Ozito SDA-2100 User manual

CORDLESS
AUTO-LOADING
SCREWDRIVER
3.6V Lithium Ion
INSTRUCTION MANUAL
SPECIFICATIONS
Voltage: 3.6V
Driver Bit Size: 6.35mm (1/4”)
No Load Speed: 180/min
Max. Torque: 4Nm
Battery: 1.5Ah Li-ion (Integrated)
Charge Time: 3-5 Hours
Weight (tool only): 484g
SDA-2100
WHAT’S IN THE BOX
Cordless Screwdriver
Pre-Loaded Driver
Bits x 10
Charging Adaptor
Kit Bag
IN ORDER TO MAKE A CLAIM UNDER THIS
WARRANTY YOU MUST RETURN THE PRODUCT
TO YOUR NEAREST BUNNINGS WAREHOUSE WITH
YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO
RETURNING YOUR PRODUCT FOR WARRANTY
PLEASE TELEPHONE OUR CUSTOMER SERVICE
HELPLINE:
Australia 1800 069 486
New Zealand 0508 069 486
WARRANTY
TO ENSURE A SPEEDY RESPONSE PLEASE
HAVE THE MODEL NUMBER AND DATE OF
PURCHASE AVAILABLE. A CUSTOMER SERVICE
REPRESENTATIVE WILL TAKE YOUR CALL
AND ANSWER ANY QUESTIONS YOU MAY
HAVE RELATING TO THE WARRANTY POLICY
OR PROCEDURE.
OZITO Australia/New Zealand (Head Office) 1-23 Letcon Drive, Bangholme, Victoria, Australia 3175.
The benefits provided under this warranty are in addition
to other rights and remedies which are available to you at law.
Our goods come with guarantees that cannot be excluded
at law. You are entitled to a replacement or refund for a major
failure and for compensation for any other reasonably foreseeable
loss or damage. You are also entitled to have the goods repaired
or replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure.
Generally you will be responsible for all costs associated with
a claim under this warranty, however, where you have suffered
any additional direct loss as a result of a defective product you
may be able to claim such expenses by contacting our customer
service helpline above.
ozito.com.au
0816
3 YEAR REPLACEMENT WARRANTY
Your product is guaranteed for a period of 36 months from the
original date of purchase and is intended for DIY (Do It Yourself)
use only. If a product is defective it will be replaced in accordance
with the terms of this warranty. Lithium Ion batteries are covered
by a 12 month warranty. Warranty excludes consumable parts, for
example: driver bits, etc.
WARNING
The following actions will result in the warranty being void.
• If the tool has been operated on a supply voltage other
than that specified on the tool.
• If the tool shows signs of damage or defects caused
by or resulting from abuse, accidents or alterations.
• Failure to perform maintenance as set out within the
instruction manual.
• If the tool is disassembled or tampered with in any way.

ONLINE MANUAL
Scan this QR Code with your
mobile device to take you to
the online manual.
1 Bit Holder
2 LED Worklight
3 Bit View Window
4 Bit Cartridge
5 On/Off Trigger
6 Forward / Reverse Button
7 Charge Indicator LED
8 Charging Socket
9 Loading Switch
CORDLESS SCREWDRIVER
KNOW YOUR PRODUCT
1. CHARGING
1 Connect the charging adaptor
to the power supply.
2 Insert the charging jack into
the charging socket on the
screwdriver
3 The charge indicator light
will illuminate when properly
connected and charging.
10 Charging Adaptor
11 Charging Jack
12 Pre-Loaded Driver Bits x 10
ACCESSORIES
SETUP & PREPARATION
Note: It will take 4-5 charging cycles before the battery reaches
optimum charge and run time.
WARNING! THE TOOLS CHARGER IS RECOMMENDED
FOR USE WITH A RESIDUAL CURRENT DEVICE WITH
A RATED RESIDUAL CURRENT OF 30MA OR LESS.

2. LOADING A DRIVER BIT 3. CHANGING CARTRIDGE BITS
2 Slide the loading switch
forward so that the bit is
pushed into the bit holder.
2 Slide the loading switch
forward so that the bit is
pushed into the bit holder.
