Panasonic FX-502 Series User manual

)RUPRXQWLQJDQGUHPRYLQJWKHDPSOL¿HUUHIHUWR³ MOUNTING.”
How to cascade
1. 0RXQWWKHDPSOL¿HUVRQHE\RQH
on the DIN rail.
2. 6OLGHWKHDPSOL¿HUVQH[WWRHDFK
other, and connect the quick-
connection cables.
3.
Mount the end plates MS-DIN-E
(optional) at both the ends to hold
the amplifiers between their flat
sides.
4. 7LJKWHQWKHVFUHZVWR¿[WKHHQG
plates.
+RZWR5HPRYH
1. Loosen the screws of the end
plates.
2. Remove the end plates.
3. Slide the amplifiers and remove
them one by one. Slide
Communication
window
Slide
Main cable
(Optional)
Sub cable
(Optional)
End plate
MS-DIN-E (Optional)
End plate
MS-DIN-E
(Optional)
5I/O CIRCUIT DIAGRAMS
<FX-502>
Load +
-
12 to 24V DC
%
Main circuit
(Brown) +V (Note)
(Black) Sensing output 1
(White) Sensing output 2 / External input
(Blue) 0V (Note)
<FX-502P>
Main circuit
(Brown) +V (Note)
(Blue) 0V (Note)
(Black) Sensing output 1
(White) Sensing output 2 / External input
+
-
12 to 24V DC
%
Load
Note: The quick-connection sub cable does not incorporate +V (brown) and 0V (blue). The power is supplied from
the connector of the main cable.
7HUPLQDODUUDQJHPHQW!
2
3
1
4
Terminal No. Terminal name
1+V
2 Sensing output 1
3 Sensing output 2 / External input
40V
6OPERATION PROCEDURE
ƔThe sensing output can be switched to sensing output 1 or sensing output 2
by holding down the mode key.
ƔThe changed settings are not stored if turning the power OFF while setting.
7KHUHIRUHFRQ¿UPWKH VHWWLQJV E\ SUHVVLQJ WKH 6(7NH\EHIRUHWXUQLQJWKH
power OFF.
ƔWhen turning ON the power, RUN mode is displayed and the digital display
shows the threshold value (green) and the incident light intensity (red).
• Displays threshold value (green) and incident light intensity (red).
• 7HDFKLQJWKUHVKROG YDOXH¿QH DGMXVWPHQWDQGNH\ ORFNIXQFWLRQ
can be set.
• For setting method of each function, refer to “ TEACHING
MODE,” “ THRESHOLD VALUE FINE ADJUSTMENT FUNC-
TION,” or “ KEY LOCK FUNCTION.”
<RUN mode>
• Select either Light-ON or Dark-ON.
• For the setting, refer to “SENSING OUTPUT OPERATION
MODE
.”
• The default setting is “ ” (Light-ON).
<Sensing output operation mode>
• An item set in CUSTOM mode (Response time setting, Emission
power setting and Hysteresis setting) is displayed.
• For details, refer to “ CUSTOM MODE.”
• The default setting is “ ” (response time setting).
<CUSTOM mode>
• Advanced setting can be done.
• For the setting, refer to “ PRO MODE.”
<PRO mode>
<RUN mode>
INSTRUCTION MANUAL
'LJLWDO)LEHU6HQVRU$PSOL¿HU FX-502Ƒ
MJE-FX502C No.0068-84V
Thank you very much for purchasing Panasonic products.
Please read this Instruction Manual carefully and thoroughly for the correct and
optimum use of this product.
Kindly keep this manual in a convenient place for quick reference.
WARNING
ƔNever use this product as a sensing device for personnel protection.
ƔIn case of using sensing devices for personnel protection, use products which
meet laws and standards, such as OSHA, ANSI or IEC etc., for personnel
protection applicable in each region or country.
1INTENDED PRODUCTS FOR CE MARKING
ƔThis product complies with the following standards / regulations.
(8'LUHFWLYH!
EMC Directive
<Standards in US / Canada>
ANSI/UL 60947-5-2, CAN/CSA C22.2 No.14
5HJXODWLRQVLQ.RUHD!
6*6:
ƔCaution about UL recognition
In case requiring conformity of UL listing mark or C-UL listing mark, USe class
2 power supply unit.
