Panasonic CZ-ANC3 User manual

ENGLISH 2-13
Read through the Installation Instructions before you proceed with the installation.
In particular, you will need to read under the “Safety Precautions” on page 2.
FRANÇAIS 14-25
Lisez les instructions d'installation avant de commencer l'installation.
En particulier, vous devez lire la section « Consignes de sécurité » en page 14.
ESPAÑOL 26-37
Lea las Instrucciones de instalacion antes de proceder con la instalacion del equipo.
En concreto, deberá leer detenidamente la sección “Precauciones de seguridad” situada en la página 26.
DEUTSCH 38-49
Lesen Sie die Einbauanleitung, bevor Sie mit der Installation beginnen.
Insbesondere müssen die „Sicherheitsvorkehrungen“ auf Seite 38 gründlich durchgelesen werden.
ITALIANO 50-61
Leggere le Istruzioni di installazione prima di procedere con l'installazione.
Prestare particolare attenzione alla sezione “Precauzioni di Sicurezza” a pagina 50.
NEDERLANDS 62-73
Lees de installatie-instructies voordat u verder gaat met de installatie.
U moet in het bijzonder de “Veiligheidsvoorschriften” op pagina 62 lezen.
PORTUGUÊS 74-85
Leia cuidadosamente as instruções de instalação antes de prosseguir com a instalação.
Em particular, é necessário ler as informações na secção “Precauções de segurança” na página 74.
TÜRKÇE 86-97
Kuruluma başlamadan önce Kurulum Talimatlarınıbaştan sona okuyun.
Özellikle 86. sayfadaki “Güvenlik Önlemleri” kısmınıokumanız gerekecektir.
POLSKI 98-109
Przed przystąpieniem do instalacji należy przeczytaćinstrukcje instalacyjne,
a w szczególności „Środki ostrożności” na stronie 98.
РУССКИЙ 110-121
Прежде чем приступать кустановке, прочитайте инструкцию по установке.
Вчастности, следует прочитать раздел «Меры безопасности» на стр. 110.
УКРАЇНСЬКА 122-133
Перед початком установки уважно прочитайте інструкції.
Особливу увагу зверніть на розділ «Запобіжні заходи» на ст. 122.
Installation Instructions
ON/OFF Controller
Model No. CZ-ANC3
Panasonic Corporation
1006 Kadoma, Kadoma City, Osaka, Japan
85464369966010 H0517-0 CV6233339986
Panasonic Corporation
http://www.panasonic.com
ENGLISH
FRANÇAIS
ESPAÑOL
DEUTSCH
ITALIANO
N EDERLANDS
PORTUGUÊS
TÜRKÇE
POLSKI
РУССКИЙ
У КРАЇНСЬКА
業務用リモコンCZ-ANC3据付書En.indd 1業務用リモコンCZ-ANC3据付書En.indd1 2017/05/17 14:36:512017/05/1714:36:51

2(EN)
Safety Precautions
Please Read Before Starting
This controller must be installed by the sales dealer or installer.
These instructions are all you need for most installation sites and maintenance
conditions. If you require help for a special problem, contact our sales/service outlet
or your certified dealer for additional instructions.
WARNING This symbol refers to a hazard or unsafe practice which can result in
severe personal injury or death.
CAUTION This symbol refers to a hazard or unsafe practice which can result in
personal injury or product or property damage.
We assume no responsibility for accidents or damages resulting from methods
other than those described in the installation instructions or methods without using
specified parts. Malfunctions that occurred due to the unauthorised installation
methods are not covered by the product warranty.
This controller shall be installed in accordance with National Wiring Regulations.
After the installation is complete, perform test operation to confirm that no
abnormality is present.
Read the installation instructions of devices to be connected as well.
When relocating or repairing this controller, provide the Installation Instructions to the
servicing personnel.
WARNING
ELECTRICAL SHOCK CAN CAUSE SEVERE PERSONAL
INJURY OR DEATH. ONLY A QUALIFIED, EXPERIENCED
ELECTRICIAN SHOULD ATTEMPT TO WIRE THIS SYSTEM.
Highly dangerous electrical voltages are used in this system.
Carefully refer to the wiring diagram and these instructions
when wiring.
Improper connections and inadequate grounding can cause
accidental injury or death.

