Ozito SDL-5000U User manual

CORDLESS
SCREWDRIVER
TORCH
3.6V Lithium Ion
ORIGINAL INSTRUCTIONS
SPECIFICATIONS
Voltage: 3.6V
Chuck Size: 6.35mm Magnetic
No Load Speed: 180/min
Torque Settings: 9
Max Torque: 3.5Nm
Battery: 1.5Ah Li-ion
Charge Time: 3 - 5Hours
Weight (tool only): 0.4kg
SDL-5000U
WHAT’S IN THE BOX
Cordless Screwdriver
Driver Bits x 24
USB Charging Cable
Docking Station
ozito-diy.co.uk
WARRANTY
OZITO UK Unit 9 Stadium Court, Wirral International Business Park, Plantation Road, Bromborough, Wirral, CH62 3QG 0616
All of our products undergo strict quality checks to ensure that they reach
you in perfect condition. In the unlikely event that your device develops a
fault, please contact our service department at the address shown on this
guarantee card. You can also contact us by telephone using the customer
service number shown. Please note the following terms under which
guarantee claims can be made:
1. These warranty terms regulate additional warranty services, which the
manufacturer mentioned below promises to buyers of its new products
in addition to their statutory guarantee claims are not affected by this
guarantee. Our guarantee is free of charge to you.
2. The warranty services only covers defects due to material or
manufacturing faults on a product which you have bought from the
manufacturer mentioned below are limited to either the rectication of said
defects on the product or the replacement of the product, whichever we
prefer.
Please note that our devices are not designed for use in commercial, trade
or professional applications. A guarantee contract will not be created if the
device has been used by commercial, trade or industrial business or has
been exposed to similar stresses during the guarantee period.
3. The following are not covered by our guarantee:
- Damage to the device caused by a failure to follow the assembly
instructions or due to incorrect installation, a failure to follow the operating
instructions (for example connecting it to an incorrect mains voltage or
current type) or a failure to follow the maintenance and safety instructions
or by exposing the device to abnormal environmental conditions or by lack
of care and maintenance.
- Damage to the device caused by abuse or incorrect use (for example
overloading the device or the use or unapproved tools or accessories),
ingress of foreign bodies into the device (such as sand, stones or dust,
transport damage), the use of force or damage caused by external forces
(for example by dropping it).
- Damage to the device or parts of the device caused by normal or natural
wear or tear or by normal use of the device.
4. Your Product is guaranteed for a period of 36 months from the original
date of purchase and is intended for DIY (Do It Yourself) use only. Lithium
Ion batteries and chargers are covered by a 12 month warranty. Warranty
excludes consumable parts. Guarantee claims should be submitted
before the end of the guarantee period within two weeks of the defect
being noticed. No guarantee claims will be accepted after the end of the
guarantee period. The original guarantee period remains applicable to the
device even if repairs are carried out or parts are replaced. In such cases,
the work performed or parts tted will not result in an extension of the
guarantee period, and no new guarantee will become active for the work
performed or parts tted. This also applies if an on-site service is used.
IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY YOU MUST
RETURN THE PRODUCT TO THE PLACE OF PURCHASE WITH YOUR
REGISTER RECEIPT.
Please refer to the restrictions of this warranty concerning wearing parts,
consumables and missing parts as set out in the service information in
these operating instructions.
CUSTOMER SERVICE HELPLINE
GB: 0151 294 4488
IRL: 1850 882711
Ozito-diy.co.uk

ONLINE MANUAL
Scan this QR Code with your
mobile device to take you to
the online manual.
1 Bit Holder
2 Torque Collar
3 LED Work Light
4 Forward / Reverse Lever
5 Handle Lock Button
6 Rotating Rear Handle
7 On / Off Trigger
8 USB Charging Point
9 Charge Indicator
10 Torch On/Off Switch
11 Torch LED
CORDLESS SCREWDRIVER / TORCH
KNOW YOUR PRODUCT
1. CHARGING
12 Drill Bit Storage
13 Docking Station
14 Charge Check Indicator
15 USB Charger Compartment
16 Clear Case Lock
17 USB Charging Cable
18 CRV Bits x 24
ACCESSORIES
SETUP & PREPARATION
1
12 13 14 15 16 17 18
2 3 7 8 9 10 11
5 64
Charging the Screwdriver / Torch
1 Remove the USB charging
adaptor from the base of the
docking station.
3 Plug the charging jack into
the charging point on the
screwdriver.
5 The charge indicator will
illuminate green once the tool
is completely charged.
2 Plug the USB
charging cable
into a USB
portable charge
pack (not
included) or USB
port.
4 The charge
indicator will
illuminate red
indicating
the battery is
charging.

