Panasonic CS-NS12UKY Series User manual

CS-NS12UKY series
CS-NS18UKY series
CS-NS24UKY series
CS-WS12UKY series
CS-WS18UKYA series
CS-WS18UKYE series
CS-WS18UKYS series
CU-NS12UKY series
CU-NS18UKY series
CU-NS24UKY series
CU-WS12UKY series
CU-WS18UKYA series
CU-WS18UKYE series
CU-WS18UKYS series
ACXF55-19980-AC
English
Operating Instructions
Air Conditioner
Thank you for purchasing Panasonic Air Conditioner.
Installation instructions attached.
Before operating the unit, please read these operating
instructions thoroughly and keep them for future
reference.
C
SLEEP/
SLEEP/
POWERFUL
POWERFUL
nanoe-G
nanoe-G
PURIFIER
PURIFIER
ACXF55-1998OL.ai16/1/201812:51:08PMACXF55-1998OL.ai16/1/201812:51:08PM

ACXF55-1998OL.ai26/1/201812:51:20PMACXF55-1998OL.ai26/1/201812:51:20PM

POWER
•Please note that the
indication is on display to
start the unit.
3Select the desired
temperature
•Selection range:
16 °C ~ 30 °C.
•
Operating the unit within the
recommended temperature
range may save energy.
COOL: 26 °C ~ 28 °C.
DRY : 1 °C ~ 2 °C lower than
room temperature.
•Use remote control within 8 m
from the remote control receiver
of the indoor unit.
Safety precautions.......................4-5
How to use...................................6-7
Cleaning instructions......................
.............................
8
Troubleshooting 9
FAN DRY
8m
1
3
2
POWERFUL/
DISPLAY
QUIET
nanoe-G
2
1
3
BEE Regulation.............................10
Information....................................11
ACXF55-1998OL.ai36/1/201812:51:21PMACXF55-1998OL.ai36/1/201812:51:21PM

4
Safety precautions
To prevent personal injury, injury to others
or property damage, please comply with the
following:
Incorrect operation due to failure to follow
instructions below may cause harm or damage,
the seriousness of which is classified as below:
WARNING This sign warns of
death or serious
injury.
CAUTION This sign warns of
injury or damage to
property.
The instructions to be followed are classified by
the following symbols:
This symbol denotes an
action that is PROHIBITED.
These symbols denote
actions COMPULSORY.
Indoor unit
Outdoor unit
Power supply
Remote control
Air inlet
Air inlet
Air inlet
Air inlet
Air outlet
Air outlet
Air outlet
Air outlet
WARNING
Indoor unit and outdoor unit
This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience
and knowledge, unless they have been given
supervision or instruction concerning use of the
appliance by a person responsible for their safety.
Children should be supervised to ensure that they
do not play with the appliance.
Please consult authorised dealer or specialist to
clean the internal parts, repair, install, remove and
reinstall the unit. Improper installation and handling
will cause leakage, electric shock or fire.
Confirm with authorised dealer or specialist on
usage of any specified refrigerant type.
Using refrigerant type other than the specified may
cause product damage, burst and injury etc.
Do not install the unit in a potentially explosive or
flammable atmosphere. Failure to do so could result
in fire.
Do not insert your fingers or other objects
into the air conditioner indoor or outdoor
unit, rotating parts may cause injury.
Do not touch the outdoor unit during lightning, it
may cause electric shock.
Do not expose yourself directly to cold air for a long
period to avoid excess cooling.
Do not sit or step on the unit, you may fall
down accidentally.
Remote control
Do not allow infants and small children to play with
the remote control to prevent them from accidentally
swallowing the batteries.
Power supply
Do not use a modified cord,
joint cord, extension cord or
unspecified cord to prevent
overheating and fire.
To prevent overheating, fire or electric shock:
• Do not share the same power outlet with other
equipment.
• Do not operate with wet hands.
• Do not over bend the power supply cord.
• Do not operate or stop the unit by inserting or
pulling out the power plug.
ACXF55-1998OL.ai46/1/201812:51:21PMACXF55-1998OL.ai46/1/201812:51:21PM

