Pacific energy Fusion User manual

070905-28 FSGA 5056.4221
INSTALLATION
and
OPERATING
INSTRUCTIONS
fusiongas
DIRECT VENT
FREESTANDING STOVE
Series A
IMPORTANT:
THESE INSTRUCTIONS ARETO
REMAIN WITH THE HOMEOWNER
– Do not store or use gasoline or
other flammable vapours and
liquids in the vicinity of this or
any other appliance.
– WHAT TO DO IFYOU SMELL GAS
•Do not try to light any appliance
•Do not touch any electrical
switch; do not use any phone in
your building
•Immediately call your gas supplier
from a neighbour’s phone. Follow
the gas supplier’s instructions
•If you cannot reach your gas
supplier, call the fire department
– Installation and service must be
performed by a qualified installer,
service agency or the gas supplier.
This appliance may be installed in
an aftermarket permanently
located, manufactured home (USA
only) or mobile home, where not
prohibited by local codes.
This appliance is only for use with
the type of gas indicated on the
rating plate. This appliance is not
convertible for use with other
gases, unless a certified kit is
used.
WARNING: If the information in
these instructions is not followed
exactly, a fire or explosion may
result causing property damage,
personal injury or loss of life.

2070905-28 FSGA 5056.4221
CAUTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
GAS SUPPLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
FLOOR PROTECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
ATTACHMENT TO FLOOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
CLEARANCES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
TOP OR REAR VENT CONVERSION . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-9
VENTING REQUIREMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
WALL TERMINATION VENTING- with no vertical rise . . . . . . . . . . . . . . . .10
WALL TERMINATION VENTING- with vertical rise . . . . . . . . . . . . . . . . . .11
ROOFTERMINATION VENTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
VENT TERMINAL CLEARANCES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
VENTING SYSTEM COMPONENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
REMOVAL OF WINDOW FRAME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
REMOVAL OF RIGHT HAND SIDE PANEL . . . . . . . . . . . . . . . . . . . . . . . . .15
ADJUSTMENT OF TOP VENT DAMPER . . . . . . . . . . . . . . . . . . . . . . . . . . .16
LOG SET INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
LIGHTING INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
FIRST FIRE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
MANUAL OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
OPTIONAL REMOTE CONTROL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
OPTIONAL BLOWER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
PROPANE CONVERSION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22-23
BODY REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
BURNER REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
SAFETY LABEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
NOTES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Contents

3
070905-28 FSGA 5056.4221
FORYOUR SAFETY
Do not install or operate your Pacific
Energy heater without first reading
and understanding this manual. Any
installation or operational deviation
from the following instructions voids
the Pacific Energy Warranty and may
prove hazardous.
This appliance and its individual
shutoff valve must be disconnected
from gas supply piping system during
any pressure testing of that system at
test pressures in excess of 1/2 psig.
(3.5 kpa).
This appliance must be isolated from
the gas supply piping system by
closing its individual manual shutoff
valve during any pressure testing of
the gas supply piping system at test
pressures equal to or less than 1/2
psig. (3.5 kPa).
This appliance must not be
connected to a chimney flue serving
a separate solid-fuel burning
appliance.
If the optional blower is installed, this
appliance must be electrically ground-
ed in accordance with local codes or,
in the absence of local codes, with
the National Electrical Code,
ANSI/NFPA 70, or the Canadian
Electrical Code, CSA C22.1.
Important: When lit for the first time, the appliance will emit a slight
odour for a couple of hours.This is due to the curing of paints, sealants
and lubricants used in the manufacturing process.This condition is
temporary. Open doors and windows to ventilate area. If optional fan kit
has been installed, place fan in the "OFF" position. Smoke and fumes
caused by the curing process may cause discomfort to some
individuals.
It is normal for fireplaces fabricated of steel to give off some expansion
and/or contraction noises during the start up or cool down cycle. Similar
noises are found with your furnace heat exchanger or cook stove oven.
Caution Fig. #1
7 5/8”
34”
18 5/8”
12 9/16”
26 7/16”
21”
Stove Dimensions
Center of top flue outlet
Center of rear
flue outlet