2. DOCKING STATION 3. CHANGING DRIVER BITS
Charging with the Docking Station
1 Remove the USB charging
adaptor from the base of
docking station.
The docking station allows neat and tidy storage of the screwdriver bits,
while ensuring your screwdriver is always charged and ready to go.
3 Plug the charging jack into the
charging point on the docking
station.
5 The docking station indicator
lights illuminate in sequence,
indicating the tool is charging.
2 Plug the USB charging cable
into a USB portable charge
pack (not included) or USB
port.
4 Place the screwdriver / torch
onto the docking station to
allow the tool to charge.
6 When the tool is completely
charged, all 4 indicator lights
will illuminate.
Inserting Driver Bits
Removing Driver Bits
1 Insert the CRV bit directly into
the magnetic bit holder.
1 Pull the CRV bit out of
the magnetic bit holder to
remove.
2 Pull gently on the
CRV bit to ensure
it is properly
secured.

4. CONTROLS
OPERATION
On/Off Trigger Screwdriving LED Worklight
Using the Torch Function
Forward / Reverse Lever
Adjusting the Torque
1 To start driving, squeeze the
on/off trigger.
The screwdriver features a
worklight that will help brighten
the work area. This light will
automatically turn on once the on/
off trigger is pressed.
1 To turn the torch on, press
torch on/off switch into the on
position.
2 To stop driving,
release the on/off
trigger.
2 To turn the torch
off, press torch on/
off switch into the
off position.
1 Push the forward/reverse
lever left, for forward rotation.
2 For reverse rotation push the
lever to the right of the tool.
Align the arrow at the top of the
tool with the desired setting by
rotating the torque collar.
Note: A higher number will result
in higher torque or twisting
action.
Note: To avoid damaging screw heads, start with a low torque setting
and increase until the screw head is ush with the work piece.
FWD
REV
FWD

SDL-5000U
5. SWIVEL HANDLE 6. SCREWDRIVING
In-line Position
Angled Position
1 Hold the handle locking button
down.
The screwdriver / torch features a rotating handle to suit a range of
applications. You can operate the screwdriver of torch in either handle
position.
1 Select the desired handle
position.
4 Squeeze the on/off trigger to
start the screwdriver.
3 Hold the screwdriver rmly and place the bit on the screw to be
fastened.
1 Hold the handle locking button
down.
2 Rotate the handle
clockwise until it
clicks into position.
2 Check the
forward/reverse
lever is in the
desired setting.
5 Fasten the screw
into the work
piece.
Note: Do not force the screwdriver or apply side pressure to elongate
the hole. Let the screwdriver do the work.
2 Rotate the handle
anti-clockwise
until it clicks into
position.
FWD
REV
FWD

MAINTENANCE
TROUBLESHOOTING
On/Off Trigger is Locked
Ensure that the forward / reverse lever is in the correct position; pressed left for
forwards direction, pressed right for backwards direction. If it is in between the two
settings the on/off trigger will be locked.
LED Torch is Not Working
The tools battery may be depleted. Charge the tool using the USB charger
provided.
The Handle Is Not Rotating
Ensure you are holding the handle lock button down while rotating the handle.
Ensure you are rotating the handle in the correction direction. Clockwise rotation
into in-line position or anti-clockwise for angled position.
Tool is Not Charging When Placed Onto The Docking
Station
Ensure that you have connected the docking station to a suitable USB port using
the USB charging cable provided.
Ensure the tool is correctly seated in the docking station. SPARE PARTS
1. When not in use, the screwdriver should be stored in a dry, frost
free location, keep out of children’s reach.
2. Keep ventilation slots of the screwdriver clean at all times and
prevent any debris from entering.
3. If the housing of the screwdriver requires cleaning, do not use
solvents but cloth only.
4. Blow out the ventilation slots with compressed air periodically .
Note: Ozito Industries will not be responsible for any damage or
injuries caused by repair of the screwdriver by an unauthorised
person or by mishandling of the tool.
Spare parts can be ordered from the Special Orders Desk
at your local Bunnings Warehouse or Homebase store.
For further information, or any parts visit
www.ozito-diy.co.uk or contact Ozito Customer Service:
Great Britain: 0151 294 4488
Ireland: 1850 882711
E-mail: [e-mail]

