Panasonic KX-MB778TW User manual

This unit is compatible with Caller ID. Please be sure that both your line and the other party’s line
support the Caller ID function.
Operating Instructions
Multi-Function Printer
Model No. KX-MB778TW
KX-MB788TW
Do NOT connect the USB cable until prompted by the Multi-Function Station (CD-ROM).
12
MB778-788TW-PFQX2765ZA-OI-en.PDF Page 1 Tuesday, July 31, 20073:30 PM

2
Thank you for purchasing a Panasonic Multi-
Function Printer.
Note:
LThe suffix in the model number will be omitted in
these instructions.
LMost figures shown in these operating instructions
are based on a KX-MB778.
Trademarks:
LMicrosoft, Windows, Windows Vista, Internet
Explorer and PowerPoint are either registered
trademarks or trademarks of Microsoft Corporation
in the United States and/or other countries.
LPentium is a registered trademark or trademark of
Intel Corporation in the United States and/or other
countries.
LScreen shots reprinted with permission from
Microsoft Corporation.
LAdobe and Reader are either registered trademarks
or trademarks of Adobe Systems Incorporated in the
United States and/or other countries.
LAvery is a registered trademark of Avery Dennison
Corporation.
LXEROX is a registered trademark of Xerox
Corporation.
LAll other trademarks identified herein are the
property of their respective owners.
Copyright:
LThis manual is copyrighted by Panasonic Systems
Sales Taiwan CO., Ltd. (PSST). Under the copyright
laws, this manual may not be reproduced in any form,
in whole or part, without the prior written consent of
PSST.
© 2007 Panasonic Communications Co., Ltd. All Rights
Reserved.
MB778-788TW-PFQX2765ZA-OI-en.book Page 2 Tuesday, July 31, 2007 3:30 PM

Important Information
3
Important InformationImportant Information
For best performance
Toner cartridge and drum unit
LWhen replacing the toner cartridge or drum unit, do
not allow dust, water, or liquids to come in contact
with the drum. This may affect print quality.
LFor optimal performance, genuine Panasonic toner
cartridges and drum units are recommended. We
cannot be responsible for problems that may be
caused by a non-Panasonic toner cartridge or drum
unit:
– Damage to the unit
– Poor print quality
– Improper operation
Toner cartridge
LDo not leave the toner cartridge out of the protection
bag for a long time. It will decrease the toner life.
Drum unit
LRead the instructions on page 9 before you begin
installation of the drum unit. After you have read
them, open the drum unit protection bag. The drum
unit contains a photosensitive drum. Exposing it to
light may damage the drum. Once you have opened
the protection bag:
– Do not expose the drum unit to light for more than
5 minutes.
– Do not touch or scratch the black drum surface.
– Do not place the drum unit near dust or dirt, or in
a high humidity area.
– Do not expose the drum unit to direct sunlight.
LTo extend the life of the drum unit, the unit should
never be turned OFF immediately after printing.
Leave the power turned ON for a minimum of 30
minutes after printing.
Location
LTo avoid malfunction, do not position the unit near
appliances such as TVs or speakers which generate
an intense magnetic field.
Static electricity
LTo prevent static electricity damage to the interface
connectors or other electrical components inside the
unit, touch a grounded metal surface before touching
the components.
Environment
LKeep the unit away from electrical noise generating
devices, such as fluorescent lamps and motors.
LThe unit should be kept free from dust, high
temperature and vibration.
LThe unit should not be exposed to direct sunlight.
LDo not place heavy objects on top of the unit. When
you leave the unit unused for a long period of time,
unplug this unit from the power outlet.
LThe unit should be kept away from heat sources such
as heaters, kitchen stoves, etc. Damp basements
should also be avoided.
LIn the printing process, heat is used to fuse toner
onto the page. As a result, it is normal for the
machine to produce an odour during and shortly after
printing. Be sure to use this unit in an area with
proper ventilation.
LDo not place any objects within 10 cm of the right, left
and back sides of the unit.
LDo not cover slots or openings on the unit. Inspect
the air circulation vents regularly and remove any
dust build-up with a vacuum cleaner (1).
Routine care
LWipe the outer surface of the unit with a soft cloth. Do
not use benzine, thinner, or any abrasive powder.
1
1
MB778-788TW-PFQX2765ZA-OI-en.book Page 3 Tuesday, July 31, 2007 3:30 PM

