Oxford Instruments Andor Sona 4.2B-11 Installation instructions

Sona & Marana
andor.com © Andor Technology Ltd. 2019.
Version 1.5 rev 4 Dec 2019
Hardware Guide
for Sona 4.2B-11, 2.0B-11
and Marana 4.2B-11 Models

version 1.5 rev 4 Dec 2019
2
Sona &
Marana
TABLE OF CONTENTS
SECTION 1: INTRODUCTION............................................................................................................. 10
1.1 TECHNICAL SUPPORT.......................................................................................................... 11
1.2 DISCLAIMER .......................................................................................................................... 12
1.3 COPYRIGHT AND PROTECTIVE NOTICES........................................................................... 12
1.4 TRADEMARKS AND PATENT INFORMATION....................................................................... 12
1.5 SUPPLIED COMPONENTS .................................................................................................... 13
1.5.1 Camera model options................................................................................................ 14
1.5.2 optional aCCessories .................................................................................................. 14
SECTION 2: PRODUCT OVERVIEW................................................................................................... 15
2.1 EXTERNAL FEATURES OF THE CAMERA ............................................................................ 15
2.2 REAR PANEL .......................................................................................................................... 16
2.3 POWER REQUIREMENTS ..................................................................................................... 17
SECTION 3: INSTALLATION ............................................................................................................... 18
3.1 TRANSPORT AND STORAGE INFORMATION ...................................................................... 18
3.2 USING THE LENS MOUNT .................................................................................................... 18
3.2.1 C-mount adaptor ....................................................................................................... 18
3.2.2 F-mount and t-mount adaptors ................................................................................... 19
3.3 USING A MAGNIFYING COUPLER UNIT (MCU) ................................................................... 19
3.4 MOUNTING THE CAMERA USING THE MOUNTING FLANGE ............................................ 19
3.5 CONNECTING THE CAMERA TO THE PC ............................................................................ 20
3.5.1 installing the usB 3 Card in the pC (iF required)........................................................ 20
3.5.2 ConneCting the Camera to the pCieCard ................................................................... 21
3.6 CONNECTING THE CAMERA TO THE POWER SUPPLY ..................................................... 21
3.7 CONNECTING A COOLING SYSTEM.................................................................................... 22
3.7.1 important Considerations when using liquid Cooling systems ...................................... 22
3.7.2 Cooling hose ConneCtors........................................................................................... 22
3.8 COOLANT RECOMMENDATIONS ......................................................................................... 23

version 1.5 rev 4 Dec 2019
3
Sona &
Marana
3.9 CONNECTING THE LIQUID COOLING SYSTEM .................................................................. 24
3.9.1 ConneCting the Coolant hoses ................................................................................... 24
3.9.2 disConneCting the Coolant hoses ............................................................................... 24
3.10 INSTALLING SOFTWARE AND USB DRIVERS ..................................................................... 25
3.10.1 minimum Computer requirements ................................................................................ 25
3.10.2 installing solis soFtware and usB drivers ................................................................ 25
3.10.3 new hardware wizard ................................................................................................ 25
3.10.4 installing the usB 3 (pCie) Card drivers ................................................................... 26
3.10.5 CheCking & setting Bios options (For pCsnot supplied By andor) ............................. 26
SECTION 4: OPERATION .................................................................................................................. 27
4.1 EMERGENCY MAINS DISCONNECTION .............................................................................. 27
4.2 POWER-UP SEQUENCE........................................................................................................ 27
4.3 POWER-DOWN SEQUENCE.................................................................................................. 27
4.4 USING THE SONA AND MARANA......................................................................................... 27
4.4.1 sCmos sensors ......................................................................................................... 27
4.4.2 extended dynamiC range (edr)................................................................................... 28
4.4.3 using rois(aois)....................................................................................................... 29
4.4.4 Binning........................................................................................................................ 29
4.4.5 spurious noise Filter .................................................................................................. 29
4.4.6 Blemish CorreCtion Filter ........................................................................................... 30
4.5 TRIGGER MODES .................................................................................................................. 30
4.6 SOFTWARE ACQUISITION EVENTS ..................................................................................... 31
4.7 ROLLING SHUTTER............................................................................................................... 31
4.7.1 rolling shutter meChanism ........................................................................................ 32
4.7.2 signal inFormation....................................................................................................... 32
4.7.3 timing parameters and external triggering ................................................................ 33
4.7.4 rolling shutter internal triggering (non-overlap mode) .......................................... 33
4.7.5 rolling shutter internal triggering (overlap mode) ................................................. 35
4.7.6 rolling shutter external / soFtware triggering (non-overlap mode) ....................... 36
4.7.7 rolling shutter external exposure triggering (non-overlap mode) .......................... 38
4.7.8 rolling shutter external exposure triggering (overlap mode) ................................. 39
4.7.9 rolling shutter external start triggering................................................................. 40
4.7.10 rolling shutter triggering Constraints ..................................................................... 40

