Outdoor Gourmet FSOGBG1203 User manual

Triton CG
Model #: FSOGBG1203
Customer Service: [phone], 8:00am to 10:00pm,Monday thru Saturday
9:00am to 8:00pm Sunday
Central Standard Time
(Made in China)
Please keep this instruction manual for future reference
User Manual
Page 1 of 26

Table of Contents
• Warnings 3-4
• Tools and Parts 5-6
•
Hardware 7
• Assembly Instructions 8-15
•
Care and Maintenance 19
-
28
• Care and Maintenance 16-25
• Warranty Information 26
Page 2 of 26

Warnings Warnings Warnings Warnings
FOR YOUR SAFETY: FOR YOUR SAFETY: FOR YOUR SAFETY: FOR YOUR SAFETY:
1.Read this Grill Guide before attempting to assemble or
operate your grill.
2.Follow all safety instructions.
3.Check for leaks according to directions in this Grill Guide
before operating your grill, even if you purchased this grill
assembled.
4.Keep this Grill Guide for future reference.
5.Contact 1-888-922-2336 1-888-922-2336 1-888-922-2336 1-888-922-2336 should you need assembly
assistance or have any questions.
THIS GRILL IS FOR OUTDOOR USE ONLY. THIS GRILL IS FOR OUTDOOR USE ONLY. THIS GRILL IS FOR OUTDOOR USE ONLY. THIS GRILL IS FOR OUTDOOR USE ONLY.
If stored indoors, then detach and leave propane cylinder
outside.
TO THE INSTALLER OR PERSON ASSEMBLING THIS GRILL: TO THE INSTALLER OR PERSON ASSEMBLING THIS GRILL: TO THE INSTALLER OR PERSON ASSEMBLING THIS GRILL: TO THE INSTALLER OR PERSON ASSEMBLING THIS GRILL:
Leave this Grill Guide with the consumer.
TO THE CONSUMER: TO THE CONSUMER: TO THE CONSUMER: TO THE CONSUMER:
Retain this Grill Guide for future reference.
Page 3 of 26

Warnings Warnings Warnings Warnings
Safety Precautions
Always read and follow all DANGER, WARNING, AND FOR YOUR SAFETY notices in this Grill
Guide. Failure to follow these notices may result in property damage, bodily or physical injury, or death.
1. Grill installation must conform with local codes, or in their absence, with either the National Fuel
Gas Code, ANSI Z223.1/NFPA 54, Natural Gas and Propane Installation Code, CSA B149.1, or
Propane Storage and Handling Code, B149.2.
2. This gas grill, when installed, must be electrically grounded in accordance with local codes, or, in
the absence of local codes, with the National Electrical Code, ANSI Z21.58-2007, or the Canadian
Electrical Code, CSA 1.6-2007.
3. This gas grill is intended for outdoor use only, and should not be used in a building, garage, or any
other enclosed area.
4. This gas grill is not intended to be installed in or on recreational vehicles and/or boats.
5. Never use any other type of fuel for this grill other than LP gas (propane).
6. Only use the pressure regulator with a type 1 connector that is supplied with this gas grill
7. Before each use, check the gas hose for excessive abrasion, cracking, fraying, wear, or cuts.
Replace a hose assembly showing those signs with the hose assembly specified in the parts list
before using the grill.
8. Always perform a Leak Test before operating your grill.
!
WARNING
1. Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or
any other appliance.
2. An LP cylinder not connected for use should not be stored in the vicinity of this or any other
appliance.
!
DANGER
If you smell gas:
1. Shut off gas to the appliance.
2. Extinguish any open flame.
3. Open lid.
4. If odor continues, keep away from appliance and call your local fire department.
Page 4 of 26

1 Adjustable wrench
(not included)
2 Screwdriver
(not included)
Tools Required
Page 5 of 26

Parts List
sBack Panel
Side Shelf(Left)
Page 6 of 26

Hardware
Page 7 of 26

Assembly Instructions
Step 1:
Assemble the
fence rail(21) to
the left and right
M6*50(AA)-4PCS
and NUT M6
FLANGE LOCK (DD)-
4PCS.
Step 2:
Assemble fence
rail(21) between
legs using BOLT
M6X12(BB)-4PCS.
legs(20) using BOLT
Page 8 of 26

Assembly Instructions
Step 4:
Align and place
body(12) on top of
the legs. Using BOLT
M6*12 (BB)-20PCS,
attach the triangular
bracket left (15)-
2PCS and right (14)-
2PCS to body and
legs .
Step 3:
Assemble the
threaded casters (22)
to legs by twisting
clockwise until tight.
Turn over the bottom
assembly when
completed and lock
all casters to prevent
from moving.
Page 9 of 26