DESCRIPTION OF SYMBOLS
THIS MANUAL CONTAINS IMPORTANT SAFETY AND OPERATING INSTRUCTIONS FOR YOUR
BATTERY CHARGER.
• To reduce risk of damage to the electric plug and cord, pull by the plug rather than the cord when
disconnecting the charger.
• Make sure the cord is located so that it will not be stepped on, tripped over, or otherwise subjected
to damage or stress.
• DO NOT store or use the tool in locations where the temperature may reach or exceed 40ºC (such as
inside sheds or metal buildings in summer).
• The tool is not fully charged out of the carton. First read the safety instructions and then follow the
charging notes and procedures.
• The longest life and best performance can be obtained if the tool is charged when the air tempera-
ture is between 18 - 24ºC. Do not charge the tool in an air temperature below 10ºC or above 40ºC.
This is important and will prevent damage to the tool.
• Do not incinerate the tool even if it is seriously damaged or is completely worn out. The battery can
explode in a re.
• Never attempt to open the tool for any reason. If the plastic housing of the tool breaks or cracks, im-
mediately discontinue use and do not recharge.
• During charging, the tool must be placed in a well ventilated area.
BATTERY AND CHARGER SAFETY WARNINGS
Warning Read instruction manual
mA Milliamperes
Polarity
Thermal cut-out protection
/min Revolutions or
reciprocation per minute
Ah Amp hour
Indoor use only
Nm Newton Meters
no No load speed
V Volts Hz Hertz
ac/~ Alternating current W Watts
Direct current
dc/
Isolation transformer

SCREWDRIVER SAFETY WARNINGS
GENERAL POWER TOOL SAFETY WARNINGS - PERSONAL SAFETY
WARNING! Some dust created by power sanding, sawing, grinding,
drilling and other construction activities contain chemicals known to cause
cancer, birth defects or other reproductive harm. Some examples of these
chemicals are:
• Lead from lead-based paints
• Crystalline silica from bricks and cement and other masonry products
• Arsenic and chromium from chemically treated timber
Your risk from exposure to these chemicals varies, depending on how often you
do this type of work. To reduce your exposure to these chemicals: work in a well
ventilated area and work with approved safety equipment, such as dust masks that
are specially designed to lter out microscopic particles.
WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and
instructions may result in electric shock, re and/or serious injury.
Save all warnings and instructions for future reference. The term “power tool” in the warnings refers
to your mains-operated (corded) power tool or battery-operated (cordless) power tool.
1. Work area safety
a. Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b. Donotoperatepowertoolsinexplosiveatmospheres,suchasinthepresenceofammable
liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
c. Keep children and bystanders away while operating a power tool. Distractions can cause you to
lose control.
2. Electrical safety
a. Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power tools. Unmodied plugs and matching outlets will
reduce risk of electric shock.
b. Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
c. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the
risk of electric shock.
d. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase
the risk of electric shock.
e. When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a
cord suitable for outdoor use reduces the risk of electric shock.
f. If operating a power tool in a damp location is unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of electric shock.
3. Personal safety
a. Stay alert, watch what you are doing and use common sense when operating a power tool. Do
notuseapowertoolwhileyouaretiredorundertheinuenceofdrugs,alcoholormedication. A
moment of inattention while operating power tools may result in serious personal injury.
b. Use personal protective equipment. Always wear eye protection. Protective equipment such as dust
mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce
personal injuries.
c. Prevent unintentional starting. Ensure the switch is in the off-position before connecting to
power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your
nger on the switch or energising power tools that have the switch on invites accidents.
d. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may result in personal injury.
e. Do not overreach. Keep proper footing and balance at all times. This enables better control of the
power tool in unexpected situations.
f. Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
g. If devices are provided for the connection of dust extraction and collection facilities, ensure
these are connected and properly used. Use of dust collection can reduce dust-related hazards.
4. Power tool use and care
a. Do not force the power tool. Use the correct power tool for your application. The correct power
tool will do the job better and safer at the rate for which it was designed.
b. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be repaired.
c. Disconnect the plug from the power source and/or the battery pack from the power tool before
making any adjustments, changing accessories, or storing power tools. Such preventive safety
measures reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children and do not allow persons unfamiliar with the
power tool or these instructions to operate the power tool. Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and
any other condition that may affect the power tool’s operation. If damaged, have the power tool
repaired before use. Many accidents are caused by poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking
into account the working conditions and the work to be performed. Use of the power tool for
operations different from those intended could result in a hazardous situation.
5. Battery tool use and care
a. Rechargeonlywiththechargerspeciedbythemanufacturer.A charger that is suitable for one
type of battery pack may create a risk of re when used with another batery pack.
b. Usepowertoolsonlywithspecicallydesignatedbatterypacks.Use of any other battery packs
may create a risk of injury and re.
c. When battery pack is not in use, keep it away from other metal objects, like paper clips, coins,
keys, nails, screws or other small metal objects, that can make a connection from one terminal
to another. Shorting the battery terminals together may cause burns or a re.
d. Under abusive conditions, liquid may be ejected from the battery; aviod contact. If contact
accidentallyoccurs,ushwithwater.Ifliquidcontactseyes,additionallyseekmedicalhelp.
Liquid ejected from the battery may cause irritation or burns.
6. Service
a. Haveyourpowertoolservicedbyaqualiedrepairpersonusingonlyidenticalreplacement
parts. This will ensure that the safety of the power tool is maintained.