4 Slide the loading switch back
to retract the driver bit into
the cartridge.
2 Slide the loading switch
backward so that the bit
retracts from the bit holder.
1 Rotate the cartridge until the
required driver bit can be seen
through the view window.
Note: The cartridge will not rotate
unless the loading switch is
pushed back completely
1 Select the driver bit you wish to
remove or replace by rotating
the cartridge.
Note: The cartridge will not rotate
unless the loading switch is
pushed back completely
3 Pull the driver bit out of the bit
holder and replace with a new
bit.
The pre-loaded driver bits can be removed from the cartridge and
replaced with a different driver bit if desired.
1 Press down the loading switch
to allow the switch to slide.
Selecting and Loading Driver Bits Selecting and Loading Driver Bits
Unloading Driver Bits

SDA-2100
4. CONTROLS 5. SCREWDRIVING
OPERATION
1 To operate the screwdriver,
press the on/off trigger.
2 To stop operation, release the
on/off trigger.
The battery charge indicator will
illuminate when the on/off trigger
is pressed, indicating the level of
charge of the integrated battery.
1 For forward rotation, push the
forward/reverse button towards
the left side of the tool.
2 For reverse rotation, push the
forward/reverse button towards
the right side of the tool.
The work light will torn on when
the on/off trigger is pressed,
illuminating dark areas.
Note: The work light can be
turned on without the screwdriver
operation by pushing the forward/
reverse button into the middle
position.
Low State of Charge
(Battery Requires Charging)
Mid State of Charge
Full State of Charge
Forward / Reverse Button
Work Light
On/Off Trigger
Battery Charge Indicator
FWD
REV
2 Select the desired forward or
reverse driving direction.
4 Squeeze the on/off trigger to
start driving.
1 Select the required driver bit
and load into the bit holder.
Note: The cartridge will not rotate
unless the loading switch is
pushed back completely
3 Holdthescrewdriverrmlyand
place the bit on the screw to be
fastened.
5 Fasten the screw into the work
piece.
Note: Do not force the screwdriver
or apply side pressure to elongate
the hole. Let the tool do the work.
FWD
REV

MAINTENANCE
DESCRIPTION OF SYMBOLS
CARING FOR THE ENVIRONMENT
TROUBLESHOOTING
Power tools that are no longer usable should not be disposed of
with household waste but in an environmentally friendly way. Please
recycle where facilities exist. Check with your local council authority
for recycling advice.
Recyclingpackagingreducestheneedforlandllandrawmaterials.
Reuse of recycled material decreases pollution in the environment.
Please recycle packaging where facilities exist. Check with your
local council authority for recycling advice.
The screwdriver is not operating
Ensure that the forward/reverse button is pushed to the left of the tool for forward
rotation or pushed to the right for reverse rotation.
The battery could be depleted and requires charging. Connect the charger and
allow the battery to charge before operating.
Bit cartridge is not rotating
The loading switch may not be pushed backwards completely. Ensure that the
loading switch is pushed back and then rotate the cartridge.
Loading switch will not move
The bit cartridge may not be aligned properly. Try rotating the cartridge into
another position and then back into the desired place.
Spare parts can be ordered from the Special Orders Desk
at your local Bunnings Warehouse.
For further information, or any parts not listed here, visit
www.ozito.com.au or contact Ozito Customer Service:
Australia 1800 069 486
New Zealand 0508 069 486
E-mail: [email protected]
SPARE PARTS
THIS MANUAL CONTAINS IMPORTANT SAFETY AND OPERATING INSTRUCTIONS FOR YOUR BATTERY
CHARGER.
1. Before using the charger read all instructions and cautionary markings on the charger, battery pack and
the product using the battery pack.
2. This charger is not intended for any uses other than charging rechargeable batteries. Any other use may
resultinriskofre,electricshockorelectrocution.
3. Do not place any object on top of the charger or place the charger on a soft surface that may result in
excessive internal heat. Place the charger in a position away from any heat source.
4. To reduce risk of damage to the electric plug and cord, pull by the plug rather than the cord when discon-
necting the charger.