Assembly Instructions
Step 5:
Assemble gas tank
holder(24) and gas
tank hook(23) on the
left leg using BOLT
M6X12(BB)-4PCS.
Assemble the bottom
hinges (13)-4PCS to
the back of body
using BOLT M6*40
(CC)-8PCS.
Step 6:
Screw in BOLT M6*12
(BB)-2PCS halfway on
the upper corners of
the side shelf-L(25) as
shown.
Using M6*12 (BB)-
4PCS, fasten the left
side shelf in place and
tighten all screws.
The same as right side
shelf(26).
Page 10 of 26

Assembly Instructions
Step 7:
Assemble back
panel(8) to back
side of gas body
using BOLT
M6X12(BB)-
3PCS .
Step 8:
Assemble lid Hinges
(4)-2PCS on gas lid
(1) using M6*40 (CC)-
4PCS and NUT M6
FLANGE LOCK (DD)-
4PCS.
Page 11 of 26

Assembly Instructions
Step 9:
Assemble lid Hinges (4) -
2PCS on charcoal lid (2)
using M6*40 (CC) -4PCS and
NUT M6 FLANGE LOCK
(DD)-4PCS. Attach the
charcoal stack (3) on
charcoal lid using BOLT
M6*12 (BB) -2PCS and NUT
M6 FLANGE LOCK (DD )-
2PCS. Assemble the lid
handle (6) and lid handle base
(5) to charcoal lid using
Step 10:
Align and place gas lid
on top of the body (left
side). Place PIN ROLL
(EE)-2PCS through the
hinges and secure with
COTTER PIN (FF)-
2PCS.Align and place
charcoal lid on top of the
body (right side). Place
PIN ROLL (EE)-2PCS
through the hinges and
secure with COTTER
PIN (FF)-2PCS.
Page 12 of 26
M6*40(CC)-2PCS.

Assembly Instructions
Step 12:
Assemble lifting
handle(16)-2PCS to
charcoal pan(17).
Lower lifting system to
body(charcoal side) .
Put flame tamers(11)-
3PCS to gas side of body.
Step 11:
Assemble the warming
racks(9) -2PCS by inserting
the top two ends to lids
and bottom side to body.
Secure the top part of
warming rack with
COTTER PIN (FF)-4PCS.
Assemble the
hooks(7) to front of right
side shelf by twisting
Page 13 of 26
counterclockwise until tight.
Assemble the knob(18) to
the body by twisting half
way. Do not tighten all the
way or the vent will not
open and close.

Assembly Instructions
Step 14:
Step 13:
Slide drip trays (19)-
2pcs underneath
each side of the
body.
Install battery to
ignition button by
gently removing the
cap, placing battery
(GG) and putting
back the cap.
Place cooking grates
(10)-4PCS into body.
Page 14 of 26

FULLY ASSEMBLY
Page 15 of 26

General Information and Instructions
Your new Outdoor Gourmet™ Grill has been designed and manufactured to high quality standards. It will
provide you with many years of enjoyment with a minimal amount of maintenance. Please keep in mind the
following FOR YOUR SAFETY.
OPERATION
1.
Your gas grill requires reasonable care during operation. It will be hot during cooking and cleaning.
You should never leave the grill unattended or move the grill when in use.
2.
Children should never use your gas grill. Keep younger children and pets away when in use.
3.
Only use your gas grill outside in a well-ventilated area. Never use indoors in any building, garage,
shed, or under any type of flammable canopy or overhang.
4.
Ensure your grill is on level ground and the locking casters are locked before use.
5.
Turn all gas valves off should the burners go out when cooking. Open the lid and wait 5 minutes before
relighting.
6.
Do not lean over the grill or touch the edges of the firebox or lid when in use.
7.
Turn the burners off, close the lid, and shut off the LP cylinder should a grease fire occur.
8.
Do not obstruct the flow of combustion and ventilation air to this grill.
9.
Keep the outdoor cooking gas appliance area clear and free from combustible materials, gasoline, and
other flammable vapors and liquids.
10.
Keep the ventilation openings of the cylinder enclosure free and clear from debris.
11.
Do not put a barbecue cover or other flammable material in the storage area of this grill.
12. Do not use charcoal briquettes, lava rock, or any type of ceramic product in the gas section of this grill.
13.
Do not install or use on or in a recreational vehicle and/or boats.
LP Gas and Cylinder Information
Your new gas grill operates on LP (Liquid Petroleum) Gas. It is odorless, colorless, and non-toxic when
produced. You can smell LP gas as it has been given an odor similar to rotten cabbage for your safety.
Your grill uses the newest and safest LP Gas Cylinder.
1. O.P.D. (Overfill Protection Device) – prevents accidental gas leaks
caused by overfilling of the tank. Each tank contains a float that
closes the input valve when the tank is 80% full. This allows room
for the LP gas to expand in hot temperatures. A triangular hand wheel
distinguishes this type of tank.
2. Q.C.C.1 Type 1 Quick Connect Valve – provides fast tank hook-ups and requires only to be tightened by
hand.
In addition, the LP tank you use with your grill must meet the following requirements
1. Required Measurements: 12-1/2” (317mm) in diameter and 18-1/2” (472mm) in height.
2. 20-pound (9.1kg) propane cylinder.
3. Constructed and marked with U.S. Department of Transportation (D.O.T.) for the US or CAN/CSA-
B339, Cylinders, Spheres and Tubes for Transportation of Dangerous Goods; and Commission, for
Canada.
4. A safety release valve.
5. A means for vapor withdrawal.
Triangular Hand Wheel
GAS GRILL
Care and Maintenance
Page 16 of 26
14.