4070905-28 FSGA 5056.4221
• Due to high temperatures, this gas
appliance should be located out of
traffic and away from furniture and
draperies.
• Children and adults should be
alerted to the hazards of high surface
temperatures and should stay away
to avoid burns or clothing ignition.
• Young children should be carefully
supervised when they are in the
same room as the appliance.
• Clothing or other flammable material
should not be placed on or near the
appliance.
• Under no circumstances should this
fireplace be modified. Any grill, panel
or door removed for servicing the unit
must be replaced prior to operating.
Failure to do so may create a
hazardous condition.
• Installation and repair should be
done by a qualified service person.
The appliance should be inspected
before use and at least annually by a
professional service person. More
frequent cleaning may be required
due to excessive lint from carpeting,
bedding material, etc. It is imperative
that control compartments, burners
and circulating air passageways of
the appliance be kept clean.
It is Pacific Energy’s policy that no
responsibility is assumed by the
Company or by any of its employees
or representatives for any damages
caused by an inoperable, inadequate,
or unsafe condition, which is the
result, either directly or indirectly, of
any improper operation or installation
procedures.
Caution: Turn off gas and electrical
power supply and allow ample time
for unit to cool before servicing
appliance. It is recommended that
this appliance and venting should be
inspected at least once a year by a
qualified service person.
Do not use this heater if any part has
been under water. Immediately call a
qualified service technician to inspect
the heater and to replace any part of
the control system or gas control,
which has been under water.
Door Glass
Warning: Do not operate appliance
with glass panel removed, cracked
or broken. Replacement of glass
should be done by a licensed or
qualified service person.
Do not strike or otherwise impact the
glass in anyway that may cause it to
break. If the glass becomes cracked
or broken, it must be replaced before
using the fireplace. Replacement
glass can be obtained from your
nearest Pacific Energy dealer. Use
ceramic glass only. Do not substitute
with any other type.The size required
is 12 3/16” x 17 1/4” x 5 mm.
To remove broken glass, see page 11
for window removal instructions.
Remove all particles of glass. Be
careful, as they are very sharp. Install
new glass complete with gasket and
frame.
Annual Inspection:
a) Clean air passageways of
excessive lint and dust buildup from
carpeting, bedding material, etc.
The flow of ventilation air must not
be obstructed.
b) Inspect logs and burner
assembly for lint and soot build-up.
If excessive build-up of soot is pres-
ent, have a qualified service person
inspect and adjust unit for proper
combustion. Clean logs and burner
with a vacuum cleaner, paying close
attention to the ports on the burner.
c) Check the pilot system for proper
flame size and operation. Clean
pilot free of lint and dust.
(See Fig. #2)
d) Check that the vent pipe and
vent terminal are open and free
from blockage or debris. If the
venting system is disassembled for
cleaning, it must be properly
assembled and re-sealed, as per
vent manufacturers instructions.
e) Check door and glass panel
gasket, replace if necessary. It is
important that the glass and door
seal be maintained in good
condition.
Note: The appliance area must be
kept clear and free from
combustible materials, gasoline and
other flammable vapours and
liquids.
Periodically:
a) Viewing glass may be cleaned
with fireplace glass cleaner.
b) Exterior finish may be cleaned
with mild soap and water.
Safety Maintenance
Fig. #2 THERMOCOUPLE
ELECTRODE
PILOT FLAME
Caution:
Do not use abrasive cleaners
on glass or any other part of
this appliance.
Do not clean glass when hot.