English
5
Safety precautions
Use complete power supply cord without joining.
In unavoidable circumstances that complete
power supply cord without joining is impossible,
use an approved connection means (for
example: socket and plug).
Air Conditioner
Complete wire
without joining
Approved connecting
means (for example:
approved socket and
plug)
Complete
wire without
joining
Power
Supply
OR
Indoor Unit
Outdoor
Unit
If the supply cord is damaged, it must be
replaced by the manufacturer, service agent or
similarly qualified persons in order to avoid a
hazard.
It is strongly recommended to be installed
with Earth Leakage Circuit Breaker (ELCB)
or Residual Current Device (RCD) to prevent
electric shock or fire.
To prevent overheating, fire or electric shock:
• Insert the power plug properly.
• Dust on the power plug should be periodically
wiped with a dry cloth.
Stop using the product if any abnormality/failure
occurs and disconnect the power plug or turn off
the power switch and breaker.
(Risk of smoke/fire/electric shock) Examples of
abnormality/failure
• The ELCB trips frequently.
• Burning smell is observed.
• Abnormal noise or vibration of the unit is
observed.
• Water leaks from the indoor unit.
• Power cord or plug becomes abnormally hot.
• Fan speed cannot be controlled.
• The unit stops running immediately even if it is
switched on for operation.
• The fan does not stop even if the operation is
stopped.
Contact your local dealer immediately for
maintenance/repair.
This equipment must be earthed to prevent
electrical shock or fire.
Prevent electric shock by switching off the power
supply and unplug:
- Before cleaning or servicing,
- When extended non-use, or
- During abnormally strong lightning activity.
CAUTION
Indoor unit and outdoor unit
Do not wash the indoor unit with water,
benzine, thinner or scouring powder to avoid
damage or corrosion at the unit.
Do not use for preservation of precise equipment,
food, animals, plants, artwork or other objects.
This may cause quality deterioration, etc.
Do not use any combustible equipment in front of
the airflow outlet to avoid fire propagation.
Do not expose plants or pet directly to airflow to
avoid injury, etc.
Do not touch the sharp aluminium fin,
sharp parts may cause injury.
Do not switch ON the indoor unit when waxing
the floor. After waxing, aerate the room properly
before operating the unit.
Do not install the unit in oily and smoky areas to
prevent damage to the unit.
Do not dismantle the unit for cleaning purpose to
avoid injury.
Do not step onto an unstable bench when
cleaning the unit to avoid injury.
Do not place a vase or water container on the
unit. Water may enter the unit and degrade the
insulation. This may cause an electric shock.
Do not open window or door for long time
during COOL/DRY mode operation.
Prevent water leakage by ensuring drainage
pipe is:
- Connected properly,
- Kept clear of gutters and containers, or
- Not immersed in water
After a long period of use or use with any
combustible equipment, aerate the room
regularly.
After a long period of use, make sure the
installation rack does not deteriorate to prevent
the unit from falling down.
Remote control
Do not use rechargeable (Ni-Cd) batteries. It may
damage the remote control.
To prevent malfunction or damage of the remote
control:
• Remove the batteries if the unit is not going to
be used for a long period of time.
• New batteries of the same type must be
inserted following the polarity stated.
Power supply
Do not disconnect the plug by pulling the cord to
prevent electric shock.
ACXF55-1998OL.ai56/1/201812:51:21PMACXF55-1998OL.ai56/1/201812:51:21PM

