Outdoor Gourmet FSOGBG3005 Installation instructions

Triton Classic Gas & Charcoal Grill
Model #: FSOGBG3005
Customer Service: [phone], 7:00 am to 12:00 am daily CST
Live Chat on Academy Website (www.academy.com) 24/7 or email
[e-mail]
(Made in China)
Please keep this instruction manual for future reference
Assembly Instructions
& User’s Manual

Warnings…………………………………………………………………..3-7
Tools and Parts…………………………………………………...………8-9
Exploded View………………………………………………………….....10
Hardware…………………………………………………………………...11
Assembly Instructions………………………………………….……..12-23
Operating Instructions……………………………………………......24-27
Trouble Shooting……………………………………………………..…...27
Care and Maintenance…………………………………………..…...28-29
Frequently asked questions……………………………………...…..….30
Warranty Information………………………………………....................31
Table of Contents
Page 2 of 31

Page 3 of 31

Page 4 of 25
Warnings

Warnings
Page 5 of 31

Page 6 of 31
Warnings

Warnings
Page 7 of 31

1 Adjustable wrench
（not included）
2 Screwdriver
（not included）
Tools Required
Page 8 of 31

Parts List
Page 9 of 31

Exploded View
Page 10 of 31

Hardware
Page 11 of 31

Assembly Instructions
Step 1:
Assemble the bottom shelf (1)
to the left leg (2) and right leg
(3) using BOLT M6X50 (DD)-
4PCS
Step 2:
Assemble the long fence rails
(4) to both legs using BOLT
M6X12 (AA)- 8PCS.
Page 12 of 31

Assembly Instructions
Step 3:
Assemble the threaded casters
(5)-4PCS to legs by twisting
clockwise until tight.
Turn over the bottom assembly
when completed and lock all
casters to prevent from moving.
Step 4:
Align and place body (6) on
top of the legs.Using BOLT
M6X12 (AA)- 10 PCS,attach
triangular bracket left (8) and
right (7) to back of body and
legs.
Secure front of body to legs
using BOLT M6X12 (AA)-2
PCS
Page 13 of 31

Assembly Instructions
Step 5:
Screw in BOLT M6X12 (AA)- 2
PCS halfway on the upper
corner of side burner body (9)
as shown IMAGE 1..Slide the
two screws into the opening as
shown IMAGE 2 to hold the
side burner body in position.
Using BOLT M6X12 (AA)-
4PCS,fasten the side burner
body in place and tighten all
screws.
Install the battery (JJ) into the
ignitor with positive facing up.
Step 6:
Mount knob base (10) to front
of side burner body using
BOLT M4X8 (FF)-2PCS.Push
the knob (11)into side burner
controller.Refer tp IMAGE 3.
Page 14 of 31

Assembly Instructions
Step 7:
Assemble the side burner (12)
by sliding it into the top of the
side burner body.
Secure burner to body using
BOLT M4X8 (FF)-2PCS.
Affix the terminal to gas
controller .Refer to IMAGE 4.
Step 8:
Place Side burner grate (13) into
side burner.
Page 15 of 31

Assembly Instructions
Step 9:
Assemble the firebox handle (15)
to firebox lid (14) using
BOLTM6X15 (BB)-2PCS.
Step 10:
Screw in BOLT M6X12 (AA)-
2PCS halfway on the firebox (14)
as shown IMAGE 5..Slide in the
two screw in opening as shown
IMAGE 6 to hold the firebox in
position.Using BOLT M6X12
(AA)-9PCS, fasten the firbox in
place and tighten all screws.
Page 16 of 31

Assembly Instructions
Step 11:
Place cooking grate (17)- 1PC
and charcoal pan (16)-1PC into
firebox.
Step 12:
Slide drip tray (18) underneath
right side of the body.Slide drip
pan (37) underneath drip tray
(36) as shown IMAGE 7,and
slide drip tray (36) underneath
left side of the body.
Page 17 of 31

Assembly Instructions
Step 13:
Assemble Charcoal pan (19) to
body (charcoal side) using BOLT
M6X12 (AA)-4PCS.
Step 14:
Assemble Charcoal pan lift rod
(20) to long “U”plate on
charcoal pan and short “U”plate
on body using PIN ROLL (HH)-
2PCS and COTTER PIN (II)-
2PCS. Refer to IMAGE 8.
Page 18 of 31

Assembly Instructions
Step 15:
Assemble lift knob (21) and air
vent handle (22) on body.
Step 16:
Assemble back panel (23) to
back side of gas side using
BOLT M6X12 (AA)-3PCS.
Page 19 of 31

Assembly Instructions
Step 17:
Step 18:
Page 20 of 31
Remove the screws pre-
assembled on the thermometers
(38). Assemble them to the
charcoal lid (24) and gas lid (25)，
and secure with the screws as
shown IMAGE 9.
Assemble lid Hinges (27)-4PCS
on gas lid (24) and charcoal lid
(25) using BOLT M6X40 (CC)-
8PCS and NUT M6 FLANGE
LOCK (EE)-8PCS.
Assemble bottom Hinges (26)-
4PCS on body (gas and
charcoal side) using BOLT
M6X40 (CC)-8PCS .
Align and place gas lid on top of
the body (left side). Place PIN
ROLL(GG)-2PCS through the
hinges as shown IMAGE 10 and
secure with COTTER PIN (II)-
2PCS as shown IMAGE 11.
Repeat the steps above with the
Charcoal lid on the right side of
the body.