Pacific energy Fusion User manual

081112-20 FUSION_D1 5055.5161
INSTALLATION
AND OPERATING
INSTRUCTIONS
SAFETY NOTICE: If this stove is not
properly installed, a house re may result.
For your safety, follow the installation
instructions. Contact local building or re
officials about restrictions and installation
inspection requirements in your area.
TESTED and LISTED to CAN/ULC S627
AND UL 1482
Meets the Environmental Protection
Agency's July 1990 Particulate Emission
Standards
IMPORTANT:
THESE INSTRUCTIONS ARE TO
REMAIN WITH THE HOMEOWNER
SAVE THESE INSTRUCTIONS
MODEL: FUSION
SERIES: D
PRODUCT CODES:
FSND.MBKC
FSND.SSC
SERIAL #

2 FUSION_D1 081112-20
PLEASE SAVE THESE INSTRUCTIONS
NOTE: WE STRONGLY RECOMMEND THAT SMOKE DETECTORS BE INSTALLED.
If smoke detectors have been previously installed, you may notice that they are operating more frequently. This may be due to
curing of stove paint or fumes caused by accidentally leaving the re door open. Do not disconnect the detectors. If necessary,
relocate them to reduce their sensitivity.
SAFETY NOTICE: If this stove is not properly installed, a house re may result. For your safety, follow the installation
instructions. Contact local building or re officials about restrictions and installation inspection requirements in you
area.
Please read this entire manual before you install and use your new room heater. Failure to follow instructions may result in property
damage, bodily injury, or even death.
Contents
Safety and Maintenance...................................................................................... 3
Maintenance Checks ........................................................................................... 4
Creosote ............................................................................................................... 5
Formation and Need for Removal.......................................................................................5
Chimney Fires.....................................................................................................................5
In Case of a Chimney Fire ..................................................................................................5
Avoiding a Chimney Fire..................................................................................................... 5
Stove Dimensions................................................................................................ 6
Minimum Clearance to Combustibles................................................................ 6
Mobile Home Installation .................................................................................... 7
Clearances .........................................................................................................................7
Procedure:...........................................................................................................................7
Listed Chimney and Chimney Connector ...........................................................................8
Residential Installation ....................................................................................... 9
Clearances .........................................................................................................................9
Chimney and Connector..................................................................................................... 9
Double-Wall Connector....................................................................................................... 9
Single-Wall Connector ........................................................................................................9
Procedure ...........................................................................................................................9
Floor Protector................................................................................................... 10
Combustion Air.................................................................................................. 10
Operation............................................................................................................ 11
Wood Selection................................................................................................................. 11
How to Test Your Wood ..................................................................................................... 11
Lighting for the First Time ................................................................................................. 11
Lighting a Fire................................................................................................................... 11
Normal Operation ............................................................................................................. 11
Restarting After Extended or Overnight Burns.................................................................. 12
More Wood, More Heat..................................................................................................... 12
Proper Draft ...................................................................................................................... 12
Ash Removal ....................................................................................................................12
Disposal of Ashes ............................................................................................................. 12
Baffle Removal ................................................................................................... 12
Removal............................................................................................................................ 12
Optional Blower ................................................................................................. 13
Blower Installation.............................................................................................................13
Blower Operation.............................................................................................................. 13
Appendix A......................................................................................................... 14
Troubleshooting ................................................................................................................14
Replacement Parts ........................................................................................................... 15
Label................................................................................................................................. 19

FUSION_D1 081112-20 3
Safety and
Maintenance
1. Burn wood only, dry and well seasoned. The denser or
heavier the wood when dry, the greater its heat value. This
is why hardwoods are generally preferred. Green or wet
wood should not be used, as it will reduce heat output, as
well as contributing signicantly to creosote buildup.
WARNING: Never use chemicals or any other
volatile liquid to start a re. Do not burn garbage, or
ammable uids such as gasoline, naptha, or engine
oil. We strongly recommend that smoke detectors be
installed.
2. Remove ashes frequently. Embers can roll out the door and
create a re hazard. Maintain a 1" minimum ash base.
3. If glass becomes darkened through slow burning or poor
wood, it can readily be cleaned with replace glass cleaner
when stove is cold. Never scrape with an object that might
scratch the glass. The type and amount of deposit on the
glass is a good indication of the ue pipe and chimney
buildup. A light brown dusty deposit that is easily wiped off
usually indicates good combustion and dry, well-seasoned
wood and therefore relatively clean pipes and chimney. On
the other hand, a black greasy deposit that is difficult to
remove is a result of wet and green wood and too slow a
burning rate. This heavy deposit is building up at least as
quickly in the chimney.
WARNING: ONLY USE MATERIALS SUPPLIED BY
MANUFACTURER WHEN DOING MAINTENANCE OR
REPLACEMENTS.
4. DOOR GASKETS - The gasket used by Pacic Energy
(7/8" medium density berglass rope) requires only light
pressure to seal. This will prolong seal life. It is important that
the door seal be maintained in good condition. Periodically
inspect seals and replace if necessary. Follow instructions
included in the DR31.WDGKIT kit obtainable from your
nearest Pacic Energy dealer.
5. DOOR GLASS - Do not slam loading door or otherwise
impact glass. When closing door, make sure that no logs
protrude to impact the glass. If the glass gets cracked or
broken, it must be replaced before using the stove.
Replacement glass can be obtained from your dealer. Use
8-13/16" x 15-1/4" x 5 mm. Ceramic glass only. Do not
substitute with any other type.
To remove broken glass, undo the four retaining screws and
remove clamps and frame, noting position for re-assembly.
Remove all particles of glass. Be careful as they are very sharp.
Install new glass complete with gasket. Replace frame, clamps
and screws.
CAUTION:
- do not overtighten, tighten screws very carefully
- do not clean glass when hot
- do not use abrasive cleaners on glass
6. The area where boost combustion air enters the rebox
must be kept clear of excessive ash buildup which will block
air ow. This area is at the front of the rebox.
7. Do not store wood within heater installation clearances, or
within the space required for fuel loading and ash removal.
Keep the area around the heater clean and free of loose
combustibles, furniture, newspapers, etc.
8. Establish a routine for the fuel, woodburning and ring
technique. Check daily for creosote buildup until experience
shows how often you need to clean to be safe.
9. Be aware that the hotter the re, the less creosote is
deposited. Weekly cleaning may be necessary in mild
weather, even though monthly cleaning is usually enough
in the coldest months when burning rates are higher.
10. Instruct all members of your family on the safe operation
of the heater. Ensure they have enough knowledge of the
entire system if they are expected to operate it. Stress the
section on chimney res and the importance of following
the steps outlined "In Case of Chimney Fire".

