mode for the program. Press OK. You
can select from the following:
Select the switch moment to be deleted at mode
Select the switch moment to be deleted at mode
NOTE! Be sure to set the end time to
the control according to the excep-
tion schedule! Set the date and time at
which the control goes to
In this case, the control returns
back to the weekly schedule.
Do same kind of selection to ”Repeat”
eld as you did at the start time (for ex-
ample, if you chose the start time peri-
od that repeats monthly, also select the
end time repeats monthly).
1.
2. Select an unused special day and press OK.
3.
the program (hours and minutes are set separately). Select the
the program by pressing OK when the cursor is on OK.
4.
will change from selected mode back to normal mode. Accept
-
trol periods for the same special day.
• one day schedule from the weekly schedule (Monday -
Sunday)
•
•
day program is used during the set time period. You can
also make special day programs (SD) in Ounet and take
6.
year same time.
Settings
Supply water min limit 12.0 °C >
Min lmt increase outd. temp. -20 3.0 °C >
Supply water max limit 42.0 °C >
I-control ’s max effect on supp. wtr 2.0 °C >
Asetusarvot
Huonelämpötila 21.0 °C >
Lämmönpudotus ( huonelämpö ) 1.5 °C >
Suuri lämmönpudotus ( huonelämpö ) 5.0 °C >
Menoveden minimiraja 12.0 °C >
Settings
Room temperature 21.0 °C >
Temperature drop (room temperature ) 1.5 °C >
Big temperature drop (room temperature )5.0 °C >
Supply water min limit 12.0 °C >
•
•
-
•
There is a
-
Huonelämpötila
21.0°C
min: 0.0 max: 95.0
Room temperature
21.0°C
min: 0.0 max: 95.0
-
H1 SETTINGS
H2 SETTINGS
H1 Settings:
Room temperature = 21.5°C/
Temp.drop = 3.0°C/
18
-
-
pending on what you actually control with the relay in question.
Room selection
Name of room 1 Room 1 >
Name of room 2 Room 2 >
Huone 1 nimi
Hyväksy: paina pitkään OK:ta
Peruuta: Paina pitkään ESC:iä
Hu o n e 1
Huone 1 nimi
Hyväksy: paina pitkään OK:ta
Peruuta: Paina pitkään ESC:iä
A s u n t o 1 A
Name of room 1
Approve: Press OK for a number of seconds
Cancel: Press ESC for a number of seconds
Room1
Approve: Press OK for a number of seconds
Cancel: Press ESC for a number of seconds
Apa r t m e n t 1 A
Name of room 1
OK
Key words:
Active alarms
Alarm history
KEY WORDS
ACTIVE ALARMS
ALARM HISTORY
-
has switched to the desired control mode.
20
-
-
lation to most common cabinets. Detachable strip connectors make installation easier.
Info button
Detachable connector shield
Detachable strip connector shield
Acknowledge alarm button
Alarm led
Display connector
RJ-45 connector, cable
length max 25 m
USB host connector
Dimensions:
I/O extension connector
Here are two screw ternimals Modbus RTU lines
50
45
Ethernet connector
OK
Control knob and OK button
US-device-connetor(not in use)
Other manuals for Ouflex A
1
This manual suits for next models
1
Table of contents
Other OUMAN Microphone System manuals