5
070905-28 FSGA 5056.4221
Gas Supply
Floor Protection
Clearances
Attachment
to Floor
In the state of Massachusetts, only a
licensed plumber and gas fitter may
install this product. Correct gas line
diameter must be used to assure
proper operation.
The gas control is equipped with a
captured screw type pressure test
point, therefore it is not necessary to
provide a 1/8 inch N.P.T. plugged
tapping pressure test port for
checking gas pressure immediately
upstream of the gas supply
connection to the appliance.
The gas valve inlet accepts a 3/8"
N.P.T. fitting.
Mobile Home installations require that
the appliance be firmly attached to
the structure. Once the appliance is in
its final location, secure the unit in
place through holes in the pedestal
base.The holes are located on the
left and right hand side of the base.
The Fusion Gas stove may be
installed directly on a combustible
floor. If the appliance is to be installed
directly on carpeting, combustible
floor tile or other combustible material
other than wood flooring, the
appliance shall be installed on a
metal or wood panel extending the
full width and depth of the unit.
The minimum clearances from the
appliance to combustibles are shown
on Fig. #3. Adequate clearances
around air openings are required.
Sidewall to Appliance 6 in (152 mm)
Rearwall to Appliance 1 in (25 mm)
Corner to Appliance 1 in (25 mm)
Alcove Sidewall to Appliance 6 in (152 mm)
Alcove minimum width 33 in (838 mm)
Alcove maximum depth 48 in (1219 mm)
Alcove minimum height 46 in (1168 mm)
Minimum Clearances to Combustibles
Correct gas pressure requirements
Natural Gas Propane
Min. Pressure 5.0” WC 11.5” WC
(For purpose of
input adjustment)
Max. Pressure 13.9” WC 13.9” WC
Manifold Pressure
Maximum 3.8” WC 10.5” WC
Minimum 0.7” WC 1.6” WC
13 3/4”
1”
1”
Fig. #3
Caution:
The gas line should be installed
by a qualified service person in
accordance with all building
codes. Consult local and/or
national building codes before
proceeding.
1”
8 5/8”
16 1/2”
6”
8 5/8”
1”
6”
ALCOVE HEIGHT
61” MINIMUM
6”
48”

6070905-28 FSGA 5056.4221
Top or Rear Vent Conversion
1) Remove the two screws securing
the air deflector to the rear of the
stove (Fig. #3.01), remove the air
deflector and store it in a safe place
(Fig. #3.02).
2) Remove the two screws that
secure the top plate in place
(Fig. #3.03). To remove the top plate,
lift it from the back and slide it for-
ward slightly to unhook it from the
brackets at the front (Fig. #3.04).
The fusion gas stove is set up in the
factory as a top vent. To convert to
rear vent, use the following proce-
dure. Please read the instructions
carefully before converting the appli-
ance:
Fig. #3.01
Fig. #3.02
Fig. #3.03
Fig. #3.04

7
070905-28 FSGA 5056.4221
IMPORTANT:
Take care not to damage the
gaskets on the vent adapter
and flue outlet cover plate
during the procedure. Inspect
the gaskets carefully before
reinstalling, if the gasket on
either piece is damaged, it
will need to be replaced
before continuing.
3) Remove the four screws that fas-
ten the vent cover to the back of the
appliance, and remove the vent cover
(Fig. #3.05).
4) Remove the four screws securing
the vent adapter to the top of the
stove (Fig #3.06). Pull the vent
adapter off and attach it to the rear
flue outlet. Press firmly to ensure a
positive, snug connection (Fig. #3.07)
and use four screws to fasten it in
place (Fig. #3.08).
Fig. #3.05
Fig. #3.06
Fig. #3.07
Fig. #3.08

8070905-28 FSGA 5056.4221
5) Place the vent cover from step 3
over the top flue outlet (Fig. #3.09)
and use four screws to fasten it in
place (Fig. #3.10).
6) Replace the top plate by hooking
the front flange over the mounting
brackets (Fig. #3.11) pull it firmly
towards the rear of the appliance and
fasten it down at the back with two
screws (Fig #3.12).
Fig. #3.09
Fig. #3.10
Fig. #3.11
Fig. #3.12