Table of Contents
4
1. Table of Contents
1. Introduction and Installation
Accessories
1.1 Included accessories..................................... 6
1.2 Accessory information................................... 6
Finding the Controls
1.3 Button descriptions........................................ 7
1.4 Overview ....................................................... 8
Installation
1.5 Toner cartridge and drum unit ....................... 9
1.6 Output tray................................................... 12
1.7 Recording paper.......................................... 13
2. Preparation
Connections and Setup
2.1 Connections ................................................ 15
2.2 Dialling mode............................................... 16
2.3 Selecting the operation mode (Scan/Copy/Fax)
.................................................................... 16
Document Requirements
2.4 Setting the original....................................... 17
Help
2.5 Help function ............................................... 18
Volume
2.6 Adjusting volume ......................................... 19
Initial Programming
2.7 Date and time .............................................. 19
2.8 Your logo...................................................... 20
2.9 Your fax number .......................................... 20
2.10 Configuring the unit to access the LAN (KX-
MB788 only) ................................................ 21
2.11 Installing Multi-Function Station .................. 22
2.12 Starting Multi-Function Station .................... 24
3. Printer
Printer
3.1 Printing from Windows applications ............ 25
4. Scanner
Scanner
4.1 Scanning from the unit (Push Scan)............ 27
4.2 Scanning from a computer (Pull Scan)........ 29
5. Copier
Copy
5.1 Making a copy ............................................. 30
5.2 More copying features ................................. 31
6. Fax
Sending Faxes
6.1 Sending a fax manually ............................... 35
6.2 Storing items for the one-touch dial feature and
navigator directory....................................... 36
6.3 Sending a fax using one-touch dial feature and
navigator directory....................................... 37
6.4 Broadcast transmission ............................... 38
6.5 Sending a computer document as a fax
message from your computer ......................40
Receiving Faxes
6.6 Selecting the way to use your fax machine ..40
6.7 Receiving a fax automatically – Auto answer
ON................................................................41
6.8 Receiving a fax manually – Auto answer OFF
.....................................................................42
6.9 Using the unit with an answering machine...42
6.10 Receive polling (retrieving a fax placed on
another fax machine) ...................................43
6.11 Junk fax prohibitor (preventing fax reception
from undesired callers).................................43
6.12 Receiving a fax into your computer..............44
7. Caller ID
Caller ID
7.1 Caller ID service...........................................45
7.2 Viewing and calling back using caller
information ...................................................46
7.3 Editing a caller’s telephone number before
calling back/storing.......................................46
7.4 Erasing caller information.............................47
7.5 Storing caller information .............................47
8. Programmable Features
Features Summary
8.1 Programming................................................48
8.2 Basic features ..............................................49
8.3 Fax features .................................................51
8.4 Copy features...............................................54
8.5 PC print features ..........................................54
8.6 Scan features ...............................................55
8.7 LAN features (KX-MB788 only)....................56
8.8 Network features (KX-MB788, LAN connection
only) .............................................................58
9. Useful Information
Useful Information
9.1 Character entry ............................................59
9.2 Status of the unit ..........................................60
9.3 Cancelling the operations.............................60
10.Help
Error Messages
10.1 Error messages – Reports ...........................62
10.2 Error messages – Display ............................63
Troubleshooting
10.3 When a function does not work....................65
11.Paper Jams
Jams
11.1 Recording paper jam....................................73
11.2 Document jams (Auto document feeder)......78
MB778-788TW-PFQX2765ZA-OI-en.book Page 4 Tuesday, July 31, 2007 3:30 PM