4 FUSION_D1 081112-20
Maintenance Checks
Check the following parts for damage such as cracks, excessive corrosion, burned out sections
and excessive warping: (See website for descriptions and more detail)
Weekly:
- Firebrick - Visual, for cracking.
- Door Gasket - sagging, placement, damage.
Monthly
- Brick rail tabs and brick rails.
- Air riser tube in the back of the rebox.
- Back side of airwash chamber.
- Baffle locking pin.
- Boost tube cover.
When Cleaning the
Chimney System:
- Top baffle board/blanket.
- Baffle.
- Top heat shield and mounting bolt.
- Baffle Gasket.
- Brick Rails.
- Manifold.
Blower:
- The blower should be cleaned out a minimum every six months by using a vacumn on the grill
openings in the back and bottom of the blower casing to remove any dust and debris.
- Some warping of the baffle is normal(up to 1/4” or .65cm).
- Replace if the baffle has permanent warping greater than this or has cracking or breakage.
- Please contact your Dealer if you experience any of the damage listed above. Continuing to
operate your stove with broken parts may accelerate damage to other parts and may void your
warranty

FUSION_D1 081112-20 5
Creosote
Formation and Need for Removal
When wood is burned slowly, it produces tar and other organic
vapours, which combine with expelled moisture to form creosote.
The creosote vapours condense in the relatively cool chimney
ue of a slow burning re. As a result, creosote residue accu-
mulates on the ue lining. When ignited, this creosote makes an
extremely hot re. The chimney connector and chimney should
be inspected periodically (at least once every two months)
during the heating season to determine if a creosote buildup
has occurred. If creosote has accumulated (3 mm. or more), it
should be removed to reduce the risk of a chimney re.
1. Highest smoke densities occur when a large amount of wood
is added to a bed of hot coals and the air inlet is closed.
The heated wood generates smoke, but without ample
air, the smoke cannot burn. Smoke-free, clean burning
requires small fuel loads, two or three logs at a time or 1/4
to 1/2 of fuel load and leaving the air inlet relatively wide
open, especially during the rst 10 to 30 minutes after each
loading, when most of the smoke generating reactions are
occurring. After 30 minutes or so, the air inlet can be turned
down substantially without excessive smoke generation.
Wood coals create very little creosote-producing smoke.
2. The cooler the surface over which the wood smoke is
passing, the more creosote will be condensed. Wet or green
wood contributes signicantly to creosote formation as the
excess moisture that is boiled off cools the re, making it
difficult for the tars and gases to ignite, thus creating dense
smoke and poor combustion. This moisture-laden smoke
cools the chimney, compounding the problem by offering
the smoke the ideal place to condense.
In summary, a certain amount of creosote is inevitable
and must be lived with. Regular inspection and cleaning is
the solution. The use of dry, seasoned wood and ample
combustion air will help to minimize the buildup.
Chimney Fires
The result of excessive creosote buildup is a chimney re.
Chimney res are dangerous. Chimney inside temperatures
can exceed 2000° F. This causes much higher than normal
temperatures in the chimney and on its exterior surfaces. Thus
ignition of nearby or touching combustible material is more
likely during a chimney re. Proper clearances are critical
during such a re.
Chimney res are easy to detect; they usually involve one or
more of the following:
-Flames and sparks shooting out of the top of the
chimney
-A roaring sound
-Vibration of the chimney
In Case of a Chimney Fire
1. Prepare to evacuate to ensure everyone's safety. Have a
well understood plan of action for evacuation. Have a place
outside where everyone is to meet.
2. Close air inlet on stove.
3. Call local re department. Have a re extinguisher handy.
Contact your local municipal or provincial re authority for
further information on how to handle a chimney re. It is
most important that you have a clearly understood plan on
how to handle a chimney re.
4. After the chimney re is out, the chimney must be cleaned
and checked for stress and cracks before starting another
re. Also check combustibles around the chimney and the
roof.
- The services of a competent or certied installer, (certied
by the Wood Energy Technical Training program (WETT) - in
Canada, Hearth Education Foundation (HEARTH) - in U.S.A.,)
are strongly recommended.
Avoiding a Chimney Fire
There are two ways to avoid chimney res:
1. Do not let creosote build up to a point where a big chimney
re is possible.
2. Do not have res in the heater that may ignite chimney
res. These are hot res, such as when burning household
trash, cardboard, Christmas tree limbs, or even ordinary
fuel wood (e.g.. with a full load on a hot bed of coals and
with the air inlet excessively open)

6 FUSION_D1 081112-20
DOUBLE WALL CONNECTOR - MOBILE HOME
DOUBLE WALL CONNECTOR - RESIDENTIAL
SINGLE WALL CONNECTOR - RESIDENTIAL
22 3/16”
13 1/2” 30 5/8”
19”
25 3/8”
25 3/8”
11 1/4”
11 1/4”
15 3/16” 6 1/2”
26 5/8”
15” 17”
11 1/2”
17”
20 3/16”
28 5/8”
4 1/4”
4 1/4” 18 3/8”
18 3/8”
8 1/4”
8 1/4”
22 3/8”
22 3/8”
17”
28 5/8”
18 3/16”
9 1/2”
23 1/4"
32 3/4"
36 1/2"
27 9/16"
23 3/4"
8 11/16"
Minimum
Clearance to
Combustibles
FIG. #1
Alcove: Min. Height 7 1/2'
Max. Depth 4'
Stove Dimensions
FIG. #2

