overstock 80600 User manual

Email: [email protected]
Within 30 days from delivery date
Made In China
ASSEMBLY INSTRUCTIONS
JASLENE BUFFET/MEDIA CABINET ITEM# 80600
DATE: 21-SEP-2020
ASSEMBLY
REQUIREMENTS
1 Hour
Assembly Time
(Approximate)
2 -Person Assembly
Tools Required (Not Provided):
Phillips Screwdriver
Flat Head Screwdriver
Thank you for purchasing our product!
Please refer and use this assembly instruction to assemble the product.
Contact our customer service department in case there are any missing or damage parts or hardware.
Replacement parts are normally shipped within 2 or 3 days.
We appreciate your business!
ASSEMBLY PREPARATION
1. Remove all packaging materials, staples and packing straps from the carton.
2. Refer to Parts List and Hardware List and ensure they are correct before assembly.
Contact customer service for missing parts.
3. Place all wooden parts on a clean, flat and soft surface (e.g. carpet or rug) to prevent parts from getting scratched.
SAFETY PRECAUTION:
1. KEEP ALL HARDWARE PARTS OUT OF REACH OF CHILDREN.
2. DISPOSE PLASTIC PACKAGING MATERIAL IMMEDIATELY TO AVOID ANY RISK OF SUFFOCATION TO
CHILDREN AND ANIMALS.
TIPS FOR ASSEMBLY:
1. Allow ample room for assembly and in close proximity to where product will be placed.
2. Assemble the product on a surface that does not scratch or damage the exterior gloss and finish of the furniture.
3. Identify all of the parts, hardware and quantities required for each step.
4. During assembly, do not over-tighten any fittings as this may cause damage.
5. DO NOT USE POWER TOOLS TO ASSEMBLE THIS PRODUCT.
6. Always place the product on a flat, level surface.
7. Do not sit or stand on the partially assembled product; only use the product for which it is intended.
CARE AND MAINTENANCE
- Use a slightly damp cloth to clean the product. Do not use bleach or abrasive cleaning material.
- Check all the fittings periodically and re-tighten as necessary. Do not use the product if any of the parts is
damaged or broken.
- Never allow any kind of liquid to remain on your furniture. Absorption can cause wood to warp or delaminate.
- Do not place hot items (e.g. hot drinks) directly onto the wood surface.
- Do not drag and/or pull the furniture.
This product is for indoor and household use only - not for commercial use.
1/12

R2 pcs
Screw 3*12mm
H8 pcs
Bolt
6*30mm
O2 pcs
Magnetic Catch
P2 pcs
Magnetic Bar
Q4 pcs
Screw 3*14mm
2/12
Hardware List
ITEM PART QTY ITEM PART QTY
A
DESCRIPTION DESCRIPTION
B
C
D
Cam-Bolt 6 pcs
20 pcs
Cam-Lock
Wood Dowel
ASSEMBLY INSTRUCTIONS
JASLENE BUFFET/MEDIA CABINET ITEM# 80600
6*35mm
15*10mm
8*30mm
F
E
6 pcs
G
24 pcs
I
J
K
L
M
N
2 pcs
1 pc
2.5*10mm
Knob Bolt 4*18mm
3.5*40mm
Screw 7*40mm
3.5*14mm
Screw
17 pcs
Knob
6 pcs
2 pcs
8 pcs
4 pcs
2 pcs
2 pcs
Shelf Pin
Screw
Hinge
Plastic Anchor
Allen Wrench
Screw

1 pc
1 pc
12
Right Door
Parts List
ITEM PART QTY ITEM PART
1
3/12
DESCRIPTION DESCRIPTION QTY
7
Connect Bar
Top Panel 1 pc 2 pcs
28
Left Door
Bottom Panel 1 pc
3 9
Right Front
and Left
Back Leg
Left Panel 1 pc 2 pcs
410
Left Front
and Right
Back Leg
Center Panel 1 pc 2 pcs
511
Back Panel
Right Panel 1 pc 1 pc
6
Adjustable
Shelf 2 pcs
ASSEMBLY INSTRUCTIONS
JASLENE BUFFET/MEDIA CABINET ITEM# 80600

4/12
1
ASSEMBLY OVERVIEW
2
3
4
5
6
6
7
7
8
12
11
10
9
9
10
ASSEMBLY INSTRUCTIONS
JASLENE BUFFET/MEDIA CABINET ITEM# 80600

