Ozone MORPHY NXT PLUS User manual

1
OZ-FDL-01 LIFE NXT PLUS
DOWNLOAD NOW
OzoLife iOS OzoLife Android
OzoLife
EMAIL ID: [email protected] | CUSTOMER CARE: [phone]
WWW.OZONESECUTECH.COM
USER MANUAL
MORPHY NXT PLUS
SMART DOOR LOCK
Fingerprint Password Emergency
Key
RFID CardOzoLife
Mobile App
Z
O
O

1
INDEX
Introduction
Installation
Product Feature
Operation
App Feature & Add Lock
FAQ
Notes
Warranty Card
6-7
4
5
2-3
8-9
10
11-12
13-14

2INTRODUCTION OPERATION FAQ APPENDIX
INTRODUCTION
1.1 LOCK STRUCTURE
Please keep internal/external panel clean before installation.
Battery
Battery Charging
Interface
Quick Open Button
Emergency Knob
Night Latch Knob
Unlock Button
Reset RESET
Lock Button
Lock Button
Keypad
RFID Scanner
Lock Button
Key Cover
Bell
Key Hole
MicroUSB
external power port
OPEN CLOSE
1 2 3
4 5 6
78
0
9

3INTRODUCTION OPERATION FAQ APPENDIX
Battery cover
Door Front panel parts
Back panel
parts
Back panel parts
Data line
Quick open button
Handle spring
Spindle
Emergency knob
Cylinder
Night Latch Knob
Unlock button
Lock button
Panel screw(cut
when necessary)
Panel screw
(cut when
necessary)
Lock body
screw
Cylinder screw
Guide post
Installation
Screw
10~30mm
15~20mm
Cylinder and
core should
be 15-20mm
protruding door
panel
Spindle length
should be
10-30mm
protruding door
panel

4INTRODUCTION OPERATION F&Q APPENDIX
PANEL AND LOCK BODY INSTALLATION STEPS
1
2
3
Adjust latch direction according to door opening side.
Lock body and cylinder installation: Put lock body into the hole made and then tighten the
screw, put cylinder into lock bodyguard hole after that tighten cylinder screw.
a) Put stud and guidepost on front panel parts and tighten it, at the same time put spring
into back panel square hole, cut spindle, and lock core when necessary.
b) Take data line from above lock body into the inside door, front panel should be
tightened on the door.
c) Take back mounting panel accessory and washer onto the door (mind data line should go
through mounting panel), use panel installation to tighten step by step.
d) Put spindle with spots into lock body square hole and make sure the lock body is
perpendicular to the spindle, adjust mounting panel accessory position to match mounting
plate, cylinder and cylinder hole should be at the same line, then tighten screw-on
mounting plate.
e) Connect data line to back panel, put extra data into door leaf, spindle, cylinder core and
knob should fall into the corresponding position, tighten back panel onto the door with\
the screw.
f) Try the quick open handle, pull at the same time rotate clockwise and counter-clockwise,
turn the emergency knob, night latch knob to see if it works smooth, otherwise adjust follow
step D.
g) Install battery and battery cover, press lock and unlock button, use fingerprint unlock
(if can not reset), press * for lock, original pin code is 00000000 and try to open by card or
key open, once ok mean install well.
Panel Installation
INSTALLATION