FUSION_D1 081112-20 7
Procedure:
CAUTION: THE STRUCTURAL INTEGRITY OF THE MO-
BILE HOME FLOOR, WALL AND CEILING/ROOF MUST BE
MAINTAINED.
Note: See "Combustion Air" section on page 9.
1. Position stove and oor protection with hole for combustion
air in accordance with the clearances as stated on the label
and in Figure #2.
2. Mark the position for the hole in the ceiling and roof by
using a string and plumb-bob.
3. Check that the intended location will not interfere with oor
joists, ceiling joists or rafters before proceeding further.
4. Cut a hole in the ceiling and roof to suit the chimney system
and frame in the sides.The chimney support is mounted to
the framing.
5. Assemble chimney sections so the nished length is resting
on the support and protruding through the roof.Avoid having
joints between ceiling and roof. Install radiation shield.
Assemble ashing and storm collar and be sure to maintain
the vapour barrier at this point. (Seal securely.) Attach rain
cap and check ashing for leaks.
6. Install connector as per manufacturer's instructions.
7. Attach stove to ooring using two 1/4" x 2" or longer lag
screws.
Mobile Home
Installation
Warning: Under no circumstances is this heater to be installed
in a makeshift or "temporary" manner. It may be red only after
the following conditions have been met.
- DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE
SERVING ANOTHER APPLIANCE.
- DO NOT INSTALL IN A SLEEPING ROOM.
- Outside air supply must be used for Mobile Home installations
see Figure #3, Page 7.
- The services of a competent or certied installer, (certied
by the Wood Energy Technical Training program (WETT) - in
Canada, Hearth Education Foundation (HEARTH) - in U.S.A.)
are strongly recommended.
Clearances
This heater must be installed with listed double-wall connector
and compatible chimney system listed on page 7.
Clearances to combustible surfaces and materials are shown
in Figure #2, page 5 and Figure #3, page 7.
Clearances may be reduced with various heat insulating materi-
als. Consult local re codes and authorities for approval.
NOTE: Longer chimney lengths and different pitch ashings
may be used.All other parts listed must be installed (see Figure
#3, Page 7). Install all components to the connector or chimney
manufacturer's installation requirements.Consult your chimney
supplier for installation advice.

8 FUSION_D1 081112-20
FIG. #3 Chimney
Roof ashing
Storm collar
* 4" diameter air inlet with rodent screen
* If the crawl space is well ventilated it is not
necessary to extend air inlet to outside
Spark arres-
tor rain cap
Radiation shield
Chimney Connector
Chimney Support
50 1/2" (1283 mm)
Minimum
Minimum 7' (2.1m.)
Ceiling Height
Attachment to oor for
mobile homes inside base
Non-combustible
oor protector
48"
(1219 mm)
3' (914 mm)
Minimum
Hooded vent or
90 elbow turned down
The chimney may incorpo-
rate an offset. To do this
safely, all sections of listed
connector, offset elbows and
chimney section must be
screwed together by at least
three sheet metal screws
per joint. The chimney must
be suitably supported by
the chimney manufacturer's
listed offset support.
Listed Chimney and Chimney Connector
This appliance, when installed in a Mobile Home, must be installed with:
A. One of the following 6" double-wall connector systems:
1. Security Model DL or DC 5. Metal Fab Model DW
2. Oliver MacLeod Model PV 6. Ameri-Tec Model DBSP
3. Energy Vent 7. Industrial Chimney Model Excel Ultra-Black
4. Selkirk Metalbestos Model DS 8. Simpson Dura-Vent Model DVL
B. As well as one of the following compatible chimney systems - All parts 6":
CANADA ONLY: Security Pro-Jet ICC Selkirk Energy Vent
S2100 H.T.3000 Excel 2100 Sentinal CF Commander 5000
Ceiling support XSF FCS SF CF-CSP CH6LCS
Rafter radiation shield RRS
3' Chimney length XL3 SL3 L3 CF-36SL CH636
2' Chimney length XL2 SL2 L2 CF-24 CH624
Roof ashing XFA RF17 FA CF-FRA CH6TCF
Storm collar XSC SC SC CF-SC CH6SC
Spark arrestor rain cap XCPE RCSA CPE CF-SA,CT CH6RC, SS
USA ONLY: Security Pro-Jet Security Pro-Jet Metalbestos MetalFab Ameritech ICC Simpson Dura-Vent
S2100 H.T.3000 ASHT HT3103 SSII 2100 TEC HS Excel 103HT Dura/Plus Dura Tech
Ceiling support XSF FCS SF FCS T-SFA TGCSP 6PL-CS RDS/SQS SDP-SB SDP-SB
Rafter radiation shield RRS RRS T-JSMH TGRS
3' Chimney length XL3 SL3 L3 SL3 T-36 TG3 HS 36 CL48 SDP-P SDT-P
2' Chimney length XL2 SL2 L2 SL2 T-24 TG2 HS 24 CL24 SDP-P SDT-P
Roof ashing XFA RF17 FA RF T-SFA TGF 8RFFU VF SDP-F SDT-F
Storm collar XSC SC SC SC T-SC TGSC PL-ASCG SC SDP-SC SDT-SC
Spark arrestor rain cap XCPE RCSA CPE RCSA T-CT TGC 6PL-MPC RCS SDP-C SDT-C

FUSION_D1 081112-20 9
Residential
Installation
Warning: Under no circumstances is this heater to be installed
in a makeshift or "temporary" manner. It may be red only after
the following conditions have been met.
* DO NOT ATTEMPT TO CONNECT THIS HEATER TO ANY
AIR DISTRIBUTION DUCT.
* The services of a competent installer are strongly
recommended.
* Outside combustion air or fresh air into the room may be
required in your area, consult local building codes (see
Combustion Air section).
- The services of a competent or certied installer, (certied
by the Wood Energy Technical Training program (WETT) - in
Canada, Hearth Education Foundation (HEARTH) - in U.S.A.)
are strongly recommended.
Clearances
1. This heater may be installed using a single-wall connector
(smoke pipe) or listed double-wall connector (see Mobile
Home installation).
2. Clearances to combustible surfaces and materials using
single-wall connector are shown in Figure #2, page 5.
Clearances may be reduced with various heat insulating
materials. Consult local re codes and authorities for
approval.
3. Alternately, for close clearances, use a listed double-wall
connector. See Figure #2, page 5.
Chimney and Connector
Connect to a listed chimney or a chimney suitable for use with
solid fuel that is lined and in good condition and meets local
building codes. The chimney ue size should be the same as
the stove outlet for optimal performance.Reducing or increasing
the ue size may adversely affect stove performance. Chimney
ue exit is to be 3 feet (1 m.) above roof and two feet (0.6 m.)
above highest projection within 10 feet (3 m.). The installation
must meet all local codes.Do not connect this unit to a chimney
ue serving another appliance.
Double-Wall Connector
- Use a listed double-wall connector.
- Install all components to the chimney connector
manufacturer's installation requirements.
Single-Wall Connector
Smoke pipe must be:
* as short and straight as possible, use six inch diameter, 24
gauge black pipe that is clean and in new condition.
* secured at every joint and collar with 3 sheet metal
screws.
* installed with the crimped or male ends pointing down. This
will carry any liquid creosote or condensation back into the
stove.
* The chimney connector shall not pass through an attic, roof
space, closet or similar concealed space, oor, or ceiling.
Where passage through a wall, or partition of combustible
material is desired, the installation shall conform to CAN/
CSA-B365, Installation Code for Solid-Fuel-Burning
Appliances and Equipment.
Procedure
1. If a listed chimney and double-wall connector is to be
connected to the stove, install all components to the
chimney manufacturer's installation requirements. (Outside
combustion air may be required, consult local building
codes. See Combustion Air section.)
2. If it is desirable to use smoke pipe in conjunction with the
insulated chimney, see step 4.
3. If a roof or ceiling support is used in the installation, you
will nd the chimney manufacturer's complete instructions
packed with the roof support.
4. To start installing smoke pipe (chimney connector), slip
crimped edge of the pipe inside the stove collar. Use holes
provided in collar to secure pipe with two screws.
5. Install the remaining lengths of pipe one on top of the other
to the nished height of the chimney connector and secure
to each other.