size 445 x 210 mm
Danger! - Read the operating instructions to re-
duce the risk of inquiry
Caution! Wear ear-mus. The impact of noise
can cause damage to hearing.
Caution! Wear safety goggles. Sparks gene-
rated during working or splinters, chips and dust
emitted by the device can cause loss of sight.
The reprinting or reproduction by any other me-
ans, in whole or in part, of documentation and
papers accompanying products is permitted only
with the express consent of the iSC GmbH.
Subject to technical changes
SDL-5000U
GB Additonal operating & safety instructions Screwdriver / Torch
Service information
We have competent service partners in all countries named on the guarantee certicate whose contact
details can also be found on the guarantee certicate. These partners will help you with all service re-
quests such as repairs, spare and wearing part orders or the purchase of consumables.
Please note that the following parts of this product are subject to normal or natural wear and that the
following parts are therefore also required for use as consumables.
Category Example
Wear parts* Drill chuck, Battery
Consumables* Bit inserts/drill bits
Missing parts
* Not necessarily included in the scope of delivery!
In the eect of defects or faults, please register the problem on the internet at www.isc-gmbh.info. Plea-
se ensure that you provide a precise description of the problem and answer the following questions in all
cases:
• Did the equipment work at all or was it defective from the beginning?
• Did you notice anything (symptom or defect) prior to the failure?
• What malfunction does the equipment have in your opinion (main symptom)?
Describe this malfunction.
Yang/Product-ManagementWeichselgartner/General-Manager
- 135 -
explains the following conformity according to EU directives and norms for
the following product
Screwdriver / Torch SDL-5000U (Ozito)
2014/29/EU
2005/32/EC_2009/125/EC
2014/35/EU
2006/28/EC
X2014/30/EU
2014/32/EU
2014/53/EC
2014/68/EU
90/396/EC_2009/142/EC
89/686/EC_96/58/EC
X2011/65/EU
X2006/42/EC
Annex IV
Noti ed Body:
Noti ed Body No.:
Reg. No.:
2000/14/EC_2005/88/EC
Annex V
Annex VI
Noise: measured LWA = dB (A); guaranteed LWA = dB (A)
P = KW; L/Ø = cm
Noti ed Body:
2004/26/EC
Emission No.:
Standard references: EN 60745-1; EN 60745-2-2; EN 55014-1; EN 55014-2;
Landau/Isar, den 14.06.2016
First CE: 16 Archive-File/Record: NAPR014308
Art.-No.: 44.722.36 I.-No.: 11016 Documents registrar: R. Gehard
Subject to change without notice Wiesenweg 22, D-94405 Landau/Isar
ISC GmbH · Eschenstraße 6 · D-94405 Landau/Isar
Declaration of conrmity