How to use
Auto OFF/ON buttonTo adjust horizontal airflow direction Use when remote control is
misplaced or a malfunction
occurs. Raise the front panel:
•To use in AUTO mode, press
the button once.
•To use in COOL mode, press
and hold the button until 1 beep
is heard, then release.
•Press the button again to turn
off.
•Manually adjustable.
Remote control
receiver
POWERFUL/
DISPLAY
QUIET
nanoe-G
Press and hold for
approximately
10 seconds to show
temperature setting in
°C or °F.
Press to restore the
remote control to
default setting.
Not used in normal
operations.
POWER (Yellow Green)
TIMER
SLEEP /
POWERFUL
nanoe-G
PURIFIER
(Orange)
(Blue)
(Orange /
Yellow Green)
Remote control
display
6
To maximise comfort while
sleeping
• This operation provides you with a comfortable
environment while sleeping by gradually increase
the set temperature 1 °C after every 3 hours operation.
• The unit is turned off after 8 hours.
• Can be cancelled by pressing the respective
button again.
SLEEP /
POWERFUL
To switch between POWERFUL
and QUIET mode
POWERFUL: To reach set temperature quickly
SLEEP /
POWERFUL
• This operation stops automatically after 1 hours.
QUIET: To enjoy quiet operation
• This operation reduces airflow noise.
POWERFUL/
QUIET
To OFF/ON hidden temeprature
display
• You can turn OFF/ON the hidden temperature
display during sleeping hours for comfort.
• Hidden display is ON by default all time when unit
is switched on.
DISPLAY
To select operation mode
AUTO - For your convenience
COOL - To enjoy cool air
DRY - To dehumidify the environment
Unit will select a standard temperature
of 25 °C.
Fan speed and swings will operate in Auto mode.
You can change the temperature according to
your comfort.
To reduce power consumption during COOL mode,
use curtains to screen off sunlight and outdoor heat.
Unit operates at low fan speed to give a gentle
cooling operation.
FAN - To operate Air-Con in “Fan Only” mode
* Indoor unit temp. display will show set temp. for
AUTO,COOL & DRY mode and room temp. for FAN
mode.
Unit operates without running compressor with
Indoor unit fan running as per remote setting fan
speed and air flow direction.
C
SLEEP/
SLEEP/
POWERFUL
POWERFUL
nanoe-G
nanoe-G
PURIFIER
PURIFIER
ACXF55-1998OL.ai66/1/201812:51:22PMACXF55-1998OL.ai66/1/201812:51:22PM

English
7
How to use
To adjust airflow direction
(Remote control display)
•Keeps the room ventilated.
•In COOL/DRY mode, if AUTO is set, the flaps
swings up/down automatically.
•The vertical flap are fixed at the predetermined
position.
•Do not adjust the flap by hand.
To set the timer
To turn ON and OFF the unit at a preset times.
12 3
1Select ON or OFF
timer Example: OFF at 22:00
•Each time pressed:
Cancel
2Set the time
3Confirm
TIMER
•To cancel ON or OFF timer, press or
then press .
•If timer is cancelled manually or due to power
failure, you can restore the timer again by
pressing or then press .
•The nearest timer setting will be displayed and
will activate in sequence.
•When ON Timer is set, the unit may start
earlier (up to 15 minutes) before the actual
set time in order to achieve the desired
temperature on time.
•Timer operation is based on the clock set in
the remote control and repeats daily once set.
For clock setting, please refer to Quick guide.
Auto Restart Control
•If power is resumed after a power failure, the
operation will restart automatically after a period
of time with previous operation mode and airflow
direction.
•This control is not applicable when TIMER is set.
To select fan speed
(Remote control display)
AUTO
FAN
•ForAUTO, the indoor fan speed is automatically
adjusted according to the operation mode.
Operation conditions
Use this air conditioner under the following
temperature range.
DBT : Dry bulb temperature
WBT : Wet bulb temperature
50 30
•nanoe-G starts automatically when the unit is
turned on with .
•Can be activated even when the unit is turned
off. In this condition, the unit will operate as a fan
with AUTO fan speed and louver swing.
nanoe-G
PURIFIER
nanoe-G
ACXF55-1998OL.ai76/1/201812:51:25PMACXF55-1998OL.ai76/1/201812:51:25PM