After installing the lock, please reset factory default and clear all fingerprints.
1
The handle is the main part of the lock; please do not hang anything on the handle to
avoid the handle twisting smoothly.
2
When registering the fingerprint, please avoid too hard pressing the finger window as it
can cause damage to the finger window.
3
The batteries should not be used for a long duration. It is generally recommended to change
the batteries at least every six-month, otherwise battery leakage can damage the smart lock.
Lock uses lithium batteries when first time heard “low battery, please change battery” still
can use around 50 times, to avoid any inconvenience cause please change your batteries
when necessary.
4
5
After 5 times wrong fingerprint, card or code being inserted continuous lock will be locked
for 90 seconds.
6
Remark:
PRODUCT FEATURES
5INTRODUCTION OPERATION F&Q APPENDIX
●Way to open: Fingerprint, Password, IC card, Key and combination.
(refer to actual product)
●Fingerprint: Advanced semiconductor sensors, 360 degrees identification angle, finger
sensor size 160*160, 508 dpi resolution and effectively false fingerprint
(FRR <1%,FAR<0.00001%)
●Pin code: Fashionable touch screen technology, before correct password can input 12
digital which can avoid password peeping.
●Double open mode: Double fingerprint mode (master + common user), fingerprint +
password mode, fingerprint + card mode, after setting only two users can verify at the same
time to open the door, suitable for special occasions.
●Master /User management: Master has the right to settle down user, and user fingerprint
only can open door. The lock can settle down master 9pcs (can be a fingerprint, code and
card but in total 9), fingerprint, code, and card capacity 300.
●Door Bell: When lights on can be used as 0, lights off can be used as a bell.
●1 Button Lock Function: With the light on *used as*, without the light on is lock button.
●Alarm: Tamper, low battery alarm, and password protection (with app function can
get door open recorder).
● External power supply: Can use a power bank or other equipment with 5V for emergency
power supply.

1
2
RESET FACTORY DEFAULT:
Press RESET at the back of the lock for 6 seconds; voice will prompt reset success.
LOCK PARAMETER SETTINGS:
Press “888#” to enter lock parameter setting menu.
1ADMINISTRATOR SETTING
Touch screen for lights on and long press # (need verify master for further settle down)
verify any master register - Press 1 for add master.
2USER SETTING
Touch screen for lights on and long press # (need verify master for further settle down) verify
any master register - Press 2 for adding the user.
Motor torque setting: Enter into parameter setting - Press 1 for motor torque setting and
press 1 again for high, 2 for medium and 3 for small.
1.1 Register master: After confirming master- press 1 for adding master (master can add
fingerprint, code or card), for fingerprint you need to confirm it 5 times, for code you need to
enter 8 digits 2 times and # for confirm, for card you need to confirm 1 time only, * for the exit.
2.1 Register user: After confirming master-press 1 for add user (user can add fingerprint, code or
card), for fingerprint you need to confirm 5 times, for code you need to enter 8 digits 2 times
and # for confirm, for card you need to confirm 1 time only, * for the exit.
1.2 Delete register master(fingerprint/card/code): After confirm master - Press 2 for delete
master, input code of master and press # for confirm (eg:003) delete after succeed,
press * for the exit.
Open way setting: Enter into the master setting - Press 2 for open way, can change from
L to R or R to L.
3Motor reversal time setting: Enter into the master setting - Press 3 for motor reversal setting,
press 2 for add 0.1 second, 8 for less 0.1 seconds (can adjust from 0-0.3 second).
4Self elastic lock body setting: Enter into master setting - Press 4 for self elastic lock body
setting, swift from self elastic and non self elastic lock body.
6
Can not delete all master
1
Remark:
INTRODUCTION OPERATION F&Q APPENDIX
OPERATION