Table of Contents
5
12.Cleaning
Cleaning
12.1 Cleaning the white plates and glass............ 79
12.2 Cleaning the document feeder rollers.......... 82
13.General Information
Printed Reports
13.1 Reference lists and reports ......................... 83
Specifications
13.2 Specifications .............................................. 83
Copyrights
13.3 Information of copyrights and licenses (KX-
MB788 only) ................................................ 86
14.Index
14.1 Index........................................................... 93
MB778-788TW-PFQX2765ZA-OI-en.book Page 5 Tuesday, July 31, 2007 3:30 PM

1. Introduction and Installation
6
1 Introductio n and InstallationAccess ories
1.1 Included accessories
*1 Prints about 500 A4-sized pages with a 5 % image
area (page 85).
Note:
LSave the original carton and packing materials for
future shipping and transportation of the unit.
LThe pictures and illustrations in these instructions
may vary slightly from the actual product.
1.2 Accessory information
To ensure that the unit operates properly, we
recommend using the Panasonic toner cartridge and
drum unit.
–Replacement toner cartridge*1
LModel No. (Part No.): KX-FAT92E
–Replacement drum unit*1
LModel No. (Part No.): KX-FAD93E
*1 Approx. 2,000 sheets of A4 size paper can be printed
with KX-FAT92E.
1Power cord 2CD-ROM
3Drum unit 4Starter toner
cartridge*1
5Quick reference guide 6Quick installation guide
7Telephone line cord
MB778-788TW-PFQX2765ZA-OI-en.book Page 6 Tuesday, July 31, 2007 3:30 PM

1. Introduction and Installation
7
Finding the Con trols
1.3 Button descriptions
A{COPY}
LTo switch to the copy mode (page 16, 30).
B{SCAN}
LTo switch to the scan mode (page 16, 27).
C{COLLATE}
LTo make a collated copy (page 34).
{DIRECTORY}
LTo initiate the navigator directory (page 37, 38).
D{CONTRAST}
LTo select a contrast (page 30, 35).
E{RESOLUTION}
LTo select a resolution (page 30, 35).
F{ZOOM}
LTo enlarge or reduce a document when copying
(page 31).
{QUICK SCAN}
LTo store a scanned document into memory, and
then send it (page 36).
G{PAG E LAYO U T }
LTo make quick ID, poster or N in 1 copy (page 32).
H{SET}
LTo store a setting during programming.
I{MENU}
LTo start or exit programming.
J{CALLER ID}
LTo use Caller ID features (page 46).
LTo change the display of the caller information
(page 46).
K{REDIAL}{PAUSE}
LTo redial the last number dialled. If the line is busy
when you make a phone call using the
{MONITOR}button, the unit will automatically
redial the number 1 time for phone calls and 2 or
more times for faxes.
LTo insert a pause during dialling.
L{STOP}
LTo stop an operation or programming session.
LTo erase a character/number.
M{FAX AUTO ANSWER}
LTo turn the auto answer setting ON/OFF (page
41).
N{FAX}
LTo switch to the fax mode (page 16, 35).
O{BROADCAST}
LTo send a document to multiple parties (page 38).
P{MANUAL BROAD}
LTo send a document to multiple parties manually
(page 38).
QStation keys
LTo use the one-touch dial feature (page 36, 37).
RNavigator key
LTo select desired settings during scanning or
copying (page 27, 30).
LTo adjust volume (page 19).
LTo search for a stored item (page 37).
S{LOWER}
LTo select stations 4–6 for the one-touch dial
feature (page 36, 37).
T{MONITOR}
LTo initiate dialling.
When you press {MONITOR}while receiving a
call, you will be able to hear the other party, but
the other party will not be able to hear you.
U{FLASH}
LTo access special telephone services or for
transferring extension calls.
V{TONE}
LTo change from pulse to tone temporarily during
dialling when your line has rotary/pulse service.
W{START}
LTo copy a document (page 30).
LTo scan a document (page 27).
LTo send or receive a fax (page 35).
LABCDEFG HIJK
MN QRPOSTUW
V
MB778-788TW-PFQX2765ZA-OI-en.book Page 7 Tuesday, July 31, 2007 3:30 PM

