Outdoor Gourmet FSODBG1204 User manual

TRITON GAS
Model #: FSODBG1204
Customer Service: [phone], 8:00am to 10:00pm,Monday thru Saturday
9:00am to 8:00pm Sunday
Central Standard Time
(Made in China)
Please keep this instruction manual for future reference
User Manual

Table of Contents
•Warnings 3-4
•Tools and Parts 5-6
•Hardware 7
•Assembly Instructions 8-19
•Care and Maintenance 20-29
•Warranty Information 30
Page 2 of 30

Warnings Warnings Warnings Warnings
FOR YOUR SAFETY: FOR YOUR SAFETY: FOR YOUR SAFETY: FOR YOUR SAFETY:
1.Read this User Manual before attempting to assemble or
operate your grill.
2.Follow all safety instructions.
3.Check for leaks according to directions in this Grill Guide
before operating your grill, even if you purchased this grill
assembled.
4.Keep this Grill Guide for future reference.
5.Contact 1-888-922-2336 1-888-922-2336 1-888-922-2336 1-888-922-2336 should you need assembly
assistance or have any questions.
THIS GRILL IS FOR OUTDOOR USE ONLY. THIS GRILL IS FOR OUTDOOR USE ONLY. THIS GRILL IS FOR OUTDOOR USE ONLY. THIS GRILL IS FOR OUTDOOR USE ONLY.
If stored indoors, then detach and leave propane cylinder
outside.
TO THE INSTALLER OR PERSON ASSEMBLING THIS GRILL: TO THE INSTALLER OR PERSON ASSEMBLING THIS GRILL: TO THE INSTALLER OR PERSON ASSEMBLING THIS GRILL: TO THE INSTALLER OR PERSON ASSEMBLING THIS GRILL:
Leave this User Manual with the consumer.
TO THE CONSUMER: TO THE CONSUMER: TO THE CONSUMER: TO THE CONSUMER:
Retain this User Manual for future reference.
Page 3 of 30

Warnings Warnings Warnings Warnings
Safety Precautions
Always read and follow all DANGER, WARNING, AND FOR YOUR SAFETY notices in this User
Manual. Failure to follow these notices may result in property damage, bodily injury, or death.
1. Grill installation must conform with local codes, or in their absence, with either the National Fuel
Gas Code, ANSI Z223.1/NFPA 54, Natural Gas and Propane Installation Code, CSA B149.1, or
Propane Storage and Handling Code, B149.2.
2. This gas grill, when installed, must be electrically grounded in accordance with local codes, or, in
the absence of local codes, with the National Electrical Code, ANSI Z21.58-2007, or the Canadian
Electrical Code, CSA 1.6-2007.
3. This gas grill is intended for outdoor use only, and should not be used in a building, garage, or any
other enclosed area.
4. This gas grill is not intended to be installed in or on recreational vehicles and/or boats.
5. Never use any other type of fuel for this grill other than LP gas (propane).
6. Only use the pressure regulator with a type 1 connector that is supplied with this gas grill
7. Before each use, check the gas hose for excessive abrasion, cracking, fraying, wear, or cuts.
Replace a hose assembly showing those signs with the hose assembly specified in the parts list
before using the grill.
8. Always perform a Leak Test before operating your grill.
!
WARNING
1. Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or
any other appliance.
2. An LP cylinder not connected for use should not be stored in the vicinity of this or any other
appliance.
!
DANGER
If you smell gas:
1. Shut off gas to the appliance.
2. Extinguish any open flame.
3. Open lid.
4. If odor continues, keep away from appliance and call your local fire department.
Page 4 of 30

Tools Required
1 Adjustable wrench
(not included)
2 Screwdriver
(not included)
Page 5 of 30

Parts List
Page 6 of 30
s

Hardware
Page 7 of 30

Assembly Instructions
Step 1:
Assemble the
bottom shelf (23)
to the legs(21) using
BOLT M6*50 (AA)-
4PCS and NUT
M6 FLANGE
LOCK (DD)-4PCS.
Step2:
Assemble both of
the long fence rails
(22) to both legs
using BOLT M6*12
(CC)-8PCS.
Page 8 of 30

Assembly Instructions
Step 3:
Assemble the
threaded caster (24)-
4PCS to legs by
twisting clockwise
until tight. Turn over
the bottom assembly
when completed and
lock all casters to
prevent from moving.
Step 4:
Assemble the
bottom hinges (7)-
2PCS to the back
left side of body (9)
using BOLT
M6*40 (EE)-4PCS
Page 9 of 30

Assembly Instructions
Step 5:
Align and place body
on top of the legs.
Using BOLT M6*12
(CC)-10PCS, attach
the triangular bracket
left (20) and right (19)
to backside of body
and legs as shown in
the Fig.1. Secure front
of body to legs using
M6*12 (CC)-2PCS
with M6 SPACER (II)-
2PCS.
Step 6:
Assemble gas tank
holder (25) and gas
tank hook (26) on the
left leg using BOLT
M6*12 (CC)-4PCS.
FIG.1
Page 10 of 30

Assembly Instructions
Step 7:
Screw in BOLT M6*12
(CC)-2PCS halfway on
the upper corners of the
side burner body (13) as
shown in Fig. 2a.
Slide in the two screws
in opening (Fig. 2b) to
hold the side burner
body in position. Using
M6*12 (CC)-4PCS,
fasten the side burner
body in place and tighten
all screws.
Step 8:
Mount knob base (11) to
front of side burner body
using BOLT M4*12 (HH)-
2PCS. Push knob (12)
into side burner controller.
FIG.2a
FIG.2b
Slide drip pan (8) into
the griddle body (9).
Page 11 of 30