This controller is strongly recommended to be installed with
Earth Leakage Circuit Breaker (ELCB) or Residual Current
Device (RCD).
Otherwise, it may cause electrical shock and fire in case of
equipment breakdown or insulation breakdown.
Earth Leakage Circuit Breaker (ELCB) must be incorporated in
the fixed wiring in accordance with the wiring regulations. The
Earth Leakage Circuit Breaker (ELCB) must be an approved
10 A, having a contact separation by 3 mm in all poles.
ENGLISH
業務用リモコンCZ-ANC3据付書En.indd 2業務用リモコンCZ-ANC3据付書En.indd2 2017/05/17 14:36:512017/05/1714:36:51

3
(EN)
WARNING
 Provide a power outlet to be used exclusively for this controller.
 Turn off the circuit breaker of the controllers before installation.
Do not supply power to the controller until all wiring is
completed or reconnected and checked.
Fix the power supply wiring securely with the clamper so
that the power supply terminal board part is free of tension
(external force) when pulled. Loose connection of the
terminal board may occur fire.
To prevent possible hazards from insulation failure, the
controller must be grounded.
Select an installation location which is rigid and strong
enough to support or hold the controller, and select a location
for easy maintenance.
This product must not be modified or disassembled under
any circumstances.
Modified or disassembled controller may cause fire, electric
shock or injury.
Do not clean inside the controller by users.
Engage authorized dealer or specialist for cleaning.
Do not operate with wet hands.
CAUTION
Ground yourself to discharge static electricity before
performing any wiring.
Do not use the controller at the following locations.
•Areas where leakage of flammable gas may be expected
•Places where large amounts of oil mist exist
•Locations where external air may enter the room directly
(This may cause “condensation”.)
•Locations where high-frequency emissions are generated
•Location where voltage fluctuation frequently occurs
Do not wash with water.
NOTICE
The English text is the original instructions. Other languages are translation of the original
instructions.
ENGLISH
業務用リモコンCZ-ANC3据付書En.indd3業務用リモコンCZ-ANC3据付書En.indd3 2017/05/1714:36:512017/05/1714:36:51

4(EN)
Model No. CZ-ANC3
Dimensions (H) 120.5 mm x (W) 121.5 mm x (D) 14 + 51.1 mm
Weight 500 g
Temperature/
Humidity range
0 ˚C to 40 ˚C / 20 % to 80 % (no condensation)
*Indoor use only.
Power Source Single phase 100-240 V ~ 50/60 Hz
Power consumption Max. 4.0 W
Number of
connected indoor
units
Up to 16 groups (64 units)
Specifications
Supplied accessories
Operating Instructions (1)
Installation Instructions (1)
Switch name label (1)
Switch box
(1)
Machine Screw M4 × 25 (2)
(For Switch Box)
* Wiring are not included (field supplied item).
Safety Precautions........................... 2
Specifications................................... 4
Supplied accessories ...................... 4
Dimensions....................................... 5
Installation Precautions .................. 5
Wiring................................................ 6
Mounting......................................... 10
Switches.......................................... 11
Test Operation ................................ 12
Central Address Setting ................ 13
CONTENTS
業務用リモコンCZ-ANC3据付書En.indd 4業務用リモコンCZ-ANC3据付書En.indd4 2017/05/17 14:36:522017/05/1714:36:52

5
(EN)
Installation Precautions
Dimensions
Installation location
Avoid the following locations for installation.
• Under direct sunlight • Location near heat source • Uneven surface
• Locations where the controller will be splashed with water or affected by
dampness or humidity
• Location that is subject to excessive vibration or physical impacts. (Fixing screws
may come off, and the controller may drop.)
Install the controller away from any sources of electrical noise.
Install the controller to the locations where is suitable to the temperature for using or
environment.
When installing more than 1 controller next to each other, keep distance of 5 mm or
more on the right and left and 50 mm or more on top and bottom.
General precautions on wiring
Regulations on wire diameters differ from locality to locality. For field wiring rules,
please refer to your LOCAL ELECTRICAL CODES before beginning.
You must ensure that installation complies with all relevant rules and regulations.
Use the field supplied wiring with at least 1 mm in thickness of insulation part
including the sheath.