Ɣ&RQWDFWIRU&(
3DQDVRQLF0DUNHWLQJ(XURSH*PE+3DQDVRQLF7HVWLQJ&HQWHU
:LQVEHUJULQJ+DPEXUJ*HUPDQ\
2PART DESCRIPTION
Digital display
*UHHQ5HG
UP key
• Teaching
• Threshold value
¿QHDGMXVWPHQW
• Select setting items
MODE key
• Select Modes
• Cancel during setting
• Select sensing output 1/2
by pressing long
SET key
• Teaching
• Confirm setting
contents
DOWN key
• Teaching
• 7KUHVKROGYDOXH ¿QH
adjustment
• Select setting items
Sensing output 2
selection indicator
<HOORZ
Sensing output 1
selection indicator
<HOORZ
Sensing output 1
operation indicator
(Orange)
Sensing output 2
operation indicator
(Orange) 02'(LQGLFDWRU352<HOORZ
02'(LQGLFDWRU/'<HOORZ
02'(LQGLFDWRU&867<HOORZ
Pressing down SET key + MODE key for 3 sec : Set key lock or release key lock
3MOUNTING
How to connect
1. Fit the rear part of the mounting sec-
WLRQRIWKHDPSOL¿HURQD',1UDLO
2. Press down the rear part of the
mounting section of the unit on the
DIN rail and fit the front part of the
mounting section to the DIN rail.
+RZWRUHPRYH
1. Push the controller forward.
2. /LIWXSWKH IURQW SDUW RI WKH DPSOL¿HU
to remove it.
2. Lift up
1. Push forward
2. Press down
1. Fit
35mm width DIN rail
+RZWRFRQQHFWWKH¿EHUFDEOH
%HVXUH WR ¿W WKH DWWDFKPHQWWRWKH¿EHUV¿UVWEHIRUHLQVHUWLQJWKH¿EHUVWRWKH
DPSOL¿HU)RUGHWDLOVUHIHUWRWKHLQVWUXFWLRQPDQXDOHQFORVHGZLWKWKH¿EHUV
1. Snap the fiber lock lever down till it
stops completely.
2. ,QVHUWWKH¿EHUFDEOHVVORZO\LQWRWKH
inlets until they stops. (Note)
3. Return the fiber lock lever to the
original position till it stops.
Note: :LWKWKHFRD[LDOUHÀHFWLYHW\SH¿EHUVXFKDVFD-G4
or FD-FM2LQVHUWWKHVLQJOHFRUH¿EHUFDEOHLQWRWKH
EHDPHPLWWLQJLQOHW³3´DQGWKHPXOWLFRUH¿EHUFDEOH
into the beam-receiving inlet. If they are inserted in
reverse, the sensing performance will deteriorate.
Fiber lock lever
Fiber for
receiver
1. Snap
3. Return
2. Insert
Fiber for emitter
4
INSTALL MORE AMPLIFIER OF SERIES CONNECTION TYPE
Ɣ Make sure that the power supply is OFF while adding or removing the series connection type.
ƔIn case 2 or more the series connection types are connected in cascade, make
sure to mount them on a DIN rail.
Ɣ WKHVHULHVFRQQHFWLRQW\SHVXVLQJVXEFDEOHVFDQEHDGGHGWRDQDPSOL¿HU
using a main connection cable.
ƔWhen connecting 2 or more the series connection types in cascade, use the
sub cable (optional) for the second series connection type onwards.
<Reference>

1-point teaching [Window comparator mode (except sensing output 2) / Hysteresis mode]
ƔThis is method to set the shift amount to the desired value and to set the
threshold range by using the 1-point teaching.
<Hysteresis mode>
1_SL P-1 2_SL
<Window comparator mode>
1_SL P-1 2_SL
Set to de-
sired value
Set to de-
sired value
Set to de-
sired value
Set to de-
sired value
Stable sensing is possible
1. Pressing SET key down
2. Press the SET key down in the sensing object present condition.
Stable sensing is not possible
3. The threshold value (1_SL) that is 10% lower from the incident
light intensity and the threshold value (2_SL) that is 10% higher
from the incident light intensity are set. (Note 1, 2)
Notes 1) The shift amount of 10% is an initial value. The shift amount can be set in PRO mode. Furthermore, the shift value
can be set in incident light amount. For setting method, refer to <PRO6> in “PRO MODE OPERATION MANUAL.”
2) If the value after setting exceeds the maximum (minimum), the maximum (minimum) sensitivity will be set.