Assembly Instructions
Step 9:
Assemble the side
burner (14) by sliding it
on the top center of
the side burner body.
Secure burner to body
using BOLT M4*8
(HH)-2PCS.
Affix the terminal to
gas controller as
shown in Fig. 3.
Fig. 3
Step 10:
Assemble back
panel(1) to back
side of gas side
using BOLT
M6*12(CC)-3PCS.
Page 12 of 30

Assembly Instructions
Step 12:
Align and place gas
lid on top of the body.
Place PIN ROLL
(BB)-2PCS through
the hinges and secure
with COTTER PIN
(FF)-2PCS.
Step 11:
Assemble lid Hinges
(2)-2PCS on gas lid
(3) using M6*40
(EE)-4PCS and NUT
M6 (DD)-4PCS.

Assembly Instructions
Step 14:
Assemble the
warming rack(4) by
inserting the top two
ends to gas lid and
bottom side to body.
Secure the top part of
warming rack with
COTTER PIN (FF)-
2PCS.
Step 13:
Place flame tamers
(6)-3pcs into gas
side of body. Refer
on Fig. 4.
FIG.4
Page 14 of 30

Assembly Instructions
Step 16:
Assemble the
support plates (17)
and extension wire
(27) on front sides
of the body using
BOLT M6*12 (CC)-
6PCS.
Step 15:
Place cooking grates
(5)-2PCS into body.
Page 15 of 30

Assembly Instructions
Step 18:
Install side shelf
support (29)
between the lower
connecting slice
mount using PIN
ROLL (GG)-2PCS
and COTTER PIN
(FF)-2PCS
Step 17:
Mount connecting
slice-A (30)-2PCS
and –B (31)-2PCS
on the right sides of
body using M6*12
(CC)-8PCS. Refer
on Fig.5 for proper
placement.
FIG.5
Page 16 of 30

Assembly Instructions
Step 20:
Place griddle top
(10) onto body.
Step 19:
Assemble the side
shelf (28) between
the upper connecting
slice using PIN ROLL
(GG)-2PCS and
COTTER PIN (FF)-
2PCS.
Page 17 of 30

Assembly Instructions
Step 21:
Assemble the handle
(32)to drip tray (18)
using BOLT M6*12
(CC)-2PCS.
Slide drip tray
underneath the body.
Page 18 of 30

FULLY ASSEMBLY
Page 19 of 30

General Information and Instructions
Your new Outdoor Gourmet™ Grill has been designed and manufactured to high quality standards. It will
provide you with many years of enjoyment with a minimal amount of maintenance. Please keep in mind the
following FOR YOUR SAFETY.
OPERATION
1. Your gas grill requires reasonable care during operation. It will be hot during cooking and cleaning.
You should never leave the grill unattended or move the grill when in use.
2. Children should never use your gas grill. Keep younger children and pets away when in use.
3. Only use your gas grill outside in a well-ventilated area. Never use indoors in any building, garage,
shed, or under any type of flammable canopy or overhang.
4. Ensure your grill is on level ground and the locking casters are locked before use.
5. Turn all gas valves off should the burners go out when cooking. Open the lid and wait 5 minutes before
relighting.
6. Do not lean over the grill or touch the edges of the firebox or lid when in use.
7. Turn the burners off, close the lid, and shut off the LP cylinder should a grease fire occur.
8. Do not obstruct the flow of combustion and ventilation air to this grill.
9. Keep the outdoor cooking gas appliance area clear and free from combustible materials, gasoline, and
other flammable vapors and liquids.
10. Keep the ventilation openings of the cylinder enclosure free and clear from debris.
11. Do not put a barbecue cover or other flammable material in the storage area of this grill.
12. Do not use charcoal briquettes, lava rock, or any type of ceramic product in the gas section of this grill.
13. Do not install or use on or in a recreational vehicle and/or boats.
LP Gas and Cylinder Information
Your new gas grill operates on LP (Liquid Petroleum) Gas. It is odorless, colorless, and non-toxic when
produced. You can smell LP gas as it has been given an odor similar to rotten cabbage for your safety.
Your grill uses the newest and safest LP Gas Cylinder.
1. O.P.D. (Overfill Protection Device) – prevents accidental gas leaks
caused by overfilling of the tank. Each tank contains a float that
closes the input valve when the tank is 80% full. This allows room
for the LP gas to expand in hot temperatures. A triangular hand wheel
distinguishes this type of tank.
2. Q.C.C.1 Type 1 Quick Connect Valve – provides fast tank hook-ups and requires only to be tightened by
hand.
In addition, the LP tank you use with your grill must meet the following requirements
1. Required Measurements: 12-1/2” (317mm) in diameter and 18-1/2” (472mm) in height.
2. 20-pound (9.1kg) propane cylinder.
3. Constructed and marked with U.S. Department of Transportation (D.O.T.) for the US or CAN/CSA-
B339, Cylinders, Spheres and Tubes for Transportation of Dangerous Goods; and Commission, for
Canada.
4. A safety release valve.
5. A means for vapor withdrawal.
Triangular Hand Wheel
GAS GRILL
Care and Maintenance
Page 20 of 30