Connect all wiring tightly to prevent the terminal board from loosening when the wiring
connection part is pulled by an external force. (Otherwise, fire or overheating may occur.)
Do not bury the inter-unit control wiring in the ground.
Do not store the power supply wiring and other wiring in the same metal tube or
bundle them together. (An operational error or noise may occur.)
13
60
44
105
106
46
70
83.5
119
138
120.5
121.5 14 51.1
70.6
70.6
90
83.5
462.0-R2.5
mm
ON/OFF Controller
Swich box
ENGLISH
業務用リモコンCZ-ANC3据付書En.indd5業務用リモコンCZ-ANC3据付書En.indd5 2017/05/1714:36:522017/05/1714:36:52

6(EN)
Wiring
Power supply wiring
• Be sure to use a dedicated line for power source.
• Be sure to earth this controller.
• Do not connect the earth wiring to those of gas pipe, water pipe, lighting rod,
telephone, etc.
Type of wiring:
• Use a flexible wiring of 2 mm2(Recommended).
• Use the standard power supply wiring for Europe (such as H05RN-F or H07RN-F
which conform to CENELEC (HAR) rating specifications) or use the wiring based
on IEC standard (60245 IEC57, 60245 IEC66).
Total Wire Length: 30 m or less
Power supply terminal screw: M4
Inter-unit control wiring
Type of wiring:
• Use a flexible shield
wiring of 0.5 to 2 mm2.
Total wire length:
• 1000 m or less
Number of connectable units and devices:
(Up to total of 100 units and devices can be
connected.)
Indoor unit Up to 64 units (*1)
Outdoor unit Up to 30 units
Central control device Up to 10 units
(*1) The number of indoor units includes the interface
adaptor.
External I/O wiring
Type of wiring:
• Use a flexible wiring of
0.5 to 2 mm2.
Total Wire Length:
• 100 m or less
Attention
When using the controller at a location susceptible
to noise, use a shield wiring.
Before connecting wiring, be sure to turn the circuit breaker off. After all wiring
arrangements are complete, turn the circuit breaker on.
If the power supply wiring is mistakenly connected to a terminal board other than the
power supply terminal board, the devices to be connected to this controller or this
controller will malfunction. After connecting wiring, confirm that the power supply wiring
is properly connected.
業務用リモコンCZ-ANC3据付書En.indd 6業務用リモコンCZ-ANC3据付書En.indd6 2017/05/17 14:36:522017/05/1714:36:52

7
(EN)
How to attach the ring pressure terminal
For power supply wiring
• Process the end of each wiringand attach the
ring pressure terminal (field supplied item).
Strip
Ring pressure
terminal
For shield wiring
• Process the end of the each wiring and attach the ring pressure terminal
(field supplied item).
Remove wiring coat.
Cover with the tape.
Attach ring pressure
terminal.
Attention
 Ground the shield on both sides of shield wiring,
ohterwise an operation error from noise may occur.
Shield mesh
Strip
Insulation tape
Shield mesh
Basic wiring diagram
Connect the inter-unit control wiring as shown in the figure.
When connecting interface adaptor, read the installation instructions supplied with
each product.
Outdoor
unit
Indoor
unit
LN
FG

NL T1 T2 U2U1 U2U1
U2U1U2U1
Power Source
100-240V ~
Inter-unit control wiring
• No polarity
ON/OFF Controller
Schedule Timer
Ground
Ground
1-1 1-2
Outdoor
unit
Indoor
unit
Indoor
unit
Power suply
wiring
Ground Ground
Schedule Timer wiring
Power supply
terminal board
Signal terminal
board
This unit
Power
supply wiring
(white & black)
Wiring for earth
(green)
Schedule timer
100 m or less
Field supply
Communication wiring
(pink + blue)
100-240V
T1 T2
FG
FG
U1
U1 U2U2
Shield wiring
Ground Ground
ENGLISH
業務用リモコンCZ-ANC3据付書En.indd 7業務用リモコンCZ-ANC3据付書En.indd7 2017/05/17 14:36:522017/05/1714:36:52

8(EN)
Connecting wiring
Remove the 2 screws for fixing the cover, and remove the power source cover.
Connect the power supply wiring to the power supply terminal board. Be sure to
connect the earth wiring to the earth terminal.
Connect the inter-unit control wiring to the U1 and U2 terminals.