!
WARNING
A frosty cylinder valve indicates possible gas overfill. Close the LP valve and call your dealer
immediatel
y
.
!
WARNING
1. Never store any extra cylinders near your grill.
2. Keep cylinders out of direct sunlight and high heat.
3. Never fill your cylinder over 80% full by volume. This may cause release of gas from the safety
release valve.
4. Immediately call your LP dealer or fire department should you hear, smell, or see escaping gas
from the cylinder.
5. Do not insert any type of foreign objects into the valve outlet.
!
WARNING
1. The gas supply must be turned off at the LP-gas supply cylinder when this outdoor cooking gas
appliance is not in use.
2. Storage of this gas grill indoors is permissible only if the cylinder is disconnected and removed from
the gas grill.
3. Cylinders must be stored outdoors out of reach of children and must not be stored in a building,
garage, or any other enclosed area.
TRANSPORTATION AND STORAGE
1. Always use the Safety Cap when transporting or storing your cylinder.
2. Do not store in a building, garage, or other enclosed area.
3. Always store your cylinder outside.
4. Store out of reach of children.
5. Always transport in an upright position.
6. Do not smoke when transporting your cylinder.
Dust Cap
!
WARNING
1. Do not attempt to use a cylinder with any other type of connection device.
2. Do not attempt to use a cylinder with a larger capacity
Page 17 of 26

Regulator and LP Cylinder Connections
Your regulator is equipped with a Q.C.C. Type 1 quick connect system. It will not allow gas to flow until a
positive seal has been made. It has a thermal element that will shut off the gas flow if the temperature reaches
240 degrees F (115 degrees C). It also has a flow-limiting device that will restrict the flow of gas to 10 cubic
feet per hour (0.28 cubic meters per hour).
Before each use, check the gas hose for excessive abrasion or wear, or cuts. Replace a hose assembly showing
those signs with the hose assembly specified in the parts list before using the grill.
TO CONNECT THE CYLINDER TO THE REGULATOR AND HOSE
1. Be sure the LP cylinder is “OFF” by turning the hand wheel clockwise
until it stops.
2. Place the cylinder on the hook beside of body
with the valve
facing outward. See Assembly Instructions to secure.
3. Be sure all burner controls are turned to the “Off” position.
4. Remove the safety cap from the from the cylinder valve.
5. Center the nipple of the regulator into the cylinder valve
6. Turn the black nut clockwise until it stops. Hand Tighten Only.
Do Not Use A Wrench.
!
CAUTION
The gas pressure regulator provided with this outdoor cooking appliance must be used. This regulator is set
for an outlet pressure of 11 inches water column.
Center this nipple of the
regulator into the cylinder
valve.
The regulator must enter the
cylinder valve in a straight
line.
Q.C.C.1 Type 1 Connector
!
WARNING
Always keep the gas cylinder in
!
WARNING
1. Do not connect this grill to any unregulated sources of propane.
2. Before each use, check the gas hose for excessive abrasion or wear, or cuts. Replace a hose
assembly showing those signs with the hose assembly specified in the parts list before using the
grill. Inspect the hose assembly underneath the left side shelf and following the regulator hose up
to its connection to the gas manifold assembly.
3. Always perform the Leak Test listed below before using your grill for the first time, if the cylinder
has been changed, any gas components have been changed, the regulator flow-limiting device has
been activated, or after a long period of non-use.
4. Do not attempt to connect this grill to the LP system of a motor home or trailer.
the upright position at all times.
Page 18 of 26

