Panasonic WhisperSense FV-08VQC5 User manual

FV-08VQC5 FV-11VQC5
6 8
9
11
11
11
Centered/

12. Do not install with a method which is not approved in the instructions.

sa
These Panasonic ventilating fan models are equipped with a motion sensor and a humidity
sensor that turn on automatically when motion is detected, when humidity increases rapidly,
or when humidity rises above a 30% 80% relative humidity set-point. It is user-adjustable to
operate 0.5 60 minutes after the sensors are no longer detected.
~
~

Motion sensor unit
11
Humidity sensor unit
3 7/8(98)
Main control circuit
Red
Red
Yellow
Yellow
White
White
White
Black
Humidity sensor
Fan body
Red
White
Black Black
Green
Humidity setting
Motion sensor
Red
White
White
Capacitor
Motor Black
(114 C Fuse in Motor)
lmpedance-protected
Live
Neutral
( )
VENT.
Junction box
AC120V
60Hz
(Power supply)
Adjustment
switch
White
Black
Green
(Earth ground)
Timer

Humidity preset switch positions (Tolerance:±10%)
30%
~~ ~ ~ ~ ~ ~
~ ~
40% 50% 60% 70% 80%
MIN MAX
Factory setting: 50% RH (" " means "about")
Position : refer to 0.5 minute
Timer
Timer preset switch positions
Humidity
preset switch
Timer
preset switch
Motion sensor detectible
condition
Humidity sensor detectible condition
(a) rapid to moderate humidity increases and (b) humidity above a 30% 80% relative humidity
set-point. (a) and (b) are set with "HUMIDITY SETTING" adjustment. Fan may occasionally turn
on when environmental conditions change. The "TIMER" controls how long the fan remains on
(a) after rise in humidity and (b) humidity level is below the set-point decreasing about 5%RH.
Panasonic ventilating fan
responds to:
(1) Motion sensor detectible
condition.
(2) Humidity sensor detectible
condition.
2. Long-time operation will influence the detecting precision as dust accumulates. Humidity
preset switch may need to be adjusted.
1. If this unit is to be install over a tub or shower, for best results, locate it near the shower
head.
Stop
Remains running
until the delay time
has passed
The delay time is determined
by timer preset switch.
The unit continues running for
an adjustable duration
of 0.5 to 60 minutes, after
motion is no longer detected.
Human
activity
Fan activity
Room temperature is
25 (77 F).
MIN
~30%
MAX
~80%
MIN
~30%
MAX
~80%
~

Motion sensor
unit
6

Motion sensor
unit
page 4
7
A 4 or 6 inch circular duct is needed to connect to
the relevant part of adaptor. (Fig.3)
Mastic tape
4. Install a circular duct and secure it with clamps,
or wire ties and seal it with mastic or masitc tape.

9. Adjust timer preset switch and humidity preset
switch (Fig.7). Refer to switch indication on page 5.
(3 position) (Fig.6).
fix
8

9
CENTERED/
Motion sensor
unit

4. Do not use cleaning sprays, solvents, or water on
or near the sensors.
10
Remove grille by pulling down the mounting spring
opposite the sensor lead.

FV-08VQC5 15.5 815
110
960
23.0
FV-11VQC5
11
The ducting from this fan to the outside of the building has a strong effect on the air flow, noise
and energy use of the fan. Use the shortest, straightest duct routing possible for best performance,
and avoid installing the fan with smaller ducts than recommended. Insulation around the ducts can
reduce energy loss and inhibit mold growth. Fans installed with existing ducts may not achieve their
rated air flow.
1-866