version 1.5 rev 4 Dec 2019
4
Sona &
Marana
SECTION 5: MAINTENANCE.............................................................................................................. 41
5.1 REGULAR CHECKS ............................................................................................................... 41
5.2 ANNUAL ELECTRICAL SAFETY CHECKS ............................................................................ 41
5.3 GENERAL CLEANING & DECONTAMINATION INFORMATION............................................ 41
5.4 CLEANING THE CAMERA WINDOW..................................................................................... 41
5.4.1 tools required ........................................................................................................... 42
5.4.2 window Cleaning proCedure ....................................................................................... 42
5.5 FUSE REPLACEMENT ........................................................................................................... 42
5.6 COOLING HOSES AND CONNECTIONS............................................................................... 42
SECTION 6: TROUBLESHOOTING .................................................................................................... 43
6.1 PREVENTING CONDENSATION ............................................................................................ 43
6.2 QUICK TROUBLESHOOTING GUIDE.................................................................................... 44

version 1.5 rev 4 Dec 2019
5
Sona &
Marana
APPENDIX A: TECHNICAL SPECIFICATIONS................................................................................... 45
APPENDIX B: MECHANICAL DRAWINGS......................................................................................... 48
APPENDIX C: DEWPOINT INFORMATION ........................................................................................ 49
APPENDIX D: REFERENCE INFORMATION...................................................................................... 50
APPENDIX E: OTHER INFORMATION ............................................................................................... 51

version 1.5 rev 4 Dec 2019
6
Sona &
Marana
Revision HistoRy
Version Released Description
1.0 04 Sep 2018 Initial Release
1.1 11 Apr 2019 Updated USA and Asia-Pacic addresses
1.2 19 Jun 2019 Updated altitude information on page 46, updated backplate images and
mechanical drawings for Marana. USB terminology amended throughout.
1.3 29 July 2019 Updated China ofce address, table on page 39 and power supply information.
1.4 1 Aug 2019 Updated power supply information.
1.5 4 Dec 2019 Updated accessories table and model applicability of hardware guide.
Updates to tHe ManUal
Changes are periodically made to the product and these will be incorporated into new editions of the manual. Please
check for new releases of the manual in MyAndor: http://my.andor.com/login.aspx. If you nd an issue in this manual
please contact your customer support respresentative (Section 1.1) with a description of the issue.