LEAK TESTING THE REGULATOR, VALVES, HOSES, AND CONNECTIONS
1. Ensure the LP cylinder valve and all burners are “Off”.
2. Ensure the LP cylinder is connected to the regulator.
3. If the information in the above steps is not followed exactly, a fire causing death or
4. Mix up a solution of 50% water and 50% liquid dish soap. Do not use any household cleaner
solution.
5. Open the LP tank valve by turning the hand wheel counterclockwise one turn. If you hear a rushing
sound, turn the gas off immediately. In that case, there could be a leak at the connection. Reconnect
the cylinder to the regulator.
6. Spray or brush on the solution covering the following areas: cylinder welds, regulator and cylinder
connection, gas hose connections to the regulator, all gas hoses, all gas hose connections to the
burners including the main and side burners.
7. Growing bubbles on any of the parts and connections listed above indicate a gas leak. Immediately
shut off the LP tank valve by turning the valve clockwise. Retighten the connections or order
replacement parts as needed. Continue to test as necessary until no leaks are detected.
8. Close the LP tank valve by turning the hand wheel clockwise.
Grill Placement
!
WARNING
1. DO NOT USE THE GRILL if you cannot stop the leaks. Be sure the LP cylinder valve is closed.
If the LP cylinder is still leaking, contact your LP dealer or local fire department.
2. Do not use any match or open flame, or smoke, during leak testing.
3. Do not light a burner during leak testing.
4. The replacement hose assembly must be the one identified.
!
FOR YOUR SAFETY
1. Minimum clearance from sides and back of unit to adjacent combustible construction below top
of unit, 36 inches (91 cm) from sides and 36 inches (91 cm) from back.
2. Do not locate this outdoor cooking gas appliance under overhead-unprotected combustible
surfaces.
APARTMENT RESIDENTS
Check with your apartment manager regarding
your regulations for barbecues.
!
WARNING
1. Do not use this grill in any enclosed
area, garage, shed, or under any type of
overhead structure or canopy.
2. Operate this grill only in a well-
ventilated area.
Do not face the grill directly into the wind. Keep any electrical supply cord and the fuel
supply hose away from any heated surfaces and
water.
WARNING
WARNING
!
!
!
Page 19 of 26
If the information above is not followed exactly, a fire causing death or serious injury may occur.
36
36"

LIGHTING
Always visually inspect your grill before lighting. Replace any hoses that are frayed or cracked before lighting
your grill. Look for anything that may be blocking spaces for ventilation and remove. After lighting, always
check the flame to ensure you have a good flame all along each burner. If not able to light, or the flame is not
even along the entire burner(s), then see the Trouble Shooting section
!
WARNING
1. Read instructions before lighting.
2. Open lid during lighting.
3. If ignition does not occur in 5 seconds, turn the burner control(s) off, wait 5 minutes and repeat the
lighting procedure as below:
LIGHTING THE MAIN BURNERS USING ELECTRONIC IGNITION
1. Open the lid.
2. Ensure all burner control knobs are in the “Off” position.
3. Turn on the LP gas by turning the hand wheel on the cylinder valve.
4. Turn one burner control knob marked with an igniter flame “ ” to “High”.
5. Depress the electronic ignition button and hold down. You should hear a
clicking sound, which shows the electronic ignition is working.
6. If the burner does not light within 5 seconds, turn the burner control knob to “Off”. Wait 5 minutes for the
gas to clear, and repeat the above procedure. Use the Manual directions if it still will not light.
7. When lit, turn the control knob to the desired setting.
8. Your grill is equipped with continuous ignition. Simply turn the control knob of the burner next to the lit
burner to HI. It will light automatically. Do not press the electronic ignition button again. Then adjust
control knob(s) to desired settings.
MANUALLY LIGHTING THE MAIN BURNERS WITH THE MATCH LIGHTING STICK
1. Open the lid.
2. Ensure all burners are in the “Off” position.
3. Slowly turn on the gas at the LP tank valve if it is not already on.
4. Place a match in the Match Holder. This is located in the top center
drawer of the grill cabinet underneath the right main burner.
5. Use the holder to slide the lit match though the cooking grates and the
front of the heat tent to the left of the burner you wish to light.
6. Press and turn the burner control knob to “HI/LIGHT”. Continue to push
in and hold up to 5 seconds or until the burner lights.
7. If the burner does not light within 5 seconds, turn the burner control
knob to “Off”. Wait 5 minutes for gas to clear, and try again.
8. When lit, turn the control knob to the desired heat setting.
LIGHTING THE SIDE BURNER WITH ELECTRONIC IGNITION
1. Open the side burner cover
2. Ensure the side burner control knob is in the “Off” position, as well as any main burners not in use.
3. Turn on the LP gas if it is not already on.
4. Turn the side burner control knob to “High”.
5. Depress the electronic ignition button and hold. You should hear a clicking sound, which shows the
electronic ignition is working.
6. If the burner does not light within 5 seconds, turn the burner control knob to “Off”. Wait 5 minutes for the
gas to clear, and repeat the above procedure. Use the Manual directions if it still will not light.
7. When lit, turn the side burner control knob to its desired setting.
Grill Operations
Page 20 of 26