8
Cleaning instructions
To ensure optimal performance of the unit,
cleaning has to be carried out at regular
intervals. A dirty unit may cause malfunction.
Please consult authorised dealer.
•Switch off the power supply and unplug before
cleaning.
•Do not touch the aluminium fin, sharp parts may
cause injury.
•Do not use benzine, thinner or scouring powder.
•Use only soap ( pH 7) or neutral household
detergent.
•Do not use water hotter than 40 °C.
Indoor unit
Wipe the unit gently with a soft,
dry cloth.
Front panel
Wash gently and dry.
Remove the front panel
Raise
Pull out
1
2
Close it securely
Insert at both sides
1
2Close down
3Press both ends of the front panel
4For XS12M,XS18, XS24 series.
Press at center of the front panel.
PM 2.5 filter
•Clean the filter whenever necessary.
•Don’t wash/rinse the filter with water.
•The surface of the filter shouldn’t be rubbed
with any object.
•The filter shouldn’t be pulled with strong force
as it may get damaged.
For seasonal inspection after extended
non-use
•Checking of remote control batteries.
•No obstruction at air inlet and air outlet vents.
•UseAuto OFF/ON button to select COOL
operation. After 15 minutes of operation, it
is normal to have the following temperature
difference between air inlet and air outlet
vents: COOL: 8 °C
For extended non-use
•Activate nanoe-G operation for 2~3 hours as
an alternative to remove moisture left in the
internal parts thoroughly to prevent mould
growth.
•Turn off the power supply and unplug.
•Remove the remote control batteries.
nanoe-G Generator
Every 2 weeks
•Clean with dry cotton bud.
•Do not touch during operation.
Indoor unit
Front panel
Catechin filters
nanoe-G
Generator
Aluminium fin
PM 2.5 filters
Please remove the PM2.5 Filter before wash/rinse the filter
with water.
Catechin filters
Every 2 weeks
•Wash/rinse the filters gently with
water to avoid damage to the
filter surface.
•Dry the filters thoroughly under shade, away
from fire or direct sunlight.
•Replace any damaged filters.
Remove air filter Attach air filter
ACXF55-1998OL.ai86/1/201812:51:25PMACXF55-1998OL.ai86/1/201812:51:25PM

English
9
Troubleshooting
Cleaning instructions / Troubleshooting
NON SERVICEABLE CRITERIAS
TURN OFF POWER SUPPLY AND
UNPLUG then please consult authorised
dealer under the following conditions:
•Abnormal noise during operation.
•Water/foreign particles have entered the
remote control.
•Water leaks from Indoor unit.
•Circuit breaker switches off frequently.
•Power cord becomes unnaturally warm.
•Switches or buttons are not functioning
properly.
The unit stops and the TIMER indicator blinks.
Use remote control to retrieve error code.
Press for
5 seconds
Press for
5 seconds
to quit
checking
Press until you
hear 4 beep sound,
then write down
the error code
Turn the unit off
and reveal the
error code to
authorised dealer
21
34
•
operation but if problem persist please consult authorised
dealer with error code.
For certain errors, you may restart the unit for limited
• For models with temp. display, error code will show
automatically.
ACXF55-1998OL.ai96/1/201812:51:26PMACXF55-1998OL.ai96/1/201812:51:26PM