version 1.5 rev 4 Dec 2019
7
Sona &
Marana
safety and WaRning infoRMation
READ THIS INFORMATION FIRST
1. If the equipment is used in a manner not specied by Andor, the protection provided by the equipment may be
impaired.
2. Before using the system, please follow and adhere to all warnings, safety, manual handling and operating
instructions located either on the product or in this Hardware Guide.
3. Users must be authorised and trained personnel only; otherwise this may result in personal injury, and/ or
equipment damage and impaired system performance.
4. There are no user-serviceable parts inside the product and the enclosure must not be opened. Only authorised
service personnel may service this equipment.
5. Do not position this product so that it is difcult to operate the Mains disconnecting device. See SECTION 4.1,
“Emergency Mains Disconnection”.
6. Protective earth is an integral part of the protection against electric shock in this product, and is provided via
the earth pin of the external power supply. Ensure that this is plugged into the building earth system via the
mains socket. Do not tamper with any of the earthing measures.
7. Only the correctly specied mains supply should be used.
8. Only the AC/DC external power supply provided with the product should be used.
9. Only the power supply cord provided with the product should be used. Should this not be correct for your
geographical area, contact your local Andor representative.
10. Make sure the power supply cord is located so that it will not be subject to damage. If replacement of the
detachable power supply cord is required, ensure replacement is of same type and rating.
11. Performance of the system may be adversely affected by rapidly changing environmental conditions or
operation outside of the operating conditions specied in “TECHNICAL SPECIFICATIONS”
12. While running an experiment, try to keep temperature as stable as possible.
13. This equipment has not been designed and manufactured for the medical diagnosis of patients.
14. Electromagnetic Compatibility: This is a Class B product.
15. This product has been designed and tested to perform successfully in a normal (basic) electromagnetic
environment, e.g. a typical life science test laboratory, as per the EU EMC Directive. It is not designed to
operate in a harsh electromagnetic environment, e.g. close to the following equipment: EMI/RFI generators,
electrostatic eld generators, electromagnetic or radioactive devices, plasma sources, arc welders, x-ray
instruments, intense pulsed sources, or other similar sources of high energy elds whose emissions are not
within the normal range expected under the EU EMC Directive.
16. Please note that this product is not designed to provide protection from ionising radiation. Any customer using
this product in such an application should provide their own protection.
17. Your product is a precision scientic instrument containing fragile components. Always handle it with care.
18. Do not wet or spill liquids on the product, and do not store or place liquids on the product.
19. If spillage occurs on the product, switch off power immediately, and wipe off with a dry, lint-free cloth.

version 1.5 rev 4 Dec 2019
8
Sona &
Marana
20. If any ingress of liquids has occurred or is suspected, unplug the mains cables, do not use, and contact Andor
Customer Support.
21. When using a liquid cooling system it is recommended that an overpressure device is tted to avoid leaks that
may nd their way to the mains electricity supply and create a hazard. Refer to the information in SECTION 3.7
for general guidelines on the correct installation and use of a liquid cooling system.
22. See SECTION 5.1, “Cleaning and Decontamination”.
23. Do not expose the product to extreme hot or cold temperatures.
24. Do not expose the product to open ames.
25. Do not allow objects to fall on the product.
26. Keep this hardware guide in a safe place for future reference.

version 1.5 rev 4 Dec 2019
9
Sona &
Marana
WaRning and safety labels
The following warning labels appear on the product:
There are no user serviceable components inside.
The serial label of the camera (above) is located on the back of the camera. It shows the product model, serial number
and the build date.
Unpacking infoRMation
Carefully unpack the unit and retain the packaging materials to transport or return equipment if required:
• If the equipment appears damaged in any way, return it to sales outlet in its original packaging.
• No responsibility for damage arising from the use of non-approved packaging will be accepted.
• Ensure all items and accessories specied at the time of ordering and as detailed on the packing list are
present: if any items are missing, please contact your sales representative.
• The camera has a shipping cover - remove before use and store in a safe place so it may be used at a future
time.

version 1.5 rev 4 Dec 2019
10
Sona &
Marana
SECTION 1: INTRODUCTION
This manual provides an overview of the Sona and Marana camera series. The Sona and Marana feature the latest
back-illuminated sCMOS sensor technology for an exceptional sensitivity, speed and eld of view. This makes it
particularly suitable for demanding applications - Sona for life science imaging: such as live-cell imaging, embryo
imaging; Marana for physical science imaging: such as space debris tracking and occultations. This manual includes a
description of the main features of the cameras, their installation, routine operation and troubleshooting. It also provides
a summary of some of the technical features of the Sona and Marana back-illuminated sCMOS camera series. For
further information on operation and control of the camera refer to the relevant software guide e.g. Solis, and to the
andor website for further technical information to help you get the best from your camera.
Figure 1: The Sona (left) and Marana (right) back-illuminated sCMOS Cameras