2-point teaching [Window comparator mode (except sensing output 2) / Hysteresis mode]
ƔThis is method to set the threshold range by conducting the 2-point teaching (P-1, P-2).
ƔWhen conducting teaching, use sensing objects (P-1 and P-2) whose incident
OLJKWLQWHQVLWLHVDUHGLႇHUHQWIURPHDFKRWKHU
<Hysteresis mode>
1_SL (P-1) 2_SL (P-2)
<Window comparator mode>
1_SL (P-1) 2_SL (P-2)
Stable sensing is possible
1. Pressing SET key down (1st time)
2. Press down the SET key in the sensing object present condition.
(2nd time)
Stable sensing is not possible
Note: If the value after setting exceeds the maximum (minimum), the maximum (minimum) sensitivity will be set.
3-point teaching [Window comparator mode (except sensing output 2) / Hysteresis mode]
ƔThis is the method to conduct the 3-point teaching (P-1, P-2, P-3) and to set the
threshold range by setting the threshold value (1_SL) of the mid-point between “A”
and “B” and the threshold value (2_SL) of the mid-point between “B” and “C”.
ƔWhen conducting teaching, use sensing objects (A, B and C) whose incident
OLJKWLQWHQVLWLHVDUHGLႇHUHQW
ƔAfter teaching, P-1, P-2 and P-3 will be automatically relocated in ascending order:
i.e. the lowest value is placed in “A”, the second lowest in “B” and the highest in “C”.
<Hysteresis mode>
A2_SL1_SL B C
<Window comparator mode>
A2_SL1_SL B C
Stable sensing is possible
1. Press SET key down in the sensing object present condition (1st time)
2.
Press SET key down in the sensing object present condition (2nd time)
Stable sensing is not possible
3.
Press SET key down in the sensing object present condition (3rd time)
Note: If the value after setting exceeds the maximum (minimum), the maximum (minimum) sensitivity will be set.
6SDQDGMXVWPHQWLQULVLQJGLႇHUHQWLDOPRGHRUWUDLOLQJGLႇHUHQWLDOPRGH
ƔMove to the rising differential mode, or the trailing differential mode in the
352PRGHDQG SUHVV WKH MRJ VZLWFK WR FRQ¿UP WKHVHWWLQJFor the setting
procedure, refer to <PRO6> in “PRO MODE OPERATION MANUAL.”
ƔReturn to the normal screen, press the SET key, and select Span d-01~d-08.
Then, press the SET key to complete adjustment.
Short span
Long span
Span
7TEACHING MODE
ƔBe sure that detection may become unstable depending on the use environ-
ment in teaching if less margin is applied.
ƔWhen teaching in Window comparator mode or Hysteresis mode, a setting
has to be made in PRO mode beforehand.
In case 1-point teaching, make sure to set the shift amount. (initial value is
10% or 100)
For the setting, refer to <PRO6> in “PRO MODE OPERATION MANUAL.”
ƔTeaching can be set in RUN mode.
2-point teaching This is basic teaching method.
5HÀHFWLYHW\SH!<Thru-beam type>
12
1
2
Stable sensing is possible
1.
Press the SET key in the sensing object present condition.
2.
Press the SET key in the sensing object absent condition.
Stable sensing is not possible
Limit-teaching
7KUXEHDPW\SHDQGUHIUDFWLYHW\SHDUHFRPPRQ!
or
Stable sensing is possible
1.
Press the SET key in the sensing
object present condition or non
sensing object present condition.
2.
The threshold level is shifted
to high value (low sensitivity)
by pressing down UP key.
The threshold level is shifted
to low value (high sensitivity)
by pressing down UP key.
Stable sensing is not possible
Note: The shift value of approx. 15% is an initial value. Display of the shift value can be changed to per-
centage [approx. 0 to 999% (unit 1 %)] or incident light intensity [0 to 9999 (unit 1)].
For setting the shift amount, refer to <PRO1> in “PRO MODE OPERATION MANUAL.”
)XOODXWRWHDFKLQJ
7KUXEHDPW\SHDQGUHIUDFWLYHW\SHDUHFRPPRQ!
Stable sensing is possible
1. Pressing SET key down
2. Run the sensing object on the line and hold down the
SET key.
Stable sensing is not possible
3. “ ” is displayed on the digital display (green) and
when the sensing object passed through, release the
SET key.
Automatic
Pressing down long
8VHIXOZKHQVHQVLQJREMHFWFDQEHVHW
8VHIXOZKHQVHQVLQJREMHFWFDQQRWEHVHW
This is teaching method in case small object or object in back
ground are existing.