size 445 x 210 mm
Items supplied
Please check that the article is complete as
specied in the scope of delivery. If parts are
missing, please contact our service center or the
sales outlet where you made your purchase at
the latest within 5 working days after purchasing
the product and upon presentation of a valid bill
of purchase. Also, refer to the warranty table in
the service information at the end of the operating
instructions.
• Open the packaging and take out the equip-
ment with care.
• Remove the packaging material and any
packaging and/or transportation braces (if
available).
• Check to see if all items are supplied.
• Inspect the equipment and accessories for
transport damage.
• If possible, please keep the packaging until
the end of the guarantee period.
Danger!
The equipment and packaging material are
not toys. Do not let children play with plastic
bags, foils or small parts. There is a danger of
swallowing or suocating!
Proper use
The cordless screwdriver is designed for tigh-
tening and removing screws.
The equipment is to be used only for its prescri-
bed purpose. Any other use is deemed to be a
case of misuse. The user / operator and not the
manufacturer will be liable for any damage or inju-
ries of any kind caused as a result of this.
Please note that our equipment has not been de-
signed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
machine is used in commercial, trade or industrial
businesses or for equivalent purposes.
Technical data
Motor power supply: .............................. 3.6 V DC
Idling speed: ............................................180/min
Clockwise/counter-clockwise: ........................Ye s
Battery charge voltage: .............................5V DC
Charging time: ...................................... 3-5 hours
Battery capacity ......................................... 1.5 Ah
Battery type: ................................................Li-ion
Danger!
Sound and vibration
Sound and vibration values were measured in
accordance with EN 60745.
LpA sound pressure level ..................... 57.9 dB(A)
KpA uncertainty ............................................. 3 dB
LWA sound power level ....................... 68.9 dB(A)
KWA uncertainty ............................................. 3 dB
Wear ear-mus.
The impact of noise can cause damage to hea-
ring.
Total vibration values (vector sum of three direc-
tions) determined in accordance with EN 60745.
Vibration emission value ah= 0.72 m/s2
K uncertainty = 1.5 m/s2
The specied vibration value was established in
accordance with a standardized testing method. It
may change according to how the electric equip-
ment is used and may exceed the specied value
in exceptional circumstances.
The specied vibration value can be used to
compare the equipment with other electric power
tools.
The specied vibration value can be used for initi-
al assessment of a harmful eect.
Keep the noise emissions and vibrations to a
minimum.
• Only use appliances which are in perfect wor-
king order.
• Service and clean the appliance regularly.
• Adapt your working style to suit the appliance.
• Do not overload the appliance.
• Have the appliance serviced whenever
necessary.
• Switch the appliance off when it is not in use.
• Wear protective gloves.
Caution!
Residual risks
Even if you use this electric power tool in ac-
cordance with instructions, certain residual
risks cannot be rules out. The following ha-
zards may arise in connection with the equip-
ment’s construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protecti-
on is used.
3. Health damage caused by hand-arm vibra-
tions if the equipment is used over a pro-
longed period or is not properly guided and
maintained.
For EU countries only
Never place any electric power tools in your
household refuse.
To comply with European Directive 2012/19/EC
concerning old electric and electronic equipment
and its implementation in national laws, old elec-
tric power tools have to be separated from other
waste and disposed of in an environment-friendly
fashion, e.g. by taking to a recycling depot.
Recycling alternative to the return request:
As an alternative to returning the equipment to
the manufacturer, the owner of the electrical
equipment must make sure that the equipment
is properly disposed of if he no longer wants to
keep the equipment.The old equipment can be
returned to a suitable collection point that will
dispose of the equipment in accordance with the
national recycling and waste disposal regulations.
This does not apply to any accessories or aids
without electrical components supplied with the
old equipment.
This consignment contains lithium-ion batteries.
In accordance with special provision 188 this
consignment is not subject to the ADR regula-
tions. Handle with care. Danger of ignition in case
of damage to the consignment package. If the
consignment package is damaged: Check and
if necessary repackage. For further information
contact: 0049 1807 10 20 20 66 (xed network
14 ct/min, mobile phone max. 42 ct/min) Outside
Germany charges will apply instead for a regular
call to a landline number in Germany.