9
070905-28 FSGA 5056.4221
7) Place the air deflector back on the
top of the appliance and align it so it
is spaced evenly from either side.
Fasten the air deflector to the rear
bracket using two screws (Fig. #3.13).
8) Place the optional cast iron Fusion
Gas Trivet into the outlet of the air
deflector.Take care to not scratch the
finish on the top of the appliance (Fig.
#3.14). Adjust the cap so that the
logo reads left to right when facing
the front of the appliance, and the
radius matches the top of the air
deflector.
Fig. #3.13
Fig. #3.14

10 070905-28 FSGA 5056.4221
The Fusion Gas stove installation and
venting must conform with local
codes or, in the absence of local
codes, to the current Installation
Code, CAN/CGA-B149.1 in Canada
or the current National Fuel Gas
Code, ANSI Z223.1 in the USA. Only
qualified (licensed or trained)
personnel should install this product.
The Fusion Gas Heaters are tested
and certified for use with SIMPSON
DURA-VENT DIRECT VENT GS pipe
or SECURITY CHIMNEYS SECURE
VENT system.Vent components
approved for use are listed on page
14. Kits for venting either through the
wall or vertically through the roof are
available from the vent system
manufacturer or your nearest Pacific
Energy Authorized Dealer. Before
installing the vent system, the
installer should read these
instructions to ensure proper
installation requirements are
maintained.
NO OTHER VENTING SYSTEMS OR
COMPONENTS MAY BE USED.
CAUTION: UNDER NO CONDITION
SHOULD COMBUSTIBLE
MATERIAL BE CLOSER THAN 1
INCH FROM ANY VERTICAL OR
HORIZONTAL VENT SECTIONS.
Venting must be installed as per the
venting manufacturers instructions –
see information supplied with the vent
system.
Consult your local Building Codes
before beginning the installation.
Venting
Requirements Venting For Wall Termination With No Vertical Rise
Maximum vent length is 24".
14" Snorkel Vent Terminal
must be used for all rear
vent applications. Where the
terminal is accessible a
guard, such as Simpson
Dura-vent part # 984SG,
must also be used.
Maximum of one 45° elbow may
be used, but the maximum vent
length must be reduced to 18".
14" Snorkel Vent Terminal must
be used for all rear vent
applications.Where the terminal
is accessible a guard, such as
Simpson Dura-vent part # 984SG,
must also be used.
Fig. #4
Fig. #5
24”
18”
14” Snorkel
termination
14” Snorkel
termination

11
070905-28 FSGA 5056.4221
Venting For Wall
Termination With
Vertical Rise
Any combination of rise and run may
be used but must be constrained to
the boundaries of this chart. For
each additional 90° elbow, reduce
vent length by 2 feet. For each
additional 45° elbow, reduce vent
length by 1 foot.
For optimum performance and flame
appearance, keep the vent length to a
minimum. Connections between
each vent component must be tightly
joined and sealed as per
manufacturer’s instructions.
1’ 2’ 3’ 4’ 5’ 6’ 7’ 8’ 9’ 10’
10’
9’
8’
7’
6’
5’
4’
3’
2
1’
24”
43”
Fig. #6 WALL TERMINATION VENT CHART

12 070905-28 FSGA 5056.4221
Roof
Termination
Venting
Any combination of rise and run may
be used but must be constrained to
the bounaries of this chart. If more
than 2 elbows are used, reduce
horizontal run by 2 feet for each
additional elbow.
For optimum performance and flame
appearance, keep the vent length to a
minimum. Connections between
each vent component must be tightly
joined and sealed. A horizontal run of
vent must have a 1/4-inch rise for
every 1-foot of run towards the
termination.
3’ 4’ 5’ 6’ 7’ 8’ 9’ 10’ MAX
10’
9’
8’
7’
6’
5’
2’
MIN
35’
40’
30’
Fig. #7 ROOF TERMINATION VENT CHART