5. Make sure the cord is located so that it will not be stepped on, tripped over, or otherwise subjected to
damage or stress.
6. An extension cord should not be used unless absolutely necessary. Use of an improper extension cord could
resultintheriskofre,electricshockorelectrocution.
7. Do not operate the charger if it has received a sharp blow, been dropped or otherwise damaged in any
way. Have it checked by an electrician or power tool repairer.
8. Do not disassemble charger. Take it to an electrician or power tool repairer when service or repair is
required.Incorrectreassemblymayresultinariskofelectricshock,electrocutionorre.
9. To reduce risk of electric shock, unplug the charger from the outlet before attempting any cleaning.
Removing the battery pack will not reduce this risk.
10. Never attempt to connect 2 chargers together.
11. DO NOT store or use the tool and battery pack in locations where the temperature may reach or exceed 40ºC
(such as inside sheds or metal buildings in summer).
12. The charger is designed to operate on standard household electrical power (240 volts). Do not attempt to
use it on any other voltage!
13. The battery pack is not fully charged out of the carton. First read the safety instructions and then follow
the charging notes and procedures.
14. The longest life and best performance can be obtained if the battery pack is charged when the air tem-
perature is between 18 - 24ºC. Do not charge the battery pack in an air temperature below 10ºC or above
40ºC. This is important and will prevent damage to the battery pack.
15. Do not incinerate the battery pack even if it is seriously damaged or is completely worn out. The battery can
explodeinare.
16. Never attempt to open the battery pack for any reason. If the plastic housing of the battery pack breaks or
cracks, immediately discontinue use and do not recharge.
17. During charging, the battery must be placed in a well ventilated area.
BATTERY AND CHARGER SAFETY WARNINGS
1. When not in use, the screwdriver should be stored in a dry, frost
free location, keep out of children’s reach.
2. Keep ventilation slots of the screwdriver clean at all times.
3. If the housing of the screwdriver requires cleaning, do not use
solvents but cloth only.
4. Blow out the ventilation slots with compressed air periodically .
Note: Ozito Industries will not be responsible for any damage or
injuries caused by repair of the screwdriver by an unauthorised
person or by mishandling of the tool.
Warning
Read instruction manual
mA Milliamperes
Polarity
Thermal cut-out protection Transformer Energy
Rating (MEPS)
Double insulated
/min Revolutions or
reciprocation per minute
Ah Amp hour
Indoor use only
Nm Newton Meters
no No load speed
V Volts Hz Hertz
ac/~ Alternating current W Watts
Direct current
dc/
Wear eye protection
Wear ear protection
Regulator compliance mark
Diameter
mm Millimetres
Recycle battery Do not put in the rubbish
Do not incinerate Do not get battery wet
Lithium Ion battery Do not use or store battery in
temperatures exceeding 50ºC

SCREWDRIVER SAFETY WARNINGS
WARNING! When using mains-powered tools, basic safety precautions, including the
following, should always be followed to reduce risk of re, electric shock, personal injury
and material damage.
Read the whole manual carefully and make sure you know how to switch the tool off in an emergency, before
operating the tool.
Save these instructions and other documents supplied with this tool for future reference.
The electric motor has been designed for 230V and 240V only. Always check that the power supply
corresponds to the voltage on the rating plate.
Note: The supply of 230V and 240V on Ozito tools are interchangeable for Australia and New Zealand.
This tools charger is double insulated therefore no earth wire is required.
If the supply cord is damaged, it must be replaced by an electrician or a power tool repairer in order to avoid
a hazard.
Note: Double insulation does not take the place of normal safety precautions when operating this tool. The
insulation system is for added protection against injury resulting from a possible electrical insulation failure
within the tool.
Using an Extension Lead
Always use an approved extension lead suitable for the power input of this tool. Before use, inspect the
extension lead for signs of damage, wear and ageing. Replace the extension lead if damaged or defective.
When using an extension lead on a reel, always unwind the lead completely. Use of an extension lead not
suitableforthepowerinputofthetoolorwhichisdamagedordefectivemayresultinariskofreandelectric
shock.