1. Introduction and Installation
8
1.4 Overview
1.4.1 Front view
1.4.2 Rear view
* The pictured model is KX-MB788.
Removing the shipping tape
Remove the shipping tape (1).
Note:
LShipping tape positions are subject to change
without notice.
1Top cover
2ADF (Auto Document Feeder) cover
3Document guides
4Document cover
5Output tray
6Top cover release lever
7Document entrance
8Paper input tray
9Recording paper exit
jDocument exit
12 43
6879j5
ARecording paper guides
BSpeaker
CPower inlet
DManual input tray (Rear cover)
EExternal telephone jack
FTelephone line jack
GUSB interface connector
HLED (KX-MB788 only)
ILAN interface connector (KX-MB788 only)
A
E G
H
F
B
I
CD
1
MB778-788TW-PFQX2765ZA-OI-en.book Page 8 Tuesday, July 31, 2007 3:30 PM

1. Introduction and Installation
9
Installation
1.5 Toner cartridge and drum unit
The included toner cartridge is a starter toner cartridge.
Caution:
LRead the following instructions before you begin
installation. After you have read them, open the
drum unit protection bag. The drum unit contains
a photosensitive drum. Exposing it to light may
damage the drum. Once you have opened the
protection bag:
– Do not expose the drum unit to light for more
than 5 minutes.
– Do not touch or scratch the black drum
surface.
– Do not place the drum unit near dust or dirt,
or in a high humidity area.
– Do not expose the drum unit to direct
sunlight.
LWe cannot be responsible for any damage to the
unit or degradation of print quality which may
occur from the use of a non-Panasonic toner
cartridge and drum unit.
LDo not leave the toner cartridge out of the
protection bag for a long time. It will decrease the
toner life.
LDo not add toner to the toner cartridge.
1Before opening the protection bag of the new toner
cartridge, shake it vertically more than 5 times.
2Remove the toner cartridge and drum unit from the
protection bags. Peel off the seal (1) from the toner
cartridge.
LDo not touch or scratch the black drum surface
(2).
3Place the toner cartridge (3) into the drum unit (4)
vertically.
4Turn the green levers (5) on each side of the toner
cartridge while pressing down firmly.
5Make sure that the triangles (6) match, to install the
toner cartridge correctly.
12
3
4
5
6
MB778-788TW-PFQX2765ZA-OI-en.book Page 9 Tuesday, July 31, 2007 3:30 PM

1. Introduction and Installation
10
6Lift the top cover release lever (7) and open the top
cover (8).
Note:
LDo not touch the transfer roller (9).
LIf the lower glass (j) is dirty, clean it with a soft
and dry cloth.
7Install the drum and toner unit (k) by holding the
tabs.
LMake sure that the triangles (l) match, to install
the drum and toner unit correctly.
8
9
7
j
k
l
MB778-788TW-PFQX2765ZA-OI-en.book Page 10 Tuesday, July 31, 2007 3:30 PM

1. Introduction and Installation
11
8Close the top cover until locked.
Caution:
LTo prevent injuries, be careful not to put your
hands under the top cover.
To replace the toner cartridge and the drum unit
When the display shows the following, replace the toner
cartridge.
TONER LOW
TONER EMPTY
LTo check the drum life and quality, please print the
printer test list (page 83) and refer to page 85 for
information on the drum life. If printing quality is still
poor or “REPLACE DRUM”appears on the display,
replace the toner cartridge and drum unit.
LTo ensure that the unit operates properly, we
recommend the use of Panasonic toner cartridge
(Model No. KX-FAT92E) and drum unit
(Model No. KX-FAD93E). See page 6 for accessory
information.
LTo maintain print quality and machine life, we
recommend you to clean slots and openings (page 3)
and the inside of the unit (page 79, 82) when
replacing the toner cartridge and/or drum unit.
Waste disposal method
Waste material should be disposed of under conditions
which meet all national and local environmental
regulations.
Toner save feature
If you want to reduce toner consumption, set the toner
save setting to ON (feature #482 on page 50). The toner
cartridge will last approximately 40 % longer. This
feature may lower the print quality.
MB778-788TW-PFQX2765ZA-OI-en.book Page 11 Tuesday, July 31, 2007 3:30 PM