13
070905-24 FSGA 5056.4221
Vent Terminal
Clearances
Minimum clearances to the vent
terminal must be maintained as
shown in Fig #8 and Fig #9. Measure
clearances to the nearest edge of
termination hood.
NOTE: Vent terminal must not be
recessed into a wall or siding.
Follow vent terminal manufactur-
ers installation instructions.
NOTE: LOCAL CODES OR
REGULATIONS MAY REQUIRE
DIFFERENT CLEARANCES.
D
V
V
E
B
L
V
V
V
V
V
X
B
B
B
B
C
F
V
X
V
A
J
B
G
V
I
H
M
X
K
Fig. #8
Fig. #9
Canadian Installation 1US Installation 2
A = Clearance above grade, verandah, porch, deck, or balcony. 12 inches (30 cm) 12 inches (30 cm)
B = Clearance to window or door that may be opened. 12 inches (30 cm) 9 inches (23 cm)
C = Clearance to permanently closed window (condensation). 12 inches (30 cm) 9 inches (23 cm)
D = Clearance to ventilated soffit located above the terminal within a horizontal distance of 2’ (61 cm) 12 inches (30 cm) 12 inches (30 cm)
from center-line of terminal.
E = Clearance to unventilated soffit. 12 inches (30 cm) 12 inches (30 cm)
F = Clearance to outside corner. 12 inches (30 cm) 12 inches (30 cm)
G = Clearance to inside corner. 12 inches (30 cm) 12 inches (30 cm)
H = Clearance to each side of center-line extended above meter/regulator assembly. 3 feet (91 cm) within height of 15
feet (4.5 m) above meter/regulator
I = Clearance around service regulator vent outlet. 3 feet (91 cm)
J = Clearance to non-mechanical air supply inlet to building, or the combustion air inlet to any 12 inches (30 cm) 9 inches (23 cm)
other appliance.
K = Clearance to a mechanical air supply inlet. 6 feet (1.83 m) 3 feet (91 cm) above if within
10’ (3m) horizontally
L = Clearance above paved sidewalkor a paved driveway located on public property 7 feet (2.13 m) †
M = Clearance under verandah, porch, deck or balcony. 12 inches (30 cm) ‡ 12 finches (30 cm) ‡
1In accordance with the current CSA B149.1, Natural Gas and Propane Installation Code
2In accordance with the current ANSI Z223.1/NFPA 54, National Fuel Gas Code
† A vent shall not terminate directly above a sidewalk or paved driveway which is located between two single family dwellings and serves both dwellings.
‡ Permitted only if veranda, porch, deck or balcony is fully open on a minimum of 2 sides beneath the floor.
* Clearance in accordance with local installation codes and the requirements of the gas supplier.
24”
(61 cm)
48”
(122 cm)
36”
(91.5 cm) 24”
(61 cm)
*
*
*
VENT TERMINAL AIR SUPPLY INLET AREA WHERE TERMINAL IS NOT PERMITTED
INSIDE
CORNER
DETAIL
FIXED
CLOSED FIXED
CLOSED
OPERABLE OPERABLE
VENT TERMINAL MINIMUM CLEARANCES
VENT TERMINAL MINIMUM
CLEARANCES TO
ADJACENT STRUCTURES
ADJACENT
STRUCTURES
OR FENCE