Instructions For Fastening
CAM-BOLT AND CAM-LOCK
Align the arrow on the Cam-lock to the Cam-bolt
head and insert the Cam-lock. Ensure Cam-lock
is fully inserted.
PANEL
Place Cam-bolt to the designated pre-drilled holes on the panel. Use a Phillips Screwdriver to
tighten Cam-bolt vertically until shoulder is flushed (on the same level) with panel. Do not
over-tighten or under-tighten.
CORRECT
Use a Flat-head Screwdriver to turn
Cam-lock clockwise so it locks onto
the head of the Cam-bolt. Turn until
it is snug (about 3/4ths of a turn)
-- over-tightening could damage
Cam-lock or/and Cam-bolt.
CAM-BOLT CAM-LOCK
Tools Required
INSERTING AND TIGHTENING CAM-BOLT
SHOULDER
PANEL
Place Cam-bolt on pre-drilled
hole and screw in vertically.
Shoulder is flushed (on the
same level) with the panel.
Shoulder is above the panel.
PANEL
INSERTING CAM-LOCK
Insert Cam-lock
with arrow align
to Cam-bolt head. WRONG
TIGHTENING CAM-LOCK
5/12

STEP 1
6/12
A
STEP 2
a) Lay Top Panel (1) bottom-side on a material that does not scratch or damage the part.
b) Screw in Cam-bolt (A) into the designated holes on (1). Refer to Page 5 for instructions on inserting
and tightening Cam-bolt.
a) Set Bottom Panel (2) vertically as shown. Position Leg (9 & 10) as shown - note the orientation of each leg
with respect to the straight side and slanted side. Important: the vertical straight side of each leg faces
outward.
b) Align the screw hole on each leg to the screw hole on (2) and fasten (9 & 10) to (2) using Bolt (H). Tighten
(H) using Allen Wrench (L).
6 pcs
1
A
H 8 pcs
10
9
10
9
2
H
L
L1 pc
9
2
10
2
10
2
9
2
Straight
Side Straight
Side

4 pcs
2 pcs
3x14 mm
O
Q
OQ
Q
O
STEP 4
7/12
STEP 3
a) Insert Wood Dowel (C) into designated hole on bottom edge of Left Panel (3), Right Panel (5) and
Center Panel (4).
b) Attach (3, 4 & 5) to Bottom Panel (2) via Wood Dowel and fasten with Screw (E). Use Allen Wrench (L)
to drive and tighten (E). Do not tighten (3 & 5) completely at this time. using Allen Wrench (L).
c) Locate pilot holes for Magnetic Catch (O) on Center Panel (4) and use Screw (Q) to fasten (O).
a) Insert Wood Dowel (C) into the designated hole at each end of Connect Bar (7).
b) Attach Connect Bar (7) to Side Panel and Center Panel (3, 5 & 4) as shown.
c) Tighten Screw (E) on bottom of Bottom Panel (2) completely to fasten (3 & 5) to Bottom Panel (2) fully.
C6 pcs
C8 pcs
E
C
2
L
7
C
C
E 6 pcs
5
4
3
x 2
7
7
3
4
5

STEP 6
8/12
STEP 5
Fit Back Panel (11) squarely between the Left, Right, Top and Bottom Panels and fasten with Screw (P).
B6 pcs
C 6 pcs
P 17 pcs
a) Insert Wood Dowel (C) into the inner 2 center holes at the top edge of Left Panel, Divide Panel and Right
Panel (3, 4 & 5).
b) Attach Top Panel (1) to (3, 4 & 5) via Cam-bolts and Wood dowels on the respective parts.
c) Insert Cam-lock (B) into the designated holes on (3, 4 & 5) then turn clockwise to lock onto Cam-bolt.
Refer to Page 5 for instructions on inserting and tightening Cam-lock.
B
C
5
4
3
11
P

P
2 pcs
2 pcs
R
P
R
3x12 mm
8
12
Hinge Cup
Hinge Well
STEP 8
9/12
STEP 7
4 pcs
K
D8 pcs
D
K
8 & 12
D8 pcs
D
a) Place the interior of Left Side Door (8) facing up as shown on a material that does not scratch or damage
the front surface.
b) Place Hinge (K) to fit the cup on the Door Wing into the hinge well on (8) and use Screw (D) to fasten
Door Wing.
c) Attach Magnetic Bar (P) to Door (8) and fasten with Screw (R).
d) Repeat Step a) to c) for Right Door (12).
a) Position Door (8 and 12) as shown.
b) Align the screw holes on the Frame Wing of the hinge to the pilot holes on Side Panel and fasten
with Screw (D).
D
K

STEP 10
10/12
STEP 9
Attach Knob (G) to Door using Knob Bolt (F).
F2 pcs
G 2 pcs
M2 pcs
N2 pcs
N
M
G
F
a) Drill two holes in the dry wall that are aligned to the two holes on the Connect Bar. The diameter of the hole
on the dry wall needs to fit the diameter of Plastic Anchor (N).
b) Press the Plastic Anchor (N) into the drilled hole in dry wall. Ensure that the anchor fits securely in the wall.
c) Drive Screw (M) through the screw hole on Connect Bar into Plastic Anchor to fasten the unit to the wall.
wall