Ozito AGG-310 User manual

DESCRIPTION OF SYMBOLS SPARE PARTS
AIR GREASE
GUN
410g
INSTRUCTION MANUAL
SPECIFICATIONS
AGG-310
Chamber Capacity: 410g
Chamber Length: 280mm
Operating Pressure: 30-90psi (2.0-6.2Bar)
Average Air Consumption: 113L/min (4cfm)
Grease Outlet Pressure: 900-2700psi (60-190Bar)
Air Inlet: 1/4” BSP
Hose Diameter: ø9.5mm (3/8”)
Weight: 1.45kg
Spare parts can be ordered from the Special Orders
Desk at your local Bunnings Warehouse.
For further information, or any parts not listed here, visit
www.ozito.com.au or contact Ozito Customer Service:
Australia 1800 069 486
New Zealand 0508 069 486
Email: [email protected]
WARNING!
Using an Extension Hose
Always use an approved extension hose suitable for the air input of this tool. Before use, inspect the hose for
signs of damage, wear and ageing. Replace the extension hose if damaged or defective.
When using an hose on a reel, always unwind the lead completely.
It is recommended that the hose is a maximum of 25m in length.
NEVER under any circumstances aim the nozzle at another person or animal.
• In the event of an injury occurring, seek medical advice immediately.
• Always ensure there is adequate ventilation when using the grease gun.
• The use of ear protection is recommended.
• Eye protection is recommended to keep hazardous material, vapours and liquids out of eyes.
•Always wear a face mask when using the grease gun.
• Never immerse the grease gun in liquid.
GENERAL AIR TOOL SAFETY WARNINGS
AIR GREASE GUN SAFETY WARNINGS
WARNING! Read all safety warnings and all instructions. Failure to follow the
warnings and instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference. The term “power tool” in the warnings refers to
your mains-operated (corded) power tool or battery-operated (cordless) power tool.
1. Work area safety
a. Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b. Do not operate power tools in explosive atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools create sparks which may ignite the dust
or fumes.
c. Keep children and bystanders away while operating a power tool. Distractions can
cause you to lose control.
d. Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing
and gloves away from moving parts. Loose clothes, jewellery or long hair can be
caught in moving parts.
e. Check the maximum pressure rating of any tools or accessories that you intend using with
the compressor. The output pressure of the air from the compressor must be regulated so
that it never exceeds the rated pressure of the tool or accessory.
f. Always wear safety goggles or glasses when using the air compressor. Never point the
nozzle of an accessory towards any part of your body or towards another person.
g. Drain the moisture from the tank daily. It will help prevent corrosion.
h. Use safety equipment including safety goggles or shield, ear protection, breathing respirator mask and
protective clothing.
i. Air tools should not be used in a potentially explosive environment.
j. Use safety equipment including safety goggles or shield, ear protection, breathing or
respirator mask and protective clothing.
k. The tool must be used only for its prescribed purpose. Any use other than those mentioned
in this Manual will be considered a case of misuse. The user and not the manufacturer
shall be liable for any damage or injury resulting from such cases of misuse.
WARNING! In the event that an air line is cut or broken, the air supply must be turned off
at the compressor. A broken air line which is not supported is extremely dangerous and can whip around very
quickly, both with the capability of striking people, and blowing foreign particles into the air.
Do not attempt to catch the air line but immediately keep bystanders well clear and turn off the air supply to the
hose, turn off the compressor at the On / Off button, and then remove the hose from the compressor.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given the supervision or
instruction concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
Warning Read instruction
manual
Wear eye protection
and breathing mask
Cubic feet per minute
Wear ear protection
Litres per minute
L/min cfm
NEVER allow children to operate or play with the grease gun.
• Before cleaning, always disconnect the appliance from the air supply.
• Always disconnect from air supply when refilling the grease container.
• After every use ensure you clean your grease gun thoroughly.
NEVER use the grease gun outside when it is raining.
1 Nozzle
2 Bleed Valve
3 Grease Gun
4 Trigger
5 Quick Connector (air inlet)
6 Plunger Release
7 Rigid Spout
8 Flexible Spout
9 Grease Chamber
10 Plunger Handle
KNOW YOUR PRODUCT
10
6
78
9

TROUBLESHOOTINGMAINTENANCE
If the grease gun fails to work effecvely, perform the
following checks:
• Check the air inlet is free of any dirt or blockages.
• Ensure the grease gun is lubricated properly.
• Check that the pressure on the air compressor is within its
||working range. If not, let the compressor rest to
||re-pressurise / refer to the compressor instruction manual.
• Check plunger has been released
• Check grease level in chamber
• Check for blockages or leaks
Note: Operang Pressure range is 30 - 90psi (2 - 6.2Bar). Ensure your compressor is set no higher than 90psi (6.2Bar)
Note: This tool should be connected to a clean, dry air supply with inline oiler and water seperator.
• If the enclosure of the gun requires cleaning, do not use
solvents but a moist soft cloth only. Never let any liquid get inside
the gun; never immerse any part of the gun into a liquid.
• If the tool is used for long periods ar a time, a combined
filter/lubricator must be fitted. Air filter must be fitted at all times.
• Store the tool in a dry and safe place out of reach of children.
• Oil the grease gun after each use.
CONNECTING TO COMPRESSOR
OPERATION
FILLING THE GREASE GUN
2. Screw the male nio fing clockwise
into the female end of the air inlet.
3. Pull back the sleeve on hose fing, insert
male end & release sleeve on hose fing.
1. Wrap the threaded male end of an
air fing with thread seal tape in a
clockwise direcon.
Aaching a spout to a grease nipple
1. Ensure the grease nipple is clean.
2. Connect the required spout by screwing the
threaded end into the grease gun.
3. Firmly press the other end of the spout
against grease nipple and dispense grease
Aer Filling, remove any air pockets in the grease chamber.
1. Disconnected the tool from the air supply.
2. Release the plunger by depressing the plunger release.
3. Unscrew the chamber slightly by one and a half turns.
4. Draw back the plunger handle fully.
5. Press the plunger release mechanism
6. Reghten the grease chamber
7. Depress the air bleed valve several mes to let air escape.
Filling from a container.
1. Unscrew the grease chamber.
2. Pull the handle back so that it is fully extended.
3. Use a spatula to pack the grease into the chamber.
4. Once filled, clean excess from the edge of the chamber.
5. Screw the chamber to securely back onto the gun.
6. Press the plunger release mechanism.
Note: Be careful not to accidentally press
the relase mechanism whilst filling.
Installing a cartridge.
1. Unscrew the grease chamber.
2. Pull the handle back so it is fully extended.
3. Remove the packaging from the cartridge.
4. Insert the cartride fully into the chamber.
5. Screw the chamber back into the gun.
6. Press the pluger release mechanism.
Operaon
1. Connect to suitable air supply
2. Pull trigger to dispense grease from the spout
3. When finished. Disconnect from air supply
Note: Disconnect the tool from the air supply before fing or removing aachments.
Filling from a grease filler pump
1. Pull the handle back so it is fully extended.
2. Hold the grease gun vercally and connect
the plug of a filler pump to the gun nozzle.
3. Operate the filler pump to load the grease.
4. Stop pumping when grease is loaded.
5. Disconnect the filler plug, clean the filler
pump nozzle and press the plunger release.
Note: Pulling back on the plunger handle slightly will make pressing the plunger relase mechanism easier.