Panasonic AY-PB502 User manual

UC1A0
15A
PROFESSIONAL JOG PAD
ROM KIT
AY-PB502
Before attempting to connect or operate this product,
please read these instructions carefully.

This Class A digital apparatus complies with Canadian
ICES-003.
Cet appareil numérique de la classe A est conforme à la
norme NMB-003 du Canada.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
The lightning flash with arrowhead sym-
bol, within an equilateral triangle, is
intended to alert the user to the pres-
ence of uninsulated "dangerous voltage"
within the product's enclosure that may
be of sufficient magnitude to constitute a
risk of electric shock to persons.
The exclamation point within an equilat-
eral triangle is intended to alert the user
to the presence of important operating
and maintenance (servicing) instructions
in the literature accompanying the appli-
ance.
The information marking of this product may be found on the
bottom of the unit.
The serial number of this product may be found on the bot-
tom of the unit.
You should note the serial number of this unit in the space
provided and retain this book as a permanent record of your
purchase to aid identification in the event of theft.
Model No.
Serial No.
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER (OR BACK). NO USER SER-
VICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PER-
SONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
SA 1965
SA 1966
For CANADA
NOTE: This equipment has been tested and found to com-
ply with the limits for a Class A digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to pro-
vide reasonable protection against harmful interference
when the equipment is operated in a commercial environ-
ment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful
interference in which case the user will be required to cor-
rect the interference at his own expense.
For U.S.A

PREFACE
The ROM in this package is for exclusive use with the
professional jog pad in the DVEdit Operating Panel Kit
AY-RP500. Be sure to use the application software ver-
sion 2.1 or later version.
Before replacing the ROM, install the software of
Version 2.1 or higher.
Connect the professional jog pad after replacing the
ROM.
If you do not have the professional jog pad AY-JP2000,
it is not necessary to replace the ROM.
Important
• Before replacing the ROM, be sure to press the
power switch off and pull out the power plug
from the electrical outlet.
• Before handling the board, touch a metal part of
it with your hand to discharge static from your
body. Touching the board while you still have
static in your body may cause the board to fail.
It would be safer to wear an antistatic wrist
strap.
• When it is necessary to temporarily place the
board, put it on an antistatic mat or the like. Do
not let any metal part of the board contact the
metal parts of other boards.
-3-

-4-
Replacing the ROM
qQuit system operation, switch power off, and pull
out the power plug from the electrical outlet.
wRemove the case cover from the computer, then the
JOG board. Before removing it, be sure to read the
Operating Instructions for the DVEdit Operating
Panel Kit AY-RP500, and reverse the mounting
procedures.
ePlace the removed JOG board on an antistatic mat
or the like, and remove the ROM from the JOG
board.
[How to Use Remover]
Insert the hooks at the ends of the remover into the two
diagonally located holes in the ROM socket as shown in
Figure 1, and grip the remover as shown in Figure 2.
* Never forcibly pull the remover upwards.
The ROM can be removed by lifting it out of the socket.
Mark the removed ROM with red ink, for example, so it
will not be mistaken for a new ROM.
Caution: Insert the hooks at the ends
of the remover all the way in, then
pull out the ROM.
There is the danger of damaging
the ROM if the remover is not fully
inserted.
Fig. 2
Fig. 1
Hook

-5-
rPlace a new ROM in the socket. Check the direc-
tion of the mark for pin 1 so that the ROM will be
inserted in the correct direction, keep the ROM
level, apply an even force on the ROM taking care
not to bend the pins, and insert it fully till it clicks.
UC1A0
15A
Mark for pin 1
BOARD MOUNTING
tMount the JOG board according to the instructions
given in the Operating Instructions for the DVEdit
Operating Panel Kit AY-RP500.
yInsert the power plug back into the electrical outlet,
and switch power on. Check that the system is
started.

Accessories
Remover ...................................................................... 1
Warranty ...................................................................... 1
-6-

PANASONIC BROADCAST & DIGITAL SYSTEMS COMPANY
DIVISION OF MATSUSHITA ELECTRIC CORPORATION OF AMERICA
Executive Office: 3330 Cahuenga Blvd W., Los Angeles, CA 90068
[phone]
EASTERN ZONE: One Panasonic Way 4E-7, Secaucus, NJ 07094 [phone]
Mid-Atlantic: One Panasonic Way 4E-7, Secaucus, NJ 07094 [phone]
Southeast Region: 1225 Northbrook Parkway, Ste 1-160 Suwanee, GA 30024
[phone]
Central Region: 1707 N Randall Road E1-C-1, Elgin, IL 60123 [phone]
WESTERN ZONE: 3330 Cahuenga Blvd W., Los Angeles, CA 90068 [phone]
Dallas Region: 6226 Abington Way, Houston, TX 77008 [phone]
Government Marketing Department: 52 West Gude Drive, Rockville, MD 20850 [phone]
PANASONIC CANADA INC.
5770 Ambler Drive, Mississauga, Ontario, L4W 2T3 [phone]
PANASONIC SALES COMPANY
DIVISION OF MATSUSHITA ELECTRIC OF PUERTO RICO, INC.
San Gabriel Industrial Park, 65th Infantry Ave., KM9.5 Carolina, Puerto Rico 00630 [phone]
NM0499-1069 7J1A341B Printed in Japan