10
BEE Regulation
Step a): Press and Hold the button on indoor unit.
Control button when display is showing
OFF, while holding the indoor unit button.
Step b): Within 5 second, press once the Remote
Turn on the main power supply to unit.•
•
•
Testing Guidelines
Cooling Test Mode for Full Load (100%) and
Half Load (50%)
1) Mode : Select ‘COOL’
2) Temperature : a) 16 ºC for Full Load (100%)
3) Air Swing
Vertical Airflow : Set vane position to 3rd step from top
: b) 17 ºC for Half Load (50%)
(For Full Load)
QUIET
CLEAN
Note: Unit is charged with extra 60g refrigerant for installation purging purpose.
For all laboratory tests, 60g shall be released to follow the rated refrigerant amount mentioned in nameplate.
Open the Front Panel by lifting Intake Grille.
Follow the below Instructions.
4) Air Swing
Horizontal Airflow
:
Set vane position to be
straight (For applicable Model)
5) Fan speed : Maximum
1
2
1
2
(For Half Load)
QUIET
CLEAN
1
2
1
2
(Indication for Half load)(Indication for Full load)
POWER
TIMER
nanoe-G
PURIFIER
SLEEP/
POWERFUL
POWER
TIMER
nanoe-G
PURIFIER
SLEEP/
POWERFUL
THREE LEDs FROM BOTTOM
STARTS BLINKING TWO LEDs FROM BOTTOM STARTS BLINKING
Step c): After hearing a beep sound from the Indoor
Unit, immediately release the (Auto OFF/ON)
button on Indoor Unit.
All this should be done within 5 seconds.
(Auto OFF/ON Button)
ACXF55-1998OL.ai106/1/201812:51:27PMACXF55-1998OL.ai106/1/201812:51:27PM

English Information / BEE Regulation
11
Information on hazardous constituents as specified in sub-rule1 of rule16 (1) in electrical and electronic
equipment.
Declaration of Conformity with the requirements of the E-Waste (Management) Amendment Rules 2018
with the rule 16 (1) limits with respect to Lead, Mercury, Cadmium, Hexavalent chromium, Polybrominated
biphenyls, Polybrominated diphenyl ethers.
The content of hazardous substance with the exemption of the applications listed in SCHEDULE II of the
E-Waste (Management) Amendment Rules 2018 :
1. Lead (Pb) – not over 0.1% by weight;
2. Cadmium (Cd) – not over 0.01% by weight;
3. Mercury (Hg) – not over 0.1% by weight;
4. Hexavalent chromium (Cr6+) – not over 0.1% by weight;
5. Polybrominated biphenyls (PBBs) – not over 0.1% by weight;
6. Polybrominated diphenyl ethers (PBDEs) – not over 0.1% by weight.
For the purpose of recycling to facilitate effective utilization of resources,
please return this product to a nearby authorized collection center,
registered dismantler of recycler, or Panasonic service center when
disposing of this product.
Customer care number ( Toll free ) : 1800 103 1333 ,1800 108 1333
Please see the Panasonic website for further information on collection centers, etc.
or call the customer care toll-free number
http://www.panasonic.com/in/corporate/sustainability/panasonic-india-i-recycle-program.html
S.No.
1. All electrical and electronic products are required
to be handed over only to the Authorized
recycler.
2. The product should be handed over only to
authorized recycler for disposal.
3.
4.
5.
6.
Keep the product in isolated area, after it
becomes non-functional / un-repairable so as to
prevent its accidental breakage.
Provide information on the catalogue with
product end-of-life.
Always dispose products that have reached
end-of life at Panasonic India Authorized Service
Centre.
Wherever possible or as instructed, separate the
packaging material according to responsible
waste disposal options and sorting for recycling.
The product is not meant for re-sale to any
unauthorized agencies / scrap dealer / kabari-
walas.
The product is not meant for mixing into house-
hold waste stream.
Do not keep any replaced spare part(s) from the
product in exposed area.
Do not donate old electronic items to any body.
Do not dispose your product in garbage bins
along with municipal waste that ultimately
reaches landfill.
Do not give e-waste to informal and unorganized
sectors like Local Scrap Dealer / Rag Pickers.
The product should not be opened by the User
himself / herself, but only by authorized service
personnel.
Do's Don't
Do’s & Don’t: E-waste (Management )Amendment Rules 2018
ACXF55-1998OL.ai116/1/201812:51:27PMACXF55-1998OL.ai116/1/201812:51:27PM

ACXF55-19980-AC
FT0218-0
Printed in India
Panasonic Corporation
Website: http://www.panasonic.com
© Panasonic Corporation 2018
ACXF55-1998OL.ai126/1/201812:51:27PMACXF55-1998OL.ai126/1/201812:51:27PM