10 FUSION_D1 081112-20
Canada Only
Floor Protector
The stove may be installed on a combustible oor provided
noncombustible ember protection is used.
This protection must extend as follows:
In Canada: 18" (457 mm) on the ring side and 8" (203 mm)
to the other sides. See Figure #4, below.
Combustion Air
Intake or combustion air can be supplied to the stove in one of
two ways. Consult your local building code or CAN/CSA-B365,
Installation Code for Solid-Fuel-Burning Appliances and Equip-
ment before proceeding.
1. Outside air supply - (Necessary for mobile home
installation, optional for residential installation.) Outside
air may be drawn from either underneath the stove or from
behind.
To draw outside air through the oor, leave the 4" knockout
or cover plate in place in the rear of the stove.
Cut or drill a 4" diameter hole in the oor anywhere inside
the perimeter of the pedestal. Cover the hole with a 4" x
4" (100 mm x 100 mm) rodent screen and staple/nail in
place.
This hole must get its air from a ventilated crawl space
or be extended with duct to the outdoors (see Figure #3,
Page 7). The use of outside combustion air for residential
installation requires the unit to be secured to the structure
to prevent dislodging of the air duct. Outside air may also
be ducted from outside through the 4" diameter hole in
the rear of the pedestal enclosure if you remove the cover
plate(Fig #6).
Note: This unit is not designed to be operated with the ring
door open. In addition to the obvious hazard of sparks
landing on combustibles, an open re door will cause the
heater to draw air from the living space and possibly cause
suffocation.
2. Room air supply - Remove the 4" cover from the rear of
the pedestal enclosure. The stove will now draw its air
from the room through this opening and into the rebox
intake(Fig.#6).
Note: The living space around the heater must be well
ventilated with good air circulation. Anything that may cause
a negative pressure can cause gases or fumes to be pulled
into the living area. During extremely cold weather, and
especially when burning at very slow rates, the upper parts
of the exposed chimney may ice up, partially blocking the
ue gases. If blockage occurs, ue gases may enter living
space.
U.S.A. Only
Non-combustible
oor protector
FIG. #4
FIG. #5
In USA: 16" (406 mm) to the front and 8" (203 mm) to the sides
of the fuel loading door opening. See Figure #5, below. This
protection is also required under the chimney connector and
2" (51 mm) beyond each side.
Minimum Width - 39 1/4"
Minimum Overall Depth - 51 5/16"
Non-combustible
oor protector
Minimum Width - 35"
Minimum Overall Depth - 41 5/16"
8" [203mm]
18" [457mm]
8" [203mm]
8" [203mm]
8" [203mm]
16" [406mm]
8" [203mm]
FIG. #6

FUSION_D1 081112-20 11
Operation
CAUTION: Never use gasoline, gasoline type lantern fuel, kero-
sene, charcoal lighter uid or similar liquids to start or "freshen
up" a re in this heater. Keep all such liquids well away from
the heater while it is in use.
CAUTION: Hot while in operation. Keep children, clothing
and furniture away. Contact may cause skin burns.
Your PACIFIC ENERGY heater is designed for maximum overall
efficiency at a moderate ring rate. Overring is hazardous and
a waste of fuel. Too slow a burn contributes to creosote buildup
and lowers combustion efficiency.
Wood Selection
This heater is designed to burn natural wood only. Higher ef-
ciency and lower emissions generally result when burning
air-dried seasoned hardwoods, as compared to softwoods or
too green or freshly cut hardwoods.
Wood should be properly air dried (seasoned) for six months or
more. Wet or undried wood will cause the re to smoulder and
produce large amounts of creosote. Wet wood also produces
very little heat and tends to go out often.
DO NOT BURN :
-Salt water wood * -Treated wood
-Wet or green wood -Coal/charcoal
-Garbage/Plastic * -Solvents
* These materials contain chlorides which will rapidly
destroy metal surfaces and void warranty.
Do not burn anything but wood. Other fuels, eg. charcoal,
can produce large amounts of carbon monoxide, a tasteless,
odourless gas that can kill. Under no circumstances should
you attempt to barbecue in this heater.
How to Test Your Wood
Add a large piece of wood to the stove when it has a good large
bed of coals. It is dry if it is burning on more than one side
within one minute. It is damp if it turns black and lights within
three minutes. If it sizzles, hisses and blackens without igniting
in ve minutes it is soaked and should not be burnt.
Lighting for the First Time
Curing of the Paint Finish
To achieve the best nish, the paint on your stove must be baked
on. When burning your stove for the rst 2-3 times it is very
important that the room be well ventilated. Open all windows
and doors. Smoke and fumes caused by the curing process
may cause discomfort to some individuals.
Lighting a Fire
WARNING: Never use chemicals or any other volatile liquid
to start a re.
1. Move air control lever to the left-most position (maximum
ring rate) and open door.
2. Place crumpled newspaper in the centre of the heater and
criss-cross with several pieces of dry kindling. Add a few
small pieces of dry wood on top.
3. Ignite the paper and close the door.
4. After the re has established itself, open the door and add
a few small logs. Close door.
5. Begin normal operation after a good coal base exists and
wood has charred.
Normal Operation
1. Set air control to a desired setting. If smoke pours down
across the glass (waterfall effect) this indicates you have
shut the control down too soon or you are using too low a
setting. The wide range control panel makes nding the
desired setting for your application easy. As every home's
heating needs vary (ie. insulation, windows, climate, etc.)
the proper setting can only be found by trial and error and
should be noted for future burns.
2. To refuel, adjust air control to high, and give the re
time to brighten. Open the door slowly, this will prevent
backpuffing.
3. Use wood of different shape, diameter and length (up to 18").
Load your wood endwise and try to place the logs so that
the air can ow between them. Always use dry wood.
4. Do not load fuel to a height or in such a manner that would
be hazardous when opening the door.
5. For extended or overnight burns, unsplit logs are preferred.
Remember to char the wood completely on maximum setting
before adjusting air control for overnight burn.
WARNING:Always keep loading door closed when burning.
This heater is not designed for open door burning.
WARNING: No alteration or modication of the combustion
air control assembly is permitted. Any tampering will void
warranty and could be very hazardous.
WARNING: Do not use grates or andirons to elevate the
fuel. Burn directly on the re bricks. Replace broken or
missing bricks. Failure to do so may create a hazardous
condition.