When connecting to external equipment, refer to “Connecting to external equipment” (P.9)
Attach the power source cover, and tighten the 2 screws for fixing the cover.
Screw for fixing the cover
Power source cover
The earth wiring for protection should be
longer than the power line (L, N).
Power supply wiring
L N
100-240V~
Power supply
terminal board Signal terminal board
U1 U2
Inter-unit control wiring
LINK
Use this screw when connecting
the shield for the inter-unit control
wiring to ground.(FG*)
*: Functional Ground
Note
There is no polarity for the inter-unit control wiring.
Attention
Do not run the Inter-unit control wiring through the same conduit as the power
supply, or run close to the power supply line.
Use different inter-unit control wiring and power supply wiring so they can be
differentiated visually.
Symbols on the controller
This symbol refers to “Protective earth”.
Wiring (continued)
業務用リモコンCZ-ANC3据付書En.indd8業務用リモコンCZ-ANC3据付書En.indd8 2017/05/1714:36:532017/05/1714:36:53

9
(EN)
Connecting to external equipment
Keep the signal input line lengths to 100 meters or less. For distances greater than
this, use a relay.
Condition Terminal name
Alarm output
(DO 1)
Operation output
(DO 2)
Common1
(COM 1)
Circuit example
ON/OFF controller side
Name
Input/Output
item
External equipment
side
Status
output
Control
input
Non-voltage contact “a”
Static (Relay output)
Contact allowable voltage:
Max. DC30 V
Contact allowable current:
Max. 0.5 A
Minimum application load:
DC5 V 1 mA
Contact input/output terminal
Digital input
All stop:
Voltage contact “a” Pulse
(When all stop input is ON,
the stop signal is sent
periodically.)
Pulse width:
300 msec or more
All operation:
Voltage contact “a” Pulse
Pulse width:
300 msec or more
Contact allowable voltage:
DC24 V±10 %
Contact allowable current:
Max. 10 mA
All stop input
(Di 1)
Input 1
Output
DC24 V
COM
All operation input
(Di 2)
Common 2
(COM 2)
Signal terminal board
ABC
DE
OUTPUT
INPUT 1
F
A. Common 2 (COM 2)
B. All stop input (Di 1)
C.
All operation input (Di 2)
D. Common 1 (COM 1)
E. Alarm output (DO 1)
F.
Operation output (DO 2)
ENGLISH
業務用リモコンCZ-ANC3据付書En.indd9業務用リモコンCZ-ANC3据付書En.indd9 2017/05/1714:36:532017/05/1714:36:53

10 (EN)
Mounting
When mounting the bottom case (step 2)
Tighten the screws securely until they reach the bottom case.
(Otherwise, loose screw heads may hit the PCB and cause malfunction when
mounting the top case.)
Do not over-tighten the screws.
(The bottom case may be deformed, resulting in fall of the unit.)
Embed the included switch box into the wall beforehand.
1Remove the screws for fixing the
control panel, and remove the
control panel. 3Connect the connector, and attach
the control panel.
Remove the control panel.
Control panel
Connector
Remove the connector.
Connect the connector.
2Mount to the switch box.
Insert the controller to the switch
box (supplied) that has been
embedded in the wall.
Mount the bottom case. (with the
power supply part attached) of the
controller to the switch box (with
small screws (supplied))
•
Do not allow the connection to be
exposed to the external force of wiring.
Switch Box
(supplied)
Bottom case
(with the power
supply part
attached)
ON/OFF
Controller
Wall
Switch Box
119
mm
0 - 5 mm
Cross-section view (Embedded state)
Connector
Attach it from above.
Do not allow the
wires to come in
contact with parts
on the PCB.
(Caught wires may
destroy the PCB.)
 Attach the screw
for fixing the
control panel.
Screw for fixing the control panel
業務用リモコンCZ-ANC3据付書En.indd 10業務用リモコンCZ-ANC3据付書En.indd10 2017/05/17 14:36:542017/05/1714:36:54