This is method to conduct teaching doing sensing object is
moving.
8VHIXOZKHQQRWZDQWWRVWRSSURGXFWLRQOLQHDQGWRNHHSWKHVHQVLQJREMHFWPRYH

12
PRO MODE
ƔWhen MODE indicator: PRO (yellow) lights up, PRO mode can be set.
ƔFor detail of PRO mode, refer to “ PRO MODE OPERATION MANUAL.”
DOWN ( - ) key (select)
02'(LQGLFDWRU352<HOORZ
MODE key
UP (+) key (select)
6(7NH\FRQ¿UP
Procedure
<PRO1>
Shift amount setting
Timer setting
Responce time setting
Hysteresis setting
Emission power setting
Timer range setting
Teaching lock setting
Setting items in digital display setting
Setting of digital display turning
Time period hold setting
Data bank loading setting
Back up setting
Data bank saving setting
<PRO3>
<PRO2>
ECO setting
Communication protocol setting
Display adjustment setting
Setting of threshold value tracking
Copy lock setting
Copy action setting
<PRO5>
Code setting
<PRO6>
Reset setting
CUSTOM setting
Interference prevention setting
Sensing output setting
<PRO4>
Copy setting
External input setting
<PRO7>
Logic operation setting
Input / output setting
+, -
SET
SET
+, -
+, -
+, -
+, -
+, -
+, -
+, -
+, -
+, -
+, -
+, -
+, -
+, -
+, -
+, -
+, -
+, -
+, -
+, -
+, -
+, -
+, -
+, -
+, -
+, -
+, -
+, -
+, -
+, -
+, -
+, -
SET
SET
SET
SET
+, -
SET
Ɣ 7KHWKUHVKROGFDQEHVHWE\XVLQJWKHWKUHVKROGYDOXH¿QHDGMXVWPHQWIXQFWLRQ
For the threshold value fine adjustment function, refer to “ 8THRESHOLD
VALUE FINE ADJUSTMENT FUNCTION”
8THRESHOLD VALUE FINE ADJUSTMENT FUNCTION
Ɣ 6HW¿QHDGMXVWPHQWRIWKUHVKROGYDOXHLQ581PRGH
Ɣ $OVRWKHWKUHVKROG YDOXH ¿QH DGMXVWPHQW IXQFWLRQ FDQ EH XVHG LQ IRUFHG 21
output mode and forced OFF output mode.
ƔFor setting of the sensing output, refer to <PRO6> in “PRO MODE OPERA-
TION MANUAL.”
1RUPDOPRGH5LVLQJGLႇHUHQWLDOPRGHRU7UDLOLQJGLႇHUHQWLDOPRGH!
&RQ¿UPHG
Press down
UP / DOWN key
Press down
SET key
Automatically set without pressing
down SET key in approx. 2 sec.
<Window comparator mode or Hysteresis mode>
ƔWhen setting sensing output to the window comparator mode or hysteresis
mode, “ ” and “ ” can be changed to another by pressing down
SET key for 2 sec.
,QFDVHFRQGXFWLQJWKUHVKROGYDOXH¿QHDGMXVWPHQWRI³ ” or “ ”, press
down UP key or Down key, and “ ” or “ ” are displayed. Then, the
WKUHVKROGYDOXH¿QHDGMXVWPHQWFDQEHFRQGXFWHG
Press down
UP / DOWN key
Press down
SET key
Press down
UP / DOWN key
&RQ¿UPHG
Automatically set without pressing
down SET key in approx. 2 sec.
Note: It may not respond when values of “ ” and “ ” are close because of relation of hysteresis. Be sure
WRFRQ¿UPZLWKWKLVGHYLFH
9KEY LOCK FUNCTION
ƔThe key lock function prevents key operations so that the conditions set in
each setting mode are not inadvertently changed.
ƔIf operating key switch after key lock is set, “ ” is indicated on the
digital display.
6HWNH\ORFN!
Automatic
Press down for
3 sec. or more
5HOHDVHNH\ORFN!
,
are displayed
Press down for
3 sec. or more
Automatic
10
SENSING OUTPUT OPERATION MODE
ƔWhen MODE indicator: L / D (yellow) lights up, sensing output operation can be set.