version 1.5 rev 4 Dec 2019
11
Sona &
Marana
1.1 tecHnical sUppoRt
If you have any questions regarding the use of this equipment, please contact the representative* from whom your
system was purchased, or:
Europe USA
Andor Technology Ltd.
7 Millennium Way
Springvale Business Park
Belfast
BT12 7AL
Northern Ireland
Tel. [phone]
Fax. [phone]
Andor Technology
300 Baker Avenue
Suite # 150
Concord
MA 01742
USA
Tel. [phone]
Fax. [phone]
Asia-Pacic China
Andor Technology (Japan)
5F IS Building
3-32-42 Higashi-Shinagawa
Tokyo 140-0002
Japan
Tel: [phone]
Fax: [phone]
Andor Technology (China)
Haitong Times Business Center,
Building B2 West,
No.11 West Third Ring North Road,
Haidian District,
Beijing,
100089
China
Tel: [phone]
Fax. [phone]
* The latest contact details for your local representative can be found on the Contact and Support page of our website.

version 1.5 rev 4 Dec 2019
12
Sona &
Marana
1.2 disclaiMeR
THE INFORMATION CONTAINED HEREIN IS PROVIDED “AS IS” WITHOUT WARRANTY, CONDITION OR
REPRESENTATION OF ANY KIND, EITHER EXPRESS, IMPLIED, STATUTORY OR OTHERWISE, INCLUDING BUT NOT
LIMITED TO, ANY WARRANTY OF MERCHANTABILITY, NON-INFRINGEMENT OR FITNESS FOR A PARTICULAR
PURPOSE.
IN NO EVENT SHALL ANDOR BE LIABLE FOR ANY LOSS OR DAMAGE, WHETHER DIRECT, INDIRECT, SPECIAL,
INCIDENTAL, CONSEQUENTIAL OR OTHERWISE HOWSOEVER CAUSED WHETHER ARISING IN CONTRACT, TORT
OR OTHERWISE, ARISING OUT OF OR IN CONNECTION WITH THE USE OF THE INFORMATION PROVIDED HEREIN.
1.3 copyRigHt and pRotective notices
The copyright in this document and the associated drawings are the property of Andor Technology Ltd. and all rights
are reserved. This document and the associated drawings are issued on condition that they are not copied, reprinted or
reproduced, nor their contents disclosed.
The publication of information in this documentation does not imply freedom from any patent or proprietary right of
Andor Technology Ltd. or any third party.
1.4 tRadeMaRks and patent infoRMation
Andor and the Andor logo are trademarks of Andor Technology Ltd. Andor Technology Ltd. is an Oxford Instruments
company. All other marks are property of their owners.
Manufacturers Information
Andor Technology Ltd., Belfast, BT12 7AL, UK.

version 1.5 rev 4 Dec 2019
13
Sona &
Marana
1.5 sUpplied coMponents
Description Quantity
Sona or Marana back illuminated sCMOS Camera
(model as ordered)
1
Software & Driver
CDs or Flash Drive
(Solis is ordered
separately)
1Hardware Guide in
electronic format 1
Power Supply
1 x 15 V 1Power Cord
(Country specic) 2
USB 3 Card 1Quick Start Guide 1
USB 3 Standard-A to
Standard-B cable 1Anti-static Wrist band 1
Multi timing
I/O cable 1Coolant pipes (hose inserts, pair) 1
Performance Sheet 1

