Outdoor GreatRoom Company VNG-2424BRN User manual

1
The Vintage Fire Pit Table
Installation Instructions for Vintage Fire Pit Table
VNG-2424BRN
fire-parts.com

2
fire-parts.com

3
Contents
Required Tools…………………………….…..2
Placing and assembling the Table.………3
Gas Connection………………………….…….4
Igniter Installation…………….……………...6
Locating Propane tank………………………7
Finishing Touches……………………………7
Required Tools
Utility Knife
To cut and remove packaging
2 Open Ended Wrenches
To secure gas connections
Leather Gloves
To protect hands from rough edges
found on coffee table during
installation.
One AAA battery (not Included)
Required for electric spark igniter
installation
Two people are required for this
installatio
90250 Rev A 4.2.15
IMPORTANT
Please consult your Crystal Fire instruction manual for detailed
instructions and important information related to burner installation,
including safety information, proper tightening of connections with
two wrenches, and full burner setup and lighting instructions.
DO NOT ATTEMPT TO INSTALL CF-2424 BURNER WITHOUT FIRST
CONSULTING THE CRYSTAL FIRE OWNER’S MANUAL.
Contents
Required Tools……………………………………………….3
Included with your Fire Pit…………………………..…4
Assembly Instructions…………………………………….5
Gas Connections………………………………….………...6
Igniter Installation………………………………………….8
Glass Installation……………………………………..……10
Required Tools
Two people are required for this installation
2 Open Ended Wrenches
To secure gas connections
Leather Gloves
To protect hands from rough edges found on fire pit during
installation
One AAA Battery (not included)
Required for electric spark igniter installation
Utility Knife
To cut and remove packaging
42452 REV D 08-20-18
fire-parts.com

4
Included with your Fire Pit
Base
Top
CF-2424 Square Burner
fire-parts.com

5
Assembly Instructions
1. Open packaging and remove the access door before
removing the fire pit base from the box.
2. Set the base in the desired location and set top onto
base. Ensure top is aligned with the wood dowels,
found in each corner. Replace access door.
Wood Dowel
(Shown in red)
fire-parts.com

6
Gas Connections
1. Reach inside the burner cut-out and attach natural gas supply
line using a 3/8” flare fitting, or attach the included black
rubber propane hose and regulator to the bottom fitting of the
control valve.
TIGHTEN SECURELY WITH A WRENCH
2. Lay the burner upside down on a flat, soft surface to avoid
scratching the polished metal. Ensure the correct orifice is
installed for the fuel type you are using (see Crystal Fire user
manual included with burner for orifice sizing information)
Attach the included metal flex hose to the burner.
TIGHTEN SECURELY WITH TWO WRENCHES
Read and understand your Crystal Fire owner’s manual before
beginning burner hookups or using the device.
Do not use Teflon tape or pipe dope on flare fittings.
Propane input
Natural gas input
or
Natural gas supply line
as specified by local
building codes
Gas Connections
fire-parts.com

7
3. Set the burner into the fire pit table exactly as
shown and make final gas connection to the
control panel.
Igniter
Igniter
Metal flex line to
burner
ONLY
TIGHTEN CONNECTION
SECURELY WITH WRENCH
Sparker
Access Door
fire-parts.com

8
Igniter Installation
1. Make sure the valve is in the OFF
position before beginning.
2. Install sparker as shown, using an
AAA battery (not included).
3.
Sparker will not operate correctly without an ignition and ground
wire attached.
Plug both BLACK wires hanging from the burner into
the back of the sparker box. If an orange wire is
present, do not use it. Orange wire is for automatic
ignition system add-on only.
Test system by pushing the button on the igniter.
Consult the troubleshooting section if spark is weak,
intermittent, or not present.
fire-parts.com

9
After installing igniter and making gas connections, verify that
they are tight and that no leaks are present using a solution of
soapy water or a commercially available leak-check solution.
Position Your Tank
(If Applicable)
1. Remove door, connect the propane hose/regulator to the
propane tank and hand-tighten (DO NOT USE A WRENCH) and
slide the propane tank past the solid red line to ensure the door
closes properly.
2. With tank inside base, ensure that no hoses, wires, or anything
else is kinked or touching the burner pan.
fire-parts.com

10
IMPORTANT
Please consult your Crystal Fire instruction manual for detailed
instructions and important information related to burner installation,
including safety information, proper tightening of connections with
two wrenches, and full burner setup and lighting instructions.
DO NOT ATTEMPT TO INSTALL CF-2424 BURNER WITHOUT FIRST
CONSULTING THE CRYSTAL FIRE OWNER’S MANUAL.
WARNING
After consulting the manual and following instructions, remember: before
operating, all gas connections must be fully checked for leaks
Glass Installation
1. Scatter all the included glass beads evenly onto burner
surface.
DO NOT OPERATE CRYSTAL FIRE BURNER WITHOUT
INCLUDED GLASS BEADS
fire-parts.com

11
Warranty: Fire pit tables are covered under a 1-
year manufacturer’s warranty. Please visit
http://www.outdoorrooms.com/warranty-form/
to register your product.
Thank you for purchasing an
Outdoor GreatRoom Company
product! This fire pit was made with
pride in the USA.
14400 Southcross Drive West •Suite 100 •Burnsville, MN 55306
Toll Free: 1-866-303-4028 •[e-mail]
fire-parts.com