14 070905-28 FSGA 5056.4221
Venting System Components
DURAVENT GS SECURE VENT
galv. black galv. black
6" Pipe Length 908 908B SV 4 L6 SV 4 LB6
9" Pipe Length 907 907B
12" Pipe Length 906 906B SV 4 L12 SV 4 LB12
24" Pipe Length 904 904B SV 4 L24 SV 4 LB24
36" Pipe Length 903 903B SV 4 L36 SV 4 LB36
48" Pipe Length 902 902B SV 4 L48 SV 4 LB48
1 1/2" - 6" Adjustable Pipe Length SV 4 LA SV 4 LBA
12" Adjustable Pipe Length SV 4 LA12 SV 4 LBA12
11" - 14 5/8" Adjustable Pipe Length 911 911B
90° Elbow 990 990B SV 4 E45 SV 4 EB45
45° Elbow 945 945B SV 4 E90 SV 4 EB90
Termination Cap (Vertical) SV 4 CGV
High Wind Termination Cap (Vertical) 991
Low Profile Termination Cap (Vertical) 980
Extended Termination Cap (Vertical) 930
Horizontal Square Termination Cap 984 SV 4 CHC
Snorkel Termination Cap - 36" 981 SV 4 STC36
Snorkel Termination Cap - 14" 982 SV 4 STC14
Vinyl Siding Standoff 950
Vinyl Shield Protector SV 4 VS
Round Ceiling Support/Wall Thimble 940
Cathedral Ceiling Support Box 941
Adjustable Square Cathedral Ceiling Support SV 4 CSB
Collar for Square Cathedral Ceiling Support SV 4 AC
Decorative Black Plate (square) SV 4 PF
Universal Support SV 4 SU
Floor Support SV 4 SD
Roof Brace SV 4 BS
Ceiling Firestop 963 SV 4 BF
Insulated Attic Radiation Shield SV 4 RSA
Storm Collar 953 SV 4 FC
Flat Roof Flashing (c/w storm collar) SV 4 F
Roof Flashing 0/12 - 6/12 943
Roof Flashing 1/12 - 7/12 (c/w storm collar) SV 4 FA
Roof Flashing 7/12 - 12/12 943S
Roof Flashing 8/12 - 12/12 (c/w storm collar) SV 4 FB
Wall Straps 988 SV 4 BM
Wall Radiation Shield SV 4 RSM
Wall Thimble 942

1) Grasp the bottom of the door skin and
pull sharply forward and up to unhook
from the clip on the lower edge (Fig. #10).
2) Insert the handle provided into the
latch mechanism located approximately
two inches down from the top of the
window frame (Fig #11).
3) Repeat on other side
4) Swing the window frame out at the top
and lift out of the location rail along the
bottom edge of the firebox (Fig #12).
15
070905-28 FSGA 5056.4221
Removal of Window Frame Removal of Right
Hand Side panel
1) Remove the two screws securing the
panel to the firebox (Fig #13).
2) Unhook from the two tabs on the rear
and remove from firebox.
Fig. #10
Fig. #11
Fig. #12
Fig. #13

16 070905-28 FSGA 5056.4221
This appliance has a built in manual
damper that must be set dependant
on the height of the vent.
For recommended setting see
Fig #14.
The damper only applies to top
venting and is preset to 0º (fully
opened) at the factory.
To adjust vent damper:
1) If not already removed, remove
right hand side panel, see previous
section.
2) Loosen the screw in the securing
bracket and rotate to the
recommended setting (Fig #15).
3) Tighten screw and reassemble the
side panel.
Adjustment of Top Vent Damper
70˚
70˚
50˚
30˚
0˚
3’ 4’ 5’ 6’ 7’ 8’ 9’ 10’ MAX
MIN
MAX
15’
14’
13’
12’
11’
10’
9’
8’
7’
6’
5’
4’
3’
2’
1’
0’
40’
35’
30’ 30’
15’
7’
4’
ALL INSTALLATION ON THIS
LINE MUST BE SET TO ‘0’
Fig. #14
Fig. #15
90˚ (Closed)
70˚
50˚
30˚
0˚ (Open)
Securing
Bracket
TIP
Check inside top flue outlet first
to see position of damper. It may
not be necessary to remove
right hand side panel to adjust.