1. Introduction and Installation
12
1.6 Output tray
Pull the output tray extender (1) forward gently until it
clicks into place, then press the centre part of the
extender (2) to open.
Note:
LDo not place the unit in an area where the output tray
may be easily bumped into.
LThe output tray can hold up to approximately 150
sheets of printed paper. Remove the printed paper
before the output tray becomes full.
If the top part of the extender is detached
1. With the top part of the extender in the open position,
insert the tab (1) into the left hole (2) of the
extender.
2. Slide the other tab (3) into the right hole (4) of the
extender from below until it clicks into place.
2
1
2
1
4
3
MB778-788TW-PFQX2765ZA-OI-en.book Page 12 Tuesday, July 31, 2007 3:30 PM

1. Introduction and Installation
13
If the extender is detached
1. Line up the extender (1) with the left side of the
output tray. Make sure that the triangles (2) match,
to attach the extender correctly.
2. Snap the extender (3) into the unit by pushing down
the right side of the extender.
1.7 Recording paper
The paper input tray unit can hold:
– Up to 250 sheets of 60 g/m2to 75 g/m2paper.
– Up to 230 sheets of 80 g/m2paper.
– Up to 200 sheets of 90 g/m2paper.
LPlease refer to page 84 for information on recording
paper.
LThe unit is set for printing A4 size paper by
default. If you want to use letter or legal size
paper, change the setting (feature #380 on page
50).
1Pull the paper input tray (1) until it clicks into place,
then pull it completely out, lifting the front part of the
tray.
2Before loading a stack of paper, fan the paper to
prevent paper jams.
1
2
3
1
MB778-788TW-PFQX2765ZA-OI-en.book Page 13 Tuesday, July 31, 2007 3:30 PM

1. Introduction and Installation
14
3Load the paper, print-side up (2).
Important:
LPush and lock the plate (3) in the paper input
tray, if it is lifted.
4Adjust the recording paper guides. Pinch the front
side of the recording paper guide (4), then slide it to
match the paper size mark. Pinch the right side of
the recording paper guide (5), then slide it to adjust
the width to the size of the recording paper.
LMake sure that the recording paper is under the
paper limit mark (6), and the paper should not
be loaded over the snubbers (7).
5Insert the paper input tray to the unit, lifting the front
part of the tray. Then push it completely into the unit.
Note:
LIf the paper is not loaded correctly, re-adjust the
paper guides, or the paper may jam.
LIf the paper input tray does not close, the plate in the
paper input tray may be lifted. Push the paper and
make sure that the paper is laid flat in the paper input
tray.
Caution for the paper input tray
LDo not drop the paper input tray.
LHold the paper input tray with both hands when
removing or installing. The paper input tray
weighs approximately 2 kg when the recording
paper is fully installed.
3
2
7
6
5
4
Approx. 2 kg
MB778-788TW-PFQX2765ZA-OI-en.book Page 14 Tuesday, July 31, 2007 3:30 PM

2. Preparation
15
2 Preparatio nConnecti ons and Setup
2.1 Connections
Caution:
LWhen you operate this product, the power outlet
should be near the product and easily
accessible.
LBe sure to use the telephone line cord included in
this unit.
LDo not extend the telephone line cord.
* The pictured model is KX-MB788.
Note:
LIf any other device is connected to the same
telephone line, this unit may disturb the network
condition of the device.
LIf you use the unit with a computer and your internet
provider instructs you to install a filter (5), please
connect it as follows.
* The pictured model is KX-MB788.
LA telephone handset cannot be connected directly to
this unit. To talk to the other party, please connect an
extension telephone.
1Power cord
LConnect to a power outlet
(110 V, 60 Hz).
2Telephone line cord
LConnect to a single telephone line jack.
3[EXT]jack
LYou can connect an answering machine or an
extension telephone. Remove the stopper if
attached.
4Answering machine (not included)
5Network router/Network hub (not included)*1
LAlso connect networked computers.
6To the internet*1
7LAN cable (not included)*1
LTo assure continued emission limit compliance,
use only shielded LAN cable (category 5 straight
cable).
*1 KX-MB788 only
Important notice for the USB connection
LDo NOT connect the USB cable until prompted by
the Multi-Function Station (page 22).
4
7
12
3
6
5
5
MB778-788TW-PFQX2765ZA-OI-en.book Page 15 Tuesday, July 31, 2007 3:30 PM