12 FUSION_D1 081112-20
Ash Removal
Caution: Ashes are to be removed only when the heater is
cold.
Whenever ashes get 3 to 4 inches deep in your rebox, and
when re has burned down and cooled, remove excess ashes.
Leave an ash bed approximately 1" (25 mm) deep on the rebox
bottom to help maintain a hot charcoal bed.
Ash Cleanout system: The ash dump handle is located under
the ash lip on the left hand side. To operate ash dump, pull
handle out 1/2" and turn clockwise. This will unlock the ash
dump and allow it to open. Hold handle open while pulling ashes
into the opening. Avoid large embers as these still contain heat
value. Release handle and push in to lock. Ensure ash dump
door is properly engaged. Fill the cavity with the remaining ash
level with the rebox oor. Lift and pull out ashpan and discard
ashes into metal container. Replace ashpan and ensure it is
seated properly.
Do not burn with ash dump door open. Doing so will cre-
ate a hazardous condition. Always leave about 1" of ash
when cleaning.
Disposal of Ashes
Ashes should be placed in a metal container with a tight tting
lid. The closed container of ashes should be placed outside
on a non-combustible oor or on the ground, well away from
all combustible materials, pending nal disposal. If the ashes
are disposed of by burial in soil or otherwise locally dispersed,
they should be retained in closed container until all cinders
have thoroughly cooled. Other waste should not be placed in
this container.
Baffle Removal
Chimney connector pipe should be disconnected from stove
to clean and inspect. Only if this is not possible should you
remove baffle assembly.
DO NOT OPERATE WITH BAFFLE ASSEMBLY OR
INSULATION REMOVED.
Removal
Remove retaining pin at the back top of the rebox, just under
the baffle. Lift baffle up and pull forward to disconnect from
the supply tube. Tilt baffle sideways to drop down and remove
from rebox. Inspect gasket between baffle and supply tube.
If necessary, replace with gasket #139.5 available from your
Pacic Energy dealer. Re-install baffle assembly in reverse
order. The two side pieces of insulation must be tight against
the side rails.
Restarting After Extended or
Overnight Burns
1. Open door and rake hot embers towards the front of the
heater. Add a couple of dry, split logs on top of embers,
close door.
2. Adjust air control to high (control lever to the left) and in just
a few minutes, logs should begin burning.
3. After wood has charred, reset air control to desired
setting.
4. To achieve maximum ring rate, set air control lever to the
left-most position. Do not use this setting other than for
starting or preheating fresh fuel loads.
DO NOT OVERFIRE THIS HEATER: Attempts to achieve heat
output rates that exceed heater design specications can
result in permanent damage to the heater and chimney.
More Wood, More Heat
Seasoned wood has approximately 7500 BTU's per pound. If
you put 10 pounds of wood in your stove for an eight hour burn
the wood will be producing 9375 BTU's per hour. (7500 BTU x
10 lbs./8hrs.=9375 BTU's per hr.) If you put 20 lbs of wood in
your stove for eight hour burn you will get 18,750 BTU's per hr.
(7500 BTU x 20lbs./8hr.=18,750 BTU's per hr.). This is only an
example and is based on 100% efficiency. In reality, your stove
should perform above the 80% range.
Experience will give you the right settings for proper combustion
and efficient burning. Remember, the correct air inlet setting is
affected by variables such as type of wood, outside temperature,
chimney size and weather conditions. With practice, you will
become procient in operating your heater and will obtain the
performance for which it was designed.
Proper Draft
1. Draft is the force which moves air from the appliance up
through the chimney. The amount of draft in your chimney
depends on the length of the chimney, local geography,
nearby obstructions and other factors.
2. Too much draft may cause excessive temperatures in the
appliance. An uncontrollable burn or a glowing red stove
part or chimney indicates excessive draft.
3. Inadequate draft may cause backpuffing into the room
and plugging of the chimney. Smoke leaking into the room
through appliance and chimney connector joints indicates
inadequate draft.

FUSION_D1 081112-20 13
Optional Blower
The optional blower kit (kit #WODC.BLOW) is equipped with a
three prong power cord and may be installed at any time. Fol-
low installation instructions supplied with the kit. Route power
supply cord away from heater.
Electrical rating: 115 volts A.C.-1.02 amps.
Fan output rating: 125 CFM
Blower Installation
1. Loosen the 2 screws at the center of the blower.
2. Install the temperature snap-switch assembly onto the
blower by placing the bracket over the screws.Fig. #7
3. Tighten the screws.
4. Ensure that the two wires are connected to the temperature
snap-switch.
5. Bend over the blower clearance tab and shown in Fig. #8.
6. Feed the power cord into the pedestal base and out through
the round hole near the bottom.
7. Slide the temperature snap-switch assembly up into the
space between the rear shield and the rebox, ensuring
that the temperature snap-switch contacts the rebox. Fig.
#8
8. Install the two screws through the ange of the blower into
the rear shield. Fig. #9
9. Plug the power supply cord in and check blower
operation. Power Cord
Clearance
Ta b
Temperature
Switch
Blower Operation
Proper blower speed matched with air control setting will ensure
peak performance from your stove. Operate as follows:
- Air control set to low (right-most position), operate blower
speed control on "Low".
-Air control set between low and high, operate blower speed
control at desired setting.
Automatic: To operate the blower automatically, set the rocker
switch on the side of the fan housing to "Auto" and set the speed
control to desired setting. This will allow the fan to turn on as
the stove heats up to operating temperature. It will also shut
the blower off after the re has gone out and the unit cooled to
below a useful heat output range.
Manual: To manually operate the blower, set the rocker switch
to "Man" and set the speed control to desired setting.This will by-
pass the sensing device and allow full control of the blower.
Switching from "Auto" to "Man" or selecting speed may be
done anytime.
FIG. #7
FIG. #8
FIG. #9