To reduce the risk of electric shock, this products charger must be used with a residual current device (rated
at 30mA or less).
GENERAL POWER TOOL SAFETY WARNINGS - PERSONAL SAFETY
ELECTRICAL SAFETY
WARNING! Hold power tool by insulated gripping surfaces, when
performing an operation where the cutting accessory may contact hidden
wiring or its own cord. Cutting accessory contacting a “live” wire may make
exposed metal parts of the power tool “live” and could give the operator an electric
shock. Before drilling into walls, ceilings etc, ensure that there are no concealed
power cables or pipes in the cavity.
WARNING! Some dust created by power sanding, sawing, grinding,
drilling and other construction activities contain chemicals known to cause
cancer, birth defects or other reproductive harm. Some examples of these
chemicals are:
• Lead from lead-based paints
• Crystalline silica from bricks and cement and other masonry products
• Arsenic and chromium from chemically treated timber
Your risk from exposure to these chemicals varies, depending on how often you
do this type of work. To reduce your exposure to these chemicals: work in a well
ventilated area and work with approved safety equipment, such as dust masks that
arespeciallydesignedtolteroutmicroscopicparticles.
WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and
instructionsmayresultinelectricshock,reand/orseriousinjury.
Save all warnings and instructions for future reference. The term “power tool” in the warnings refers
to your mains-operated (corded) power tool or battery-operated (cordless) power tool.
1. Work area safety
a. Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b. Do not operate power tools in explosive atmospheres, such as in the presence of ammable
liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
c. Keep children and bystanders away while operating a power tool. Distractions can cause you to
lose control.
2. Electrical safety
a. Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power tools.Unmodiedplugsandmatchingoutletswill
reduce risk of electric shock.
b. Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
c. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the
risk of electric shock.
d. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase
the risk of electric shock.
e. When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a
cord suitable for outdoor use reduces the risk of electric shock.
f. If operating a power tool in a damp location is unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of electric shock.
3. Personal safety
a. Stay alert, watch what you are doing and use common sense when operating a power tool. Do
not use a power tool while you are tired or under the inuence of drugs, alcohol or medication. A
moment of inattention while operating power tools may result in serious personal injury.
b. Use personal protective equipment. Always wear eye protection. Protective equipment such as dust
mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce
personal injuries.
c. Prevent unintentional starting. Ensure the switch is in the off-position before connecting to
power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your
ngerontheswitchorenergisingpowertoolsthathavetheswitchoninvitesaccidents.
d. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may result in personal injury.
e. Do not overreach. Keep proper footing and balance at all times. This enables better control of the
power tool in unexpected situations.
f. Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
g. If devices are provided for the connection of dust extraction and collection facilities, ensure
these are connected and properly used. Use of dust collection can reduce dust-related hazards.
4. Power tool use and care
a. Do not force the power tool. Use the correct power tool for your application. The correct power
tool will do the job better and safer at the rate for which it was designed.
b. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be repaired.
c. Disconnect the plug from the power source and/or the battery pack from the power tool before
making any adjustments, changing accessories, or storing power tools. Such preventive safety
measures reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children and do not allow persons unfamiliar with the
power tool or these instructions to operate the power tool. Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and
any other condition that may affect the power tool’s operation. If damaged, have the power tool
repaired before use. Many accidents are caused by poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking
into account the working conditions and the work to be performed. Use of the power tool for
operations different from those intended could result in a hazardous situation.
5. Battery tool use and care
a. Recharge only with the charger specied by the manufacturer. A charger that is suitable for one
typeofbatterypackmaycreateariskofrewhenusedwithanotherbatterypack.
b. Use power tools only with specically designated battery packs. Use of any other battery packs
maycreateariskofinjuryandre.
c. When battery pack is not in use, keep it away from other metal objects, like paper clips, coins,
keys, nails, screws or other small metal objects, that can make a connection from one terminal
to another. Shortingthebatteryterminalstogethermaycauseburnsorare.
d. Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact
accidentally occurs, ush with water. If liquid contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irritation or burns.
6. Service
a. Have your power tool serviced by a qualied repair person using only identical replacement
parts. This will ensure that the safety of the power tool is maintained.