Press down
SET key
Press down
UP / DOWN key
&RQ¿UPHG
&RQ¿UPHG
11
CUSTOM MODE
ƔWhen MODE indicator: CUST (yellow) lights up,
Response time setting, Emission power setting
or Hysteresis setting can be displayed.
For the setting procedure, refer to <PRO5> in
“PRO MODE OPERATION MANUAL.”
ƔBy pressing UP key or DOWN key, the setting in
each item will be changed.
MODE indicator
&867<HOORZ
UP key
SET key DOWN key
MODE key
Ɣ 3UHVV6(7NH\WRFRQ¿UPWKHVHWWLQJ
ƔFor setting of each item, refer to the following table.
Item Digital display Reference item
Response time setting <PRO 1: Response time setting>
Emission power setting <PRO 1: Emission power setting>
Hysteresis setting <PRO 1: Hysteresis setting>

15
ERROR INDICATION
ƔIn case of errors, attempt the following measures.
Error
indication Description Remedy
EEPROM is broken or reached the end of its
working life. 3OHDVHFRQWDFWRXURႈFH
EEPROM writing error
Load of the sensing output 1 is short-circuited
FDXVLQJDQRYHUFXUUHQWWRÀRZ Turn OFF the power and check the load.
Load of the sensing output 2 is short-circuited
FDXVLQJDQRYHUFXUUHQWWRÀRZ
&RPPXQLFDWLRQHUURUZKHQ WKH DPSOL¿HUVDUH
mounted in cascade.
Verify that there is no loose or clearance between
DPSOL¿HUV
Communication error between the upper com-
PXQLFDWLRQXQLWDQGDPSOL¿HUV
Verify that there is no loose or clearance between
WKHXSSHUFRPPXQLFDWLRQXQLWDQGDPSOL¿HUV
16
SPECIFICATIONS
Type Series connection type
NPN output PNP output
Model No. FX-502 FX-502P
Supply voltage 12 to 24V DC % Ripple P-P10% or less
Power consumption
(Note 1)
Normal operation: 960mW or less (current consumption 40mA or less at 24V supply voltage)
Eco mode: 680mW or less (current consumption 28mA or less at 24V supply voltage)
Sensing output
(Sensing output 1 / 2)
NPN open-collector transistor
• Maximum sink current: 50mA (Note 1)
• Applied voltage: 30V DC or less
(Between sensing output and 0V)
• Residual voltage: 2V or less (Note 2)
[At 50m A (Note 1) sink current]
PNP open-collector transistor
• Maximum source current: 50mA (Note 1)
• Applied voltage: 30V DC or less
(Between sensing output and +V )
• Residual voltage: 2V or less (Note 2)
[At 50m A (Note 1) source current]
Output operation Switchable either Light-ON or Dark-ON
Short-circuit protection Incorporated
Response time +63ȝVRUOHVV)$67ȝVRUOHVV67'ȝVRUOHVV/21*PVRUOHVV
8/*PVRUOHVV+<35PVRUOHVV6HOHFWDEOH
External input
• Signal condition
High: +8V to +V DC or Open
Low: 0 to +1.2V DC (at 0.5mA source current)
• ,QSXWLPSHGDQFH$SSUR[Nȍ
• Signal condition
High: +4V to +V DC (at 3mA sink current)
Low: 0 to +0.6V DC or Open
• ,QSXWLPSHGDQFH$SSUR[Nȍ
Protection IP40 (IEC)
Ambient temperature
-10 to +55°C (If 4 to 7 units are mounted in cascade: -10 to +50°C or if 8 to 16 units are
mounted in cascade: -10 to +45°C) (No dew condensation or icing allowed)
Storage: -20 to +70°C
Ambient humidity 35 to 85% RH, Storage: 35 to 85% RH
Material Enclosure: Polycarbonate, Key: Polyacetal, Protective cover: Polycarbonate
Weight (Main body only) Approx. 15g
Accessory FX-MB1 $PSOL¿HUSURWHFWLRQVHDOVHW
Notes:1) 50mA max. if 5 or more series connection types are connected together.
2) In case of using the quick-connection cable (cable length 5m) (optional).
3) Cables are not accessories. Be sure to use cables in table below.
<Series connection type>
Cable
Cable length 1m Cable length 2m Cable length 5m
Main cable Sub cable Main cable Sub cable Main cable Sub cable
);Ƒ CN-74-C1 CN-72-C1 CN-74-C2 CN-72-C2 CN-74-C5 CN-72-C5
17
CAUTIONS
ƔThis product has been developed / produced for industrial use only.