14 FUSION_D1 081112-20
Appendix A
Troubleshooting
Problem Cause Cure
Glass is Dirty 1. Wood is wet - Use dry wood
2.Turning down air control - Do not turn down until
or damper too soon a) there is a good bed of coals
b) the wood is charred
3.Draft too low - Improper chimney height and / or diameter
- Chimney plugged or restricted, inspect and
clean
- Provide outside air for combustion
4. Door gasket leakage - Replace gasket
- Check latch
Excessive Creosote Buildup - See 1,2,3, above.
Low Heat Output 1. Wood is wet - Use dry wood
2.Fire too small - Build a larger re
3.Draft too low - Chimney plugged or restricted, inspect and
clean
Won't Burn Overnight 1. Air control is set too high - Set control lower
2. Not enough wood - Unsplit wood is preferred for overnight burns
3. Draft too high - Excessive chimney height and/or diameter
Stove Won't Burn 1. Combustion air supply blocked - Check outside air supply for obstruction
- Check that room air cover is removed
2.Draft too low - Chimney plugged or restricted, inspect and
clean
- Chimney oversized or otherwise unsuitable,
consult Dealer

FUSION_D1 081112-20 15
ITEM/ ARTICLE DIMENSIONS PART NUMBER/ NUMÉRO DE PIÈCE
A 1 1/2” X 4 1/2” X 1 1/4” (39 mm x 115 mm x 32 mm) 248.0
B 3” X 4 1/2” X 1 1/4” (77 mm x 115 mm x 32 mm) 247.0
C 4” X 4 1/2” X 1 1/4” (102 mm x 115 mm x 32 mm) 246.0
D 7 1/4” X 4 1/2” X 1 1/4” (184 mm x 115 mm x 32 mm) 245.0
E 9” X 4 1/2” X 1 1/4” (230 mm x 115 mm x 32 mm) 5096.99
Super 27, Spectrum, Spectrum Classic, and Fusion
Firebrick Installation Instructions/
Instructions d’Installation de
Briques Réfractaires
This package contains 18 full-size firebricks, as well as
3 various cut-size bricks.
If your heater came with an ash cleanout system, or
an optional one is being installed, discard the extra full
brick.
With the heater in the upright position, install firebricks
as follows:
- Place firebricks on the bottom of the heater first. Total
of 6 full-size then either “A, B & C” as shown below, if
you are installing the optional ash cleanout system or
1 full brick in place of “A & B” if you are not installing
the ash cleanout system.
- Next, install the side firebricks, 4 full-size each side.
- Lastly, install 3 full-size firebricks against the rear
wall.
Cet emballage contient 17 briques réfractaires, à
pleine grandeur, ainsi que 4 briques coupées de diffé-
rentes grandeurs. Si votre poêle a déjà un système de
vidange des cendres ou l’un de ceux-ci est installé en
option, n’utilisez pas la brique “B”.
Avec le poêle en position debout, installez les briques
comme suit:
- Briques réfractaires d’endroit sur le fond de l’appareil
de chauffage d’abord. Le Total de 6 pleine grandeur
alors «A, B et C» comme indiqué ci-dessous, si vous
installez la cendre facultative cleanout le système ou
1 brique pleine en place «d’A et B» si vous n’installez
pas la cendre cleanout le système.
- Ensuite, installez les briques de coté, 4 briques
pleines de chaque coté.
- Finalement, installez 3 briques pleines contre le mur
arrière.
ABC
D

16 FUSION_D1 081112-20
Replacement Parts
(WHEN ORDERING, INCLUDE PART NUMBER WITH DESCRIPTION)
ITEM DESCRIPTION PART NO. ITEM DESCRIPTION PART NO.
1a..........Side Shield, Left, Black ......................... FSND.4640
..............Stainless Steel .................................................4657
1b..........Side Shield, Right, Black....................... FSND.4639
..............Stainless Steel .................................................4656
2............Top Air Deector, Black .............FSND.46032MBKA
..............Stainless Steel ............................. FSND.46031SSA
3............Door Catch ............................................ FSND.4646
4............Glass Clamps (4 pc.)............................ DRFS.4649
5............Replacement Glass (c/w Tape) ....... DR31.WGLKIT
6............Door Gasket Kit................................DR31.WDGKIT
7............Door Frame ................................... DRFS.4642WLD
8............Door Frame Overlay, Black....................DRFS.4641
..............Stainless Steel .................................................4654
9............Door Handle Assembly.......................... DRFS.4638
10.......... Boost Manifold ................................................. 4105
11.......... Firebrick Set ....................................... BRIC.SSERA
All parts may be ordered from your nearest Pacic Energy
dealer. Contact Pacic Energy for the location of the dealer
12a........Brick Rail Set.................................. SSER.RAILSET
13..........Replacement Baffle Kit..................... SSER.DBAKIT
13a........Baffle (not sold separately).................. SSER.DBAF
13b........Side Insulation (not sold separately) ..... 5068.732.B
13c........Baffle Pin ........................................... SSER.125001
13d........Baffle Gasket......................................... SSER.1395
14..........Flame Shield (c/w Bolt and Nut)........... WINS.4531
15..........Air Shutter Assembly ............................. FSND.4631
16..........Baffle Air Control Assembly ..................... SSER.214
17..........Ash Dump Assembly ............................WODC.2261
18..........Ash Box................................................. FSND.4615
17
13b
13a
13b
13c
13d
1b
1a
2
3
13
10
7
8
65
4
9
11
18
12
14
15
16
FIG. #10