2. Preparation
16
2.2 Dialling mode
If you cannot dial (page 35), change this setting
according to your telephone line service.
1{MENU}i{#}{1}{2}{0}
DIALLING MODE
=TONE [V^]
2Press {1}or {2}to select the desired setting.
{1}“PULSE”: For rotary/pulse dial service.
{2}“TONE”(default): For tone dial service.
3{SET}
4Press {MENU}to exit.
2.3 Selecting the operation mode
(Scan/Copy/Fax)
You can select the desired mode by pressing one of the
following buttons.
–{SCAN}: Select this mode when using the unit as a
scanner for the computer (page 27).
–{COPY}: Select this mode when using the unit as a
copier (page 30).
–{FAX}: Select this mode when using the unit as a fax
machine (page 35).
Note:
LThe default operation mode is the copy mode.
LYou can change the default operation mode (feature
#463 on page 50) and the timer before returning to
the default operation mode (feature #464 on page
50).
{SET}
{MENU}
MB778-788TW-PFQX2765ZA-OI-en.book Page 16 Tuesday, July 31, 2007 3:30 PM

2. Preparation
17
Document R equirements
2.4 Setting the original
2.4.1 Using the scanner glass
1Open the document cover (1).
2Place the document FACE DOWN on the scanner
glass (2), aligning the top left of the document with
the corner to which the mmark points.
3Close the document cover.
Note:
LConfirm that there are no documents in the auto
document feeder.
LPlace the original onto the scanner glass gently and
do not press down too firmly to avoid malfunction.
LIf the original is a thick book, do not close the
document cover.
LCheck that ink, paste or correction fluid has dried
completely.
LEffective scanning area is as follows:
Effective scanning area
LShaded area will be scanned.
2.4.2 Using the auto document feeder
1Insert the document (up to 20 pages) FACE UP into
the feeder until a single beep is heard.
2Adjust the width of the document guides (1) to fit
the actual size of the document.
Note:
LConfirm that there are no documents on the scanner
glass.
LCheck that ink, paste or correction fluid has dried
completely.
LRemove clips, staples or other fasteners.
LDo not set the following types of documents: (Make a
copy of the document using the scanner glass and
set the copy instead.)
– Chemically treated paper such as carbon or
carbonless duplicating paper
– Electrostatically charged paper
– Badly curled, creased or torn paper
– Paper with a coated surface
– Paper with printing on the opposite side that can
be seen through the other side, such as
newsprint
LThe total height of the documents when laid flat,
must be less than 4 mm. If the documents exceed the
capacity of the auto document feeder, they may fall or
cause a jam in the feeder.
LTo set a document with a width of less than 210 mm,
we recommend using the scanner glass to copy the
original document onto A4 or letter-sized paper, then
setting the copied document.
LDo not set documents that do not satisfy the
requirements of size and weight. Make a copy of the
document using the scanner glass and set the copy.
LAvailable document size, document weight and
effective scanning area are as follows:
1
2
208 mm
287
mm
5 mm 5 mm
4 mm
4 mm
1
MB778-788TW-PFQX2765ZA-OI-en.book Page 17 Tuesday, July 31, 2007 3:30 PM

