Pakedge Device & Software RK-1 User manual

QUICK START GUIDE
RK-1
High Throughput - Dual WAN, Gigabit Audio/Video Router
Version 1.0
pakedgedevice&software inc

2
Contents
Overview 3
Package Contents 6
Installing the Router 6
Changing the Router Password 7
Accessing the Router GUI 7
Connecting to the Internet 7
Changing the LAN IP 12
Troubleshooting and Support 14

3
Overview
The RK-1 is an high power audio/video router that is designed to minimize installation
times through an intuitive GUI. See the Table 1 for more information.

4
Table 1: LED Explanation (From Left to Right)
Note: LAN Port number 5 can be congured as a Guest network. Please see the
user’s manual for additional information.
LED Status Operaon
USB 1 - 2 LINK/
ACT
Blue USB is connected
Flashing
Blue USB is being accessed
O No device connected
WAN 1 - 2 LINK/
ACT
Blue Port is online (link established)
Flashing
Blue Acvity
O No device connected
LAN 1 - 5 LINK/
ACT
Blue Port is online (link established)
Flashing
Blue Acvity
O No device connected
Power
Blue The router is powered on
O The router is turned o

5
You will nd a description of the interfaces on the back of the RK-1 in Table 2.
Table 2: Interface Explanation (From Left to Right)
Interface Type Speed Protocol Descripon
Reset Buon N/A N/A N/A Hold Reset Buon for 10 seconds to
factory default the sengs
USB 1 - 2 USB-A 5Gbps USB 3.0 USB port used for le sharing
WAN 1 - 2 RJ-45 10/100/1000
Mbps Ethernet WAN port used for the Internet connecon from the ISP
LAN (Ports 1-5) RJ-45 10/100/1000
Mbps Ethernet 5-port switch connecons on the internal network
Console RJ-45 115200 Console Console port for maintenance use
AC Power input AC N/A N/A Power Input
Power Switch N/A N/A N/A On/O Power Switch

6
Package Contents
RK-Router
Mounting Brackets
Power Cable
1ft CAT5E Cable
Quick Start Guide
Installing the Router
1. If mounting the router in a standard 19” AV rack, attach the rack-
mounting brackets that come with the router to the sides. If not rack-
mounting, ensure that the router is physically mounted near power and
network connections.
2. Connect power to the device.
3. Connect an Ethernet cable from your computer to any of the LAN ports
on the router.

7
Changing the Router Password
It is strongly recommended that you change the default password for the router. Please
refer to the user manual for step by step instructions.
Accessing the Router GUI
1. Make sure your network card is set to obtain an IP address automatically. Then open
any Internet browser and go to the address http://192.168.1.99 or you can simply
type pakedgerouter.com Note: For best results we recommend using Mozilla
Firefox as your web browser.
2. Enter the default username pakedge and the password pakedger. Click login.
Connecting to the Internet
The router supports the three main types of Internet connections:
• DHCP (Typically used by cable companies and DSL basic service)
• Static IP (Fixed public IP address mostly used by Business Class Broadband
services)
• PPPoE (Used by DSL companies such as AT&T)

8
Determine what type of Internet connection you have from your Internet Service Provider
(ISP), and then follow one of the three instruction sets below to connect the router to the
Internet.
DHCP:
By default, the router will connect to the Internet using DHCP. If your ISP uses DHCP, you
may need to reset the modem to get Internet access. If you are using a modem that has a
router built into it, you may have to congure DMZ settings to allow complete functionality
of the RK-1.
Static IP:
To congure the router to a static IP, complete the following steps:
1. Hover your mouse towards the top of page to see the menu. Click on Network
Zones.

9
2. Click on Edit under WAN zone.
3. Select Static Address for the Protocol.

10
4. Click on Switch Protocol.
5. Enter the IP address from your ISP. Select the appropriate Subnet Mask from
your ISP. You can select custom to enter a custom subnet mask. Then enter your
Default Gateway and DNS Server. Leave the override MAC address at default.
Click Apply. The router now has the Static IP congured on it.

11
PPPoE:
To congure the router using a PPPoE connection, you will need to complete the following
steps:
1. Hover your mouse towards the top of page to see the menu. Click on Network
Zones.
2. Click on Edit under WAN zone.
3. Select PPPoE from the Protocol drop down menu. Then click on Switch Protocol.

12
4. Enter the username that the ISP assigned under the PAP/CHAP username eld.
Enter the password in the PAP/CHAP password eld. Click Apply when nished.
The router is now setup for PPPoE.
Changing the LAN IP
The default IP address of the router is 192.168.1.99. If you need to change the IP address of
the router or change the entire network address take the following steps.
1. Click on Network Zones.

13
2. Click Edit under LAN zone.
3. Enter the new IP address you wish to use in the IP Address eld. In the following
example we change the IP address of the router to 192.168.1.1.
4. Click Apply towards the bottom to nalize the settings.

14
Troubleshooting and Support
If you are unable to get the router functional using these steps, you can refer to the full
manual on our website or contact the Technical Support Team for assistance.
Contact information
Website: www.pakedge.com
Email: [e-mail]
Phone: [phone]
© Pakedge Device & Software Inc. 2015 – All Rights Reserved
pakedgedevice&software inc
3847 Breakwater Avenue
Hayward,CA 94545
Main: 650-385-8700
Fax: [phone]