FUSION_D1 081112-20 17

18 FUSION_D1 081112-20

FUSION_D1 081112-20 19
Label
A.
19 in. / 483 mm 15 in. / 381 mm
B.
13.5 in. / 343 mm <9.5 in. / 241 mm
C.
11.3 in. / 287 mm 11.3 in. / 287 mm
D.
27.5 in. / 699 mm 23.5 in. / 598 mm
E.
19.1 in. /485 mm <15.1 in /384 mm
F.
22.2 in. / 564 mm 22.2 in. / 564 mm
A.
15 in. / 381 mm 15 in. / 381 mm
B.
6.5 in. / 165 mm 6.5 in. / 165 mm
C.
4.3 in. / 109 mm 4.3 in. / 109 mm
D.
23.5 in. / 598 mm 23.5 in. / 598 mm
E.
12.1 in. / 307 mm 12.1 in. / 307 mm
F.
15.2 in. / 386 mm 15.2 in. / 386 mm
A.
17 in. / 432 mm 17 in./432 mm
B.
11.5 in. / 292 mm 9.5 in./241 mm
C.
N/A 8.3 in. / 211 mm
D.
25.5 in. / 648 mm 25.5 in./648 mm
E.
17.1 in. / 434 mm 15.1 in /384 mm
F.
N/A 19.2 in. / 488 mm
CERTIFIED FOR CANADA AND U.S.A. - SERIES / SÉRIE: DMODEL / MODÈLE: FUSION LISTED ROOM HEATER, SOLID FUEL TYPE. ALSO FOR USE IN MOBILE HOMES TESTED TO/ ÉPROUVÉ SELON: CAN/ULC S627-M93 AND UL 1482-98
• INSTALL AND USE IN ACCORDANCE WITH THE MANUFACTURER’S INSTALLATION AND OPERATING INSTRUCTIONS. • CONTACT LOCAL BUILDING OR FIRE OFFICIALS ABOUT RESTRICTIONS, INSTALLATION PERMIT AND INSPECTION IN YOUR AREA. • DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE (USA. ONLY). • USE 6 INCH / 150MM DIAMETER MINIMUM 24 MSG BLACK OR LISTED CONNECTOR. • CAN BE CONNECTED TO A LINED MASONRY CHIMNEY SUITABLE FOR USE WITH SOLID FUELS. • DO NOT OBSTRUCT THE SPACE BENEATH THE HEATER. • SEE LOCAL BUILDING CODE AND MANUFACTURER'S INSTRUCTIONS FOR PRECAUTIONS REQUIRED
WHEN PASSING A CHIMNEY THROUGH A COMBUSTIBLE WALL OR CEILING.
• DO NOT PASS A CHIMNEY CONNECTOR THROUGH A COMBUSTIBLE WALL OR CEILING. • MINIMUM CLEARANCE BETWEEN SINGLE WALL CHIMNEY CONNECTOR AND COMBUSTIBLE MATERI-
ALS-18INCHES/455MM. CLEARANCE MAY BE REDUCED BY THE USE OF LISTED PIPE SHIELDS, WALL PROTECTORS OR OTHER MEANS APPROVED BY LOCAL BUILDING OR FIRE OFFICIALS.
• COMPONENTS REQUIRED FOR MOBILE HOME AND ALCOVE INSTALLATION: OUTSIDE AIR KIT. BOTH CHIMNEY SYSTEM AND CONNECTOR MUST BE LISTED TO:
IN CANADA - ULC S-641 LISTED CONNECTOR AND ULC-S-629 LISTED CHIMNEY
IN CANADA - ULC S-641 LISTED CONNECTOR AND ULC-S-629 LISTED CHIMNEY
IN USA - UL-103 HT LISTED CONNECTOR AND CHIMNEY
IN USA - UL-103 HT LISTED CONNECTOR AND CHIMNEY • USE COMPONENTS SPECIFIED IN PACIFIC ENERGY INSTALLATION INSTRUCTIONS. • APPLIANCE MUST BE INSTALLED WITH PEDESTAL OR LEG KIT ATTACHED. • OPTIONAL COMPONENTS - FAN KIT, FAN ELECTRICAL RATING: 115V, 60HZ, 1.0 AMP. DO NOT ROUTE POWER CORD BENEATH HEATER. • CAUTION: RISK OF EXCESSIVE TEMPERATURES - KEEP ASH DUMP CLOSED DURING FIRING OF THE
HEATER.
• OPERATE ONLY WITH FEED DOOR CLOSED. OPEN TO FEED FIRE ONLY. • KEEP FURNISHINGS AND OTHER COMBUSTIBLE MATERIALS WELL AWAY FROM HEATER. • REPLACE GLASS ONLY WITH CERAMIC GLASS. HORIZONTAL CONNECTOR NOT PERMITTED IN MOBILE HOMES  AS TESTED - PIPE SHIELD MAY BE REQUIRED BY LOCAL AUTHORITIES. * COMBUSTIBLE ALCOVE SIZE : DEPTH - 3 FT. / .91 M MAX., HEIGHT 7 FT. / 2.1 M MIN., WIDTH 4 FT. / 1.2 M
MIN.
COMBUSTIBLE FLOOR MUST BE PROTECTED BY A CONTINUOUS NON-COMBUSTIBLE MATERIAL EX-
TENDED TO THE FRONT, SIDES AND BACK AS INDICATED.
MINIMUM CLEARANCES TO
COMBUSTIBLE MATERIALS/
DÉGAGEMENTS MINIMALES AUX
MATÉRIAUX COMBUSTIBLES
DO NOT REMOVE THIS LABEL
RACCORD
VERTICAL CONNECTOR
RACCORD
HORIZONTAL CONNECTOR
RESIDENTIAL CLOSE CLEARANCE INSTALLATION
USING DOUBLE WALL CONNECTOR/
INSTALLATION
RÉSIDENTIELLE AVEC DÉGAGEMENT MINIMAL, UTILISANT
UN RACCORD DE MUR DOUBLE
* ALCOVE INSTALLATION
USING DOUBLE WALL
CONNECTOR/
* INSTALLATION
EN ALCÔVE UTILISANT UN
RACCORD DE MUR DOUBLE
WH-
RESIDENTIAL INSTALLATION
USING SINGLE WALL CONNECTOR/
INSTALLATION RÉSIDENTIELLE UTILISANT UN
RACCORD DE MUR SIMPLE
IN CANADA G. 18 INCHES / 455 MM AU CANADA
H. 8 INCHES / 200 MM
I. 8 INCHES / 200 MM IN U.S.A. G. 16 INCHES / 405 MM
AUX ÉTATS-UNIS
H. 5 INCHES / 127 MM
I. 0 INCHES / 0 MM
MOBILE
HOME INSTALLATION
USING DOUBLE WALL
CONNECTOR/
INSTALLATION
EN MAISON MOBILE UTILISANT
UN RACCORD DE MUR DOUBLE
WN#16830 ETL#4001507
• INSTALLEZ ET UTILISEZ SELON LES INSTRUCTIONS D’INSTALLATION ET D’OPÉRATION FOURNI AVEC L’APPAREIL.. • CONTACTEZ LES OFFICIELS DE LA CONSTRUCTION OU DE SERVICE D’INCENDIE POUR DES INFORMATIONS QUANT AUX