2. Preparation
18
Minimum document size
Maximum document size
Effective scanning area
LShaded area will be scanned.
Document weight
LSingle sheet:
60 g/m2to 75 g/m2
LMultiple sheets:
60 g/m2to 75 g/m2
Help
2.5 Help function
The unit contains helpful information on the following
topics which can be printed for reference purposes, as
follows:
–“BASIC SETTINGS”
–“FEATURE LIST”
–“DIRECTORY”
–“FAX RECEIVING”
–“COPIER”
–“REPORTS”
–“CALLER ID”
1Press {MENU}repeatedly to display “HELP”.
2Press {<}or {>}repeatedly to display the desired
item. i{SET}
3Press {MENU}to exit.
128 mm
128 mm
600 mm
216 mm
216 mm
208 mm
4 mm 4 mm
5 mm
5 mm
{SET}{<}{>}
{MENU}
MB778-788TW-PFQX2765ZA-OI-en.book Page 18 Tuesday, July 31, 2007 3:30 PM

2. Preparation
19
Volu me
2.6 Adjusting volume
Important:
LBefore adjusting volume, set the operation mode
to fax mode. If the {FAX}light is OFF, turn it ON
by pressing {FAX }.
Ringer volume
While the unit is idle, press {V} or {^}.
LIf there are any documents in the document
entrance, you cannot adjust the volume. Confirm that
there are no documents in the entrance.
To turn the ringer OFF
Press {V} repeatedly to display “RINGER OFF= OK?”.
i{SET}
LThe unit will not ring.
LTo turn the ringer back ON, press {^}.
Ringer pattern
LYou can select one of 3 ringer patterns (feature #161
on page 49).
Monitor volume
While using the monitor, press {V} or {^}.
Initial Programming
2.7 Date and time
1{MENU}i{#}{1}{0}{1}i{SET}
M:|01/D:01/Y:07
TIME: 00:00
2Enter the current month/date/year/hour/minute by
selecting 2 digits for each. Press {*} repeatedly to
select “AM”or “PM”, or 24-hour time entry.
Example: August 10, 2007 10:15 PM (12 hour
clock format)
1. Press {0}{8}{1}{0}{0}{7}{1}{0}{1}{5}.
M:|08/D:10/Y:07
TIME: 10:15
2. Press {*} repeatedly to select “PM”.
3{SET}
4Press {MENU}to exit.
Note:
LThe other party’s fax machine will print the date and
time on the top of each page you send according to
your unit’s date and time setting.
LAfter setting the date and time, if the unit is in the
copy mode, change it to the fax mode by pressing
{FAX}. You can check your unit’s date and time
setting on the display.
To correct a mistake
Press {<}or {>}to move the cursor to the incorrect
number, and make the correction.
{V}{^}{SET}
{FAX}
{<}{>}{SET}{FAX}
{MENU}
MB778-788TW-PFQX2765ZA-OI-en.book Page 19 Tuesday, July 31, 2007 3:30 PM

2. Preparation
20
2.8 Your logo
You can program your logo (name, company name, etc.)
so that it appears on the top of each page sent.
1{MENU}i{#}{1}{0}{2}i{SET}
LOGO=|
2Enter your logo, up to 30 characters (see page 59 for
character entry). i{SET}
3Press {MENU}to exit.
To correct a mistake
Press {<}or {>}to move the cursor to the incorrect
character, and make the correction.
LTo erase all characters, press and hold {STOP}.
2.9 Your fax number
You can program your fax number so that it appears on
the top of each page sent.
1{MENU}i{#}{1}{0}{3}i{SET}
NO.=|
2Enter your fax number, up to 20 digits.
LTo enter a “+”, press {*}.
LTo enter a space, press {#}.
LTo enter a hyphen, press {FLASH}.
LTo erase a number, press {STOP}.
3{SET}
4Press {MENU}to exit.
To correct a mistake
Press {<}or {>}to move the cursor to the incorrect
number, and make the correction.
LTo erase all numbers, press and hold {STOP}.
{<}{>}
{SET}
{MENU} {STOP}
{<}{>}
{SET} {FLASH}
{MENU} {STOP}
MB778-788TW-PFQX2765ZA-OI-en.book Page 20 Tuesday, July 31, 2007 3:30 PM