version 1.5 rev 4 Dec 2019
14
Sona &
Marana
1.5.1 caMeRa Model options
There are a number of models of Sona and Marana camera based off of a common architecture and shared design (see
also Section 2.1). The differences for each model can be identied from the product codes and descriptions outlined
below:
Model Type Product Code Sensor Type Mounting
Sona 4.2B-11 SONA-4BV11 4.2 Megapixel Back-illuminated sCMOS:
VIS/NIR optimized
F-mount
Sona 2.0B-11 SONA-2BV11 2.0 Megapixel Back Illuminated sCMOS:
VIS/NIR optimized
C-mount
Marana 4.2B-11 MARANA-4BV11 4.2 Megapixel, Back-illuminated sCMOS:
VIS/NIR optimized
F-mount
Marana 4.2B-11 MARANA-4BU11
4.2 Megapixel, Back-illuminated sCMOS:
UV-optimized
F-mount
1.5.2 optional accessoRies
A range of accessories is available (see below). The Sona and Marana are intended only for use with accessories supplied and
recommended by Andor.
Description Code
MCU with 2x magnication for matching Sona to Leica microscopes MCU-SONA-LEI
MCU with x2 magnication for matching Sona to Nikon Ti Series (TiE and Ti2) microscopes MCU-SONA-NIK-TI
MCU with x2 magnication for matching Sona to Olympus microscopes MCU-SONA-OLY
C-mount - convert Sona 4.2B-11 to C-mount (for use with ROIs) ACC-MEC-11936
Re-circulator for enhanced cooling performance (supplied with 2x2.5 m tubing as standard) XW-RECR
Oasis 160 Ultra compact chiller unit (tubing to be ordered separately) ACC-XW-CHIL-160
6 mm tubing options for Oasis 160 Ultra compact chiller (2x2.5 m or 2x5 m lengths)
ACC-6MM-TUBING-2X2.5
ACC-6MM-TUBING-2X5M
Pair of barbed hose inserts for 6 mm tubing 6MM-HOSE-BARBS
Please contact your local Andor representative if further information is required.

version 1.5 rev 4 Dec 2019
15
Sona &
Marana
SECTION 2: PRODUCT OVERVIEW
This section provides an overview of the Sona and Marana. Please note that Sona conguration is shown below which
will also cover the Marana model. Please refer to the additional information supplied for details of any model specic
differences.
2.1 exteRnal featURes of tHe caMeRa
Figure 2: External Features (Sona model shown with F-mount)
Lens Mount
The Sona and Marana 4.2B-11 feature an F-mount as standard, the Sona 2.0B-11 model features a C-mount (other
adapters are available).
Sensor
The Sona and Marana feature high resolution sCMOS 2.0 and 4.2 Megapixel back illuminated sCMOS sensors. Andors
unique UltraVacTM vacuum technology has been utilised. UltraVac provides a permanent hermetically sealed enclosure
so that the QE and cooling performance can be maintained over many years operation.
Camera Window
There is a single AR coated UV grade silica window for optimum transmission. For more information on camera windows
please see http://www.andor.com/learning-academy/camera-windows-optimizing-for-different-spectral-regions.
Other Mountings
Four M4x 0.7 -6H, 8.0 [0.31] deep mounting holes on the front face (see section 3.4).
Lens
Mount
Sensor
Camera
Window

version 1.5 rev 4 Dec 2019
16
Sona &
Marana
2.2 ReaR panel
Figure 3: Rear Panel
USB Connectivity
USB 3 connection provides a robust high speed connection to the control PC.
External I/O: TTL / Logic
The TTL/Logic connection permits connection to other devices for synchronisation and control of re, trigger and shutter
operations. Connector type: D-type to BNC cable Fire (Output), External Trigger (Input), ARM.
Pinouts for the 15-way D type connector
Available using standard 3-way cable Available using optional 7-way cable
Pin 3-way cable Pin 3-way cable Pin 7-way cable Pin 7-way cable
1ARM 9Reserved 1ARM 9Reserved
2AUX_OUT_1 10 Reserved 2AUX_OUT_1 10 Reserved
3Reserved 11 Reserved 3FIRE n 11 Reserved
4Reserved 12 Reserved 4FIRE 12 Reserved
5Reserved 13 Reserved 5AUX_OUT_2 13 Reserved
6Ground 14 Reserved 6Ground 14 Reserved
7External Trigger 15 Reserved 7External Trigger 15 Reserved
8Reserved 8Spare
• External Trigger (and Spare inputs) are 5V TTL input. By default they trigger on a rising edge.
• ARM and AUX_OUT_1 (FIRE, FIRE n and AUX_OUT_2: for 7-way cable only) outputs are all TTL timing outputs. These can be
individually inverted via software (e.g. Solis or SDK).
• AUX_OUT_1 supplies the ‘FIRE ALL’ output by default. This is the logical AND of the FIRE pulses associated with Row #1 and
Row #n (the last row read out in the image frame). Therefore the FIRE ALL pulse represents the time within a frame when all
rows on the sensor are simultaneously exposing.
• AUX_OUT_1 is congurable for TTL timing outputs FIRE, FIRE n and FIRE ANY. The FIRE ANY pulse represents the time
within a frame when any row of the image frame is exposing. Refer to Section 2.6 for the behaviour of these signals and to the
SDK3 manual for conguring the AUX_OUT_1 output.
• AUX_OUT_2 output defaults to shutter control.
• Optional 7-way multi I/O timing interface cable (Andor part number ACC-ACZ-05612) gives access to all of the above I/O
functions shown in the table above right (excluding Ground and Reserved pins).
• Reserved pins should not be used.
ON/Off
Switch
USB 3
Type-B port Water Connections:
Compatible with tailpipes
for 1/4” bore soft PVC
hose (2 plcs)
Power Input Connection
External I/O