RESTRICTIONS. PERMIS D’INSTALLATION ET INSPECTIONS DANS VOTRE RÉGION.
• NE RELIEZ PAS CET APPAREIL À UN CONDUIT DE CHEMINÉE DESSERVANT DÉJÀ UN AUTRE APPAREIL (ÉTATS-UNIS SEULE-
MENT).
• UTILISEZ UN RACCORDEMENT NOIR OU CLASSÉ DE 24 MSG ET AVEC UN DIAMÈTRE D’AU MOINS 6 POUCES / 150 mm. • PEUT ÊTRE CONNECTÉ À UNE CHEMINÉE DE MAÇONNERIE ALIGNÉE PRÊTE À L’EMPLOI AVEC DES COMBUSTIBLES SOLIDES. • DO NOT OBSTRUCT THE SPACE BENEATH THE HEATER / • CONSULTEZ LE CODE LOCAL DE CONSTRUCTION ET LES INSTRUCTIONS DU FABRICANT QUANT AUX PRÉCAUTIONS À
PRENDRE LORSQUE VOUS FAITES PASSER UNE CHEMINÉE À TRAVERS D’UN MUR OU D’UN PLAFOND COMPOSÉS DE MATÉ- RIAUX COMBUSTIBLES.
• NE FAITES PAS PASSER UN RACCORDEMENT DE CHEMINÉE À TRAVERS D’UN MUR OU D’UN PLAFOND COMPOSÉS DE MATÉ-
RIAUX
• DÉGAGEMENT MINIMAL ENTRE UN RACCORDEMENT DE CHEMINÉE À UN MUR SIMPLE ET TOUT MATÉRIEL COMBUSTIBLE - 18
POUCES / 455 mm. CE DÉGAGEMENT PEUT ÊTRE RÉDUIT EN UTILISANT DES PROTECTEURS DE TUYAUX CLASSÉS, PROTEC- TEURS DE MUR OU AUTRES MOYENS APPROUVÉS PAR LES OFFICIELS DE LA CONSTRUCTION OU DU SERVICE D’INCENDIE DE VOTRE RÉGION.
CONNECTEUR HORIZONTAL NON PERMIS DANS MAISONS MOBILES • L’APPARIEL DOIT COMPORTER UN ENSEMBLE POUR PIEDSTABLE OU SUR PATTES. • PIÈCES REQUISES POUR INSTALLATION EN MAISON MOBILE OU EN ALCÔVE: NÉCESSAIRE D’APPROVI-
SIONNEMENT D’AIR EXTÉRIEUR ET L’UN DES RACCORDS SUIVANTS: EN COMBINAISON AVEC L’UN DES SYSTÈMES DE CHEMINÉE COMPATIBLES SUIVANTS:
AU CANADA - LE ULC S-641 CONNECTEUR ENUMERES ET ULC-S-629 ONT ENUMERE CHEMINEE • PIÈCES EN OPTION - NÉCESSAIRES DE SOUFFLERIE, INDICES ÉLECTRIQUES DE SOUFFLERIE: 115V, 60HZ, 1.0 AMP. LE FIL
ÉLECTRIQUE NE DOIT PAS ÊTRE PLACÉ SOUS LE POÈTE.
LE FIL ÉLECTRIQUE NE DOIT PAS ÊTRE PLACÉ SOUS LE POÊLE • ATTENTION: RISQUE DE TEMPÉRATURES EXCESSIVES - GARDES LE TIROIR DE CENDRES FERMÉ PENDANT L’ALLUMAGE DU
POÈTE.
• OPÉREZ SEULEMENT LORSQUE LA PORTE D’ALIMENTATION EST FERMÉE. • OUVREZ SEULEMENT POUR ALIMENTER LE FEU. • GARDEZ LES MEUBLES ET AUTRES MATÉRIAUX COMBUSTIBLES BIEN ÉLOIGNÉS DU POÊLE. • REMPLACES LA VITRE AVEC UNIQUEMENT DE LA VITRE CÉRAMIQUE. CONNECTEUR HORIZONTAL NON PERMIS DANS MAISONS MOBILES TEL QUO ÉPROUVÉ UN PROTECTEUR DE TUYAU PEUT ÊTRE REQUIS PAR LES AUTORITÉS LOCALES * DIMENSION D’ALCOVE COMBUSTIBLE: PROFONDEUR - 3 PIEDS / .91M, HAUTEUR 7 PIEDS/2.1M, LARGEUR 4 PIEDS/1.2M MINI-
MUM.
LE PLANCHER COMBUSTIBLE DOIT ÊTRE PROTÉGÉ PAR UN MATÉRIEL NON-COMBUSTIBLE TOUT D’UNE PIÈCE QUI DOIT
S’ÉTENDRE DE PAR LE DEVANT, LES COTÉS ET L’ARRIÈRE TEL QU’INDIQUÉ.
A. SIDEWALL TO UNIT/
MUR DE CÔTE / APPAREIL
B. BACKWALL TO UNIT/ M
UR DE FOND / APPAREIL
C. CORNER TO UNIT/ COIN / APPAREIL D. SIDEWALL TO CONNECTOR/ MUR DE CÔTE / RACCORD E. BACKWALL TO CONNECTOR/ MUR DE FOND / RACCORD F. CORNER TO CONNECTOR/ COIN / RACCORD
BACK I
HEATER
G
SIDE
H
FRONT
SIDE
H
COTE
COTE
DEVANT
POELE
DOS
RACCORD
VERTICAL CONNECTOR
RACCORD
HORIZONTAL CONNECTOR
MADE IN CANADA/
FABRIQUÉ AU CANADA
J F M A M J J A S O N D
2012 2013 2014 2015 2016 2017
DATE OF MANUFACTURE/
DATE DE MANUFACTURE
FSND-1
U.S. ENVIRONMENTAL PROTECTION AGENCY CERTIFIED TO COMPLY WITH JULY, 1990, PARTICULATE EMISSION STANDARDS//
CERTIFIÉ PAR L’AGENCE DE PROTECTION DE
L’ENVIRONNEMENT DES ÉTATS-UNIS (EPA) EN ACCORD AVEC LES STANDARDS D’ÉMISSION DE PARTICULES DE JUILLET 1990
5050.7624081112
MANUFACTURED BY/
FABRIQUÉ PAR:
PACIFIC ENERGY FIREPLACE PRODUCTS LTD.
2975 ALLENBY RD., DUNCAN, BC V9L 6V8
HOT WHILE IN OPERATION. DO NOT TOUCH. KEEP CHILDREN, CLOTHING AND FURNITURE AWAY. CONTACT MAY CAUSE SKIN BURNS. SEE NAMEPLATE AND INSTRUCTIONS.//
CHAUD LORSQU’EN OPÉRATION. NE PAS TOUCHER, TENEZ LES
ENFANTS ET LES VÊTEMENTS BIEN À L’ÉCART. LE CONTACT PEUT CAUSER DES BRÛLURES À LA PEAU. CONSULTEZ LA PLAQUE CE CONSTRUCTEUR ET LES INSTRUCTIONS.
CAUTION
ADJACENT WALL
BACK WALL
D
A
SIDE WALL
BE
ADJACENT WALL
F
C
MUR COTE
MUR ARRIERE
MUR ADJACENT
MUR ADJACENT
LABEL LOCATION

PACIFIC ENERGY FIREPLACE PRODUCTS LTD.
2975 Allenby Rd., Duncan, BC V9L 4T8
Phone: [phone]
Web site: http://www.pacicenergy.net