17
070905-28 FSGA 5056.4221
Log Set Installation
The ceramic logs are durable and
long lasting when installed properly.
However, they are delicate and may
be damaged easily if not handled with
care.
Unpack and inspect log set.There
should be a total of 2 logs and one
base ceramic. Gas and vent
connections should be made before
installing logs.
Position the logs as indicated by Figs.
#16 to #18.
Note: Improper placement of logs
may cause sooting on internal
parts and glass.
Place the Base Ceramic (5097.26105) in the bottom of the firebox. Pull toward the
burner until it hits the ceramic spacer and then centralize to the burner.
Place Left Hand Log
(5097.22) over pin in
Base Ceramic and then
line up the front face of
the log with the corner
of the ash bed char
effect (Fig #17).
Place the Right Hand
Log (5097.24) as per
Fig. #18 .
Final log
positions (Fig. #18).
Fig. #16
Fig. #17
Fig. #18

18 070905-28 FSGA 5056.4221
Lighting Instructions

19
070905-28 FSGA 5056.4221
First Fire Manual
Operation
When lit for the first time, the appli-
ance will emit a slight odour for a
couple of hours. This is due to the
curing of paints, sealants and
lubricants used in the manufacturing
process. This condition is temporary.
Open doors and windows to ventilate
area. If optional fan kit has been
installed, place fan in the "OFF"
position. Smoke and fumes caused
by the curing process may cause
discomfort to some individuals.
It is normal for fireplaces fabricated of
steel to give off some expansion
and/or contraction noises during the
start up or cool down cycle. Similar
noises are found with your furnace
heat exchanger or cook stove oven.
See lighting instructions on page 18.
Once the burner has been lit, the
flame height can be adjusted by
rotating the flame adjustment knob.
Rotate the knob fully counter-
clockwise to give the high setting and
fully clockwise for the low setting.
Extended Shutdown:
To shutdown the appliance including
the pilot, partially depress and turn
gas valve knob clockwise past
"PILOT" to "OFF" position. DO NOT
FORCE.
NOTE: The control has an
interlock device which does not
allow the pilot to be lit when the
appliance is at operating
temperature. Let the appliance
cool down (approx. 60 sec.) before
attempting to relight the pilot.
DO NOT use force to rotate the
control knob.
Fig. #19
Fig. #19

20 070905-28 FSGA 5056.4221
The Fusion Gas Stove can be
equipped with a thermostatic remote
control. Once a pilot light has been
established, and the gas control knob
turned to the "ON" position, the
burner may be turned on or off simply
with the remote control.
The remote can be operated in three
ways.
1) Manual operation
Simply press the large "UP" or
"Down" buttons; the word "Man" as
well as a large arrow in the upper left
corner will be displayed.
To raise the flame press the "up"
button, and to lower the flame press
the "down". In this mode the "auto"
and "Timer" functions are overridden.
2) Auto / Thermostatic Operation
Push and hold the "Auto" button until
the temperature reading on the hand
set display flashes.While it is flashing
push the large "up" and "down"
buttons until the desired temperature
is displayed, wait until the
temperature stops flashing.The
remote will now check the
temperature of the room every five
mins and adjust the fire to up or down
to suit the temperature you have set.
3) Timer setting
The third option is to program the
fireplace to operate at set times. It
has two "on" and "off" cycles which
allows you to program the fire to
come on just before you get up, shut
down just after you leave, be on
again when you get back and then
shut down for the night.
Program this feature as follows:
a) Set the temperature as per (2),
Auto / Thermostatic operation, if not
already done.
b) Press and hold the "timer" button
and it down until "P1*" is displayed in
the handset.When its flashing press
the large up and down buttons to set
the time you would like the fireplace
Optional Remote Control
to come on in the morning.
c) Press timer again and the "P1
(moon)" will appear, set the time you
wish the fireplace to go off when you
leave.
d) Press timer a third time "P2*" will
appear, this is the time you would like
the fireplace to come on when you
return, set this again by using the
large up and down buttons.
e) Press the "timer" button for the
fourth and final time, the "P2 (moon)"
appears, set the time you wish the
fireplace to go off in the evening
using the large "up" and "down"
buttons. Wait until the display stops
flashing.
The on /off times and temperature
are now set.The fireplace will come
on and off at the times you have set
and keep the room to the
temperature you set.
If you want to override the timer
feature, just press "auto" to put you
back into thermostat only setting or
the large up and down buttons to put
you in manual operation.
Fig. #20
Fig. #21
Fig. #22