version 1.5 rev 4 Dec 2019
17
Sona &
Marana
* using optional 7-way multi I/O timing cable only
Liquid Cooling Connections
Liquid cooling connections provide the facility for connection to a liquid cooling system. Refer to Section 3.7.
Power Connector
Power input connection (15 V DC) for connection to the PSU. Refer to Section 2.3. An ON/OFF switch is also present.
Notes:
Minimum cable clearance required at rear of camera 150 mm.
2.3 poWeR ReqUiReMents
Ensure that the power connector for the camera is inserted securely. The connector is keyed to aid correct orientation. A
15 V DC External Power Supply supplies the camera. Refer to the Technical Specications for the External Power Supply
requirements.
NOTES:
1. The electrical mains lead should be certied for use in your country and in applicable countries the plug
must be tted with a 240 V 5 A fuse.
2. If users use any other power supply, they do so at their own risk.
Ext Trigger (and Spare*)Inputs
Arm (Fire*, Fire n*) and AUX_OUT Outputs
Camera
Camera
3.3V (5 V tolerant)
10K Ohms
> 2.0V
< 0.8V
> 1K Ohms
5V
> 2.4V Logic level 1
< 0.8V Logic level 0
Input triggers on
positive edge
10K Ohms

version 1.5 rev 4 Dec 2019
18
Sona &
Marana
SECTION 3: INSTALLATION
WARNINGS:
• PRIOR TO COMMENCING INSTALLATION, THE USER SHOULD REFER TO THE SAFETY AND WARNING
INFORMATION AND UNPACKING INSTRUCTIONS AT THE BEGINNING OF THIS MANUAL.
• DUE CARE MUST BE TAKEN WHEN LIFTING THE CAMERA. ENSURE THAT THE MOUNTING AND
CONNECTED ASSEMBLY IS SECURE AND ABLE TO SUPPORT THE WEIGHT OF THE CAMERA.
• POWER CABLING AND CONTROL CABLES SHOULD BE ROUTED TO PREVENT ACCIDENTS, DAMAGE AND
ACCIDENTAL UNPLUGGING WHILE AVOIDING BEND RADII OF LESS THAN 30 MM.
• TEMPERATURE AND HUMIDITY MUST MEET THE SPECIFICATIONS DEFINED IN TECHNICAL
SPECIFICATIONS.
3.1 tRanspoRt and stoRage infoRMation
• The camera is packed in a normal transport packaging for shipping.
• Allow the product to reach the ambient temperature after unpacking- especially if moving from a colder environment
to a warm environment as this may lead to condensation (see Section 6.1 for further information).
Storage
• Storage Temperature: -10°C to 50°C.
• If it is to be stored after use at a temperature below the coolant freezing point, ensure that all liquid coolant has been
expelled from the camera.
3.2 Using tHe lens MoUnt
An F-mount lens mounting system is present on the 4.2B-11 models, and a C-mount is present on the Sona 2.0B-11
model.
3.2.1c-MoUnt adaptoR
Note: C-Mount - Uses the inner set of mounting points
Removing the C-mount
1. Place the camera on its side (to prevent debris and dust landing on the window).
2. Use a 2mm hex key/driver to loosen the 4xM3 CSK (countersunk) screws.
3. Remove the 4 screws and carefully remove the C-mount from the faceplate.
Note: The use of nitrile gloves is recommended, when removing the C-Mount due to the proximity of the window.
Fitting the C-mount
1. Ensure that the faceplate is clean and free from debris.
2. Ensure that the o-ring is fully seated in the groove.
3. Locate the C-Mount part into the faceplate aligning the 4xM3 CSK screw holes.
4. Using the M3 CSK screws provided, tighten the mount to 1.1 Nm onto the faceplate.
Mounting
points (x4)

version 1.5 rev 4 Dec 2019
19
Sona &
Marana
3.2.2 f-MoUnt and t-MoUnt adaptoRs
Note: F-Mount and T-mounts- Use the inner set of mounting points (shown in section 3.2.1).
Removing the F/T-mount
1. Place the camera on its side (to prevent debris and dust landing on the window).
2. Use a 2mm hex key/driver to loosen the 4xM3 CSK (countersunk) screws.
3. Remove the 4 screws and carefully remove the F/T mount from the faceplate.
Figure 4: F-mount adaptor
Fitting the F/T-mount
1. Ensure that the faceplate is clean and free from debris.
2. Ensure that the o-ring is fully seated in the groove.
3. Locate the F/T-Mount part into the faceplate aligning the 4xM3 CSK screw holes.
4. Using the M3 CSK screws provided, tighten the mount to 1.1Nm onto the faceplate.
3.3 Using aMagnifying coUpleR Unit (McU)
A magnifying coupler (e.g. Andor MCU) or lens tube may be used to match the large
area sensor to the objective magnication and the aperture that is available from the
microscope. These attach to the camera using a T-mount style connection (described
in Section 3.2.2). For further information on the magnifying coupler please refer to the
instructions supplied with the MCU and your microscope.
3.4 MoUnting tHe caMeRa Using tHe MoUnting flange
The camera mounting face features 4 off M4x0.7 -6H tapped holes x8.0 [0.31] deep. These can
be used to secure the camera to an appropriate mounting as an alternative to using the C/F/T
lens mounts.
Note: that the weight of the camera is approx. 2.7 kg [5.95 lbs] ensure that the mounting
and the system it is connected to provides adequate support.
Locking tab
Alternative
Mounting points (x4)
magnifying
coupler
e.g. 1.5x
Microscope
specic
mount
Camera
mount

version 1.5 rev 4 Dec 2019
20
Sona &
Marana
3.5 connecting tHe caMeRa to tHe pc
The camera connects to a PC via USB 3 this provides a standard, robust and high speed connection with the control
PC. It is recommended to use the supplied USB 3 card as this will ensure consistent performance. Other USB ports on
the PC may share bandwidth with other devices and peripheral components. This may cause reduced, or inconsistent
performance.
3.5.1 installing tHe Usb 3 caRd in tHe pc (if ReqUiRed)
NOTE: Camera operation with PCIe cards not supplied by Andor cannot be guaranteed.
1. Unplug all cables from the rear of the computer.
Fasten the Card
to the slot
Unused ller brackets
Gently press the
card into the slot
PCIe 2.0 Slot
x4 recommended
2. Open the PC enclosure to gain access to the expansion slots.
3. Locate a suitable PCIe (2.0 or newer) slot:
• Card operates in an x1 slot or one with a greater number of channels (i.e. x4, x8 or x16).
4. If you are unsure which slot is correct, please consult the PC user manual.
5. Remove the ller bracket corresponding to the slot you intend to use.
6. Remove the controller card carefully from its protective ESD packaging and insert the card connector fully into
the expansion slot.
7. Ensure the card’s mounting bracket is ush with any other mounting or ller brackets to either side of it, then
secure the controller card in place.
8. Replace the computer cover and secure with mounting screws if applicable.
9. Reconnect any accessories you were using previously.