3SYSTEM SETTING:
Touch screen for lights on and long press # (need verify master for further settle down)
verify any master register - Press 3 for system setting.
2.2
7
4FACTORY DEFAULT:
Touch screen for lights on and long press # (need verify master for further settle down) verify
any master register —press 4 for factory default—input correct master and # for confirm.
5INFORMATION CHECKING:
Touch screen for lights on and long press # (need verify master for further settle down) verify
any master register - Press 5 for information checking.
Delete register user (fingerprint/card/code): After confirm master - Press 2 for delete user,
input code of user and press # for confirm( eg:003) delete after succeed press * for exit.
3.1 Time: After getting into system settle down press 1 for time: Follow year (eg: 2020 also can
say 20)/month/date/hour/minute/ # for confirm.
3.2 Lock code settle down: After getting into system settle down press 2 then lock code press #
for confirm.
3.3 Voice settle down: After getting into system settle down press 3 for voice volume (6 for louder
4 for smaller).
5.1 Time checking: After entering information checking, press 1 for time checking - input time and
press # for confirmation.
5.2 Code checking: After entering information checking, press 2 for code checking and press #
for confirm.
5.3 Space checking: After entering information checking, press 3 for space checking, voice will
promote: how many fingerprints have been registered, how code been to register and how many
cards can been register and left how many.
3.4 Open mode settle down: After getting into system settle down press 4 then press 1 for single
open way, 2 for double open way, 3 for lock time.
3.5 Automatic lock setting: Press 5 to enter automatic lock setting sub-menu, Press 2 to increase
& Press 8 to decrease automatic lock delay time by 1 second.
INTRODUCTION OPERATION F&Q APPENDIX

1
2
Unlocking record:
Unlock way+ unlock ID +timing; User can check record from App for 12 months.
Offline record supplementary biography:
After online, the device will upload offline records to the cloud.
1
2
Search OzoLife app from the App store and register.
Open App and access it and follow below way add lock (Auto connection/add manually)
Auto connection.
4Time synchronization:
Lock time and server keep same, support global time zone + winter/summer time switch.
5Hijack alarm:
Can settle down fingerprint, password, and card to be coercion information, by using coercion
information can get hijack information.
3Alarm:
Low battery, wrong password, wrong fingerprint, wrong card and anti prying alarm etc...
APP FEATURE
ADD LOCK
INTRODUCTION OPERATION F&Q APPENDIX
8

3Add Manually
4Long press # then press 1, enter into manage then press 3 for network setting and last
press 1 for connecting.
9
1
2
After adding temporary code, need to try on lock then finished.
Max. Support 10 groups of code, and code can be edited or deleted.
3Temporary codes can be settled down by period.
4Dynamic code: Can get from the dynamic code page.
5Remote unlocking: Press bell sign trigger remote unlocking request, app response
unlocks or refuse.
           INTRODUCTION OPERATION F&Q APPENDIX
ADD TEMPORARY CODE SETTING

How to read operation records?
1
Select “Opening record” option on lock main interface
How to associate app user account with lock user number?
2
Open “Record” option on lock interface in App, select log record for User in Lock for which you want to
map with App user account, Click on edit icon shown on right side of the record, Select App user from
shown list and Click on “Save” to affect changes
User is not receiving “Remote Unlock” request on App or there is delay in
receiving it.
3
Make sure Lock is connected to Wifi Network, is Paired with Ozolife App and Internet is working.
For better experience make sure the Wifi signals are strong and signal strength is > - 60 dBm.
Unable to register fingerprint.
4
a) Check the fingers for dirt or wear. Also check the fingerprint sensor on the lock for dirt and oil stains, etc.
b) Check if the fingerprint sensor is working properly (Press any fingerprint on sensor to see if there is any
response.
Why is the smart lock consuming power faster than usual?
5
a) Large standby power consumption.
b) Short circuit.
After how many incorrect password attempts will the lock go in auto secure mode?
For how long it will be in auto secure mode?
6
Every time you enter a wrong password more than 5 times in a row, the keyboard is locked for 90 seconds.
FAQ
10            INTRODUCTION OPERATION F&Q APPENDIX

11

12

13
WARRANTY CARD
Invoice No.
Total Quantity
E-Mail ID

14

Ozone Secutech Pvt. Ltd. Registered Office: H 40, Bali Nagar, New Delhi - 110015, India
Operations Office: Plot No. 548, Phase V, Udyog Vihar , Gurugram, Haryana - 122016, India
Special Instructions:
• Please replace the battery as soon as the low voltage alarm signals it.
• Read this manual carefully before installation and keep it safe, for future reference.
OzoLife