Ɣ 0DNHVXUHWKDWWKHSRZHUVXSSO\LV2))ZKLOHDGGLQJRUUHPRYLQJWKHDPSOL¿HUV
ƔTake care that if a voltage exceeding the rated range is applied, or if an AC
power supply is directly connected, the product may get burnt or be damaged.
ƔTake care that short-circuit of the load or wrong wiring may burn or damage
the product.
ƔDo not run the wires together with high-voltage lines or power lines, or put
them in the same raceway.This can cause malfunction due to induction.
Ɣ 7KHVSHFL¿FDWLRQPD\QRWEHVDWLV¿HGLQDVWURQJPDJQHWLF¿HOG
ƔVerify that the supply voltage variation is within the rating.
ƔIf power is supplied from a commercial switching regulator, ensure that the frame
JURXQG)*WHUPLQDORIWKHSRZHUVXSSO\LVFRQQHFWHGWRDQDFWXDOJURXQG
ƔIn case noise generating equipment (switching regulator, inverter motor, etc.)
LVXVHGLQWKHYLFLQLW\RIWKLVSURGXFWFRQQHFWWKHIUDPHJURXQG)*WHUPLQDO
of the equipment to an actual ground.
Ɣ 7KHXOWUD ORQJ GLVWDQFH 8/* +<35 PRGH LV PRUHOLNHO\WREHDႇHFWHGE\
extraneous noise since the sensitivity of that is higher than the other modes.
Make sure to check the environment before use.
Ɣ 'RQRWXVHGXULQJWKHLQLWLDOWUDQVLHQWWLPH+63)$6767'VHF/21*
8/*+<35VHFDIWHUWKHSRZHUVXSSO\LVVZLWFKHG21
ƔBe sure to using the quick connection cable (optional) as cable. When you ex-
tend the cable, be sure to use cables which have 0.3mm2or more of conductor
cross-section area. Extension up to total 100m is possible. However, in order
to reduce noise, make the wiring as short as possible.
ƔMake sure that stress by forcible bend or pulling is not applied to the sensor
FDEOHMRLQWDQG¿EHUFDEOH
ƔThis product is suitable for indoor use only.
ƔAvoid dust, dirt, and steam.
ƔTake care that the product does not come in contact with oil, grease, organic
solvents such as thinner, etc., strong acid or alkaline.
Ɣ 7KLVSURGXFWFDQQRWEHXVHGLQDQHQYLURQPHQWFRQWDLQLQJLQÀDPPDEOHRUH[-
plosive gasses.
ƔNever disassemble or modify the product.
ƔThis product adopts EEPROM. Settings cannot be done 100 thousand times
or more because of the EEPROM’s lifetime.
13
OPTICAL COMMUNICATION
ƔWhen the setting of data bank loading / saving, copy setting, or copy action
VHWWLQJLVFRQGXFWHG YLD RSWLFDO FRPPXQLFDWLRQV FDVFDGH WKH VXE DPSOL¿HUV
ULJKWVLGHWRWKHPDLQDPSOL¿HUDVIROORZV
However, in case using data bank loading / saving, use FX-502ƑRUFX-505Ƒ-C2
DVPDLQDPSOL¿HU
Ɣ ,IDQDPSOL¿HULVXQGHUDQ\RIWKHIROORZLQJFRQGLWLRQVWKHVHWWLQJRIGDWDEDQN
loading / saving, or copy setting cannot be carried out.
• Copy lock setting is set to copy lock ON “ .”
• Digital display is blinking
• ([WHUQDOLQSXWVHWWLQJRIPDLQDPSOL¿HULVVHWWR“ .” (Only data-
bank loading / saving)
ƔWhen communication protocol of a
sub amplifier is set to communication
emission halt “ ” the setting
of data bank loading / saving, or copy
setting cannot be carried out to sub
DPSOL¿HUVVXEVHTXHQWWRWKHPHQWLRQHG
DPSOL¿HU
ƔMake sure to mount closely like follows
since interference prevention function is
conducted by optical communication.
Main
DPSOL¿HU 6XEDPSOL¿HUV
Communication direction
Ɣ :KHQWKLV SURGXFW DQG RWKHU SURGXFWV HJ ¿EHUVHQVRUDPSOL¿HUVSUHVVXUH
sensor controllers, etc.) are connected together in cascade, install those prod-
XFWVVRWKDWWKH\DUHLQRUGHURI*URXS$%'DQG&DVVKRZQLQWKHULJKW¿J-
XUH7KLVSURGXFWLVLQFOXGHGLQ*URXS'
*URXS
A
*URXS
B
*URXS
D
*URXS
C
Communication direction
*URXS Model No.
AFX-301Ƒ&RQYHQWLRQDOYHUVLRQXQLW
FX-301BƑGƑHƑLS-401Ƒ
BFX-301Ƒ0RGL¿HGYHUVLRQXQLW
FX-305ƑFX-301Ƒ-C1
CLS-403ƑDPS series
DFX-500 series
Ɣ $VIRUWKHSURGXFWVWKDWDUHORFDWHGEHWZHHQGLႇHUHQWJURXSVDႈ[WKHDPSOL-
¿HUSURWHFWLRQVHDO FX-MB1 (optional) on the communication window of each
corresponding product.
ƔWithin each group, identical models should be connected in a lump.
ƔIn case conducting copy setting of this device and other FX-500 series togeth-
er, functions which are incorporated in this device will be copied but functions
which are not incorporated in this device will not be copied.
14
INTERFERENCE PREVENTION FUNCTION
Ɣ 7KLVGHYLFHLQFRUSRUDWHVDQLQWHUIHUHQFHSUHYHQWLRQIXQFWLRQE\VHWWLQJGLႇHUHQWHPLW-
ting frequencies from an interference prevention function by optical communication.
ƔFor Interference prevention function setting procedure, refer to <PRO5> in
“PRO MODE OPERATION MANUAL.”
Ɣ 3RVVLEOHQXPEHURI DPSOL¿HUV IRU LQWHUIHUHQFH SUHYHQWLRQ IXQFWLRQLVGLႇHUHQW
as shown in table below.
Response time
Interference
prevention function setting
H-SP FAST STD /21* 8/* +<35
0248812
Ɣ ,QFDVHSXWWLQJLQPRUHDPSOL¿HUVWKDQOLPLWRILQWHUIHUHQFHSUHYHQWLRQIXQFWLRQ
SXWWKHDPSOL¿HUSURWHFWLRQVHDOWRDPSOL¿HUZKLFKLVDGMDFHQWRIHQGRIDQDPSOL-
¿HUWKDWWKHLQWHUIHUHQFHIXQFWLRQLVYDOLGRUVHW2))LQFRPPXQLFDWLRQSURWRFRO
VHWWLQJRIWKHHQGRIDPSOL¿HUWKDWWKHLQWHUIHUHQFHSUHYHQWLRQIXQFWLRQLVYDOLG
([DPSOH3XWWLQJLQRIWKLVGHYLFHDQGVHW67'RIUHVSRQVHWLPHVHWWLQJ
• Possible number of interference prevention is 4.
3XWWKH DPSOL¿HU SURWHFWLRQ VHDOVWKDQGWKDPSOL¿HUVDQGEHWZHHQWK
DQGWKDPSOL¿HUVRUFKDQJHWKHFRPPXQLFDWLRQSURWRFROVHWWLQJRIWKDQG
8th to OFF since interference prevention works from 1st to 4th, from 5th to
8th and 9th to 12th.
Communication direction
Interference
prevention
possible
range
Put a protection seal between
WKDQGWKDPSOL¿HU
Or set communication protocol
setting in 4th to OFF.
Put a protection seal between
WKDQGWKDPSOL¿HU
Or set communication protocol
setting in 8th to OFF.
Interference prevention
possible range
Interference prevention
possible range
Ɣ ,QFDVHPRXQWLQJ PRUH DPSOL¿HUV ZKRVH UHVSRQVH WLPH VHWWLQJ DUH GLႇHUHQW
SXWSURWHFWLRQVHDOEHWZHHQDPSOL¿HUVWKDWKDYHGLႇHUHQWUHVSRQVHWLPHVHWWLQJ
RUVHWFRPPXQLFDWLRQSURWRFROVHWWLQJRIWKHXSSHUDPSOL¿HUWR2))
ƔFor communication protocol setting procedure, refer to <PRO4> in “PRO
MODE OPERATION MANUAL.”
Panasonic Industrial Devices SUNX Co., Ltd.
https://panasonic.net/id/pidsx/global
Please visit our website for inquiries and about our sales network.
PRINTED IN JAPAN © Panasonic Industrial Devices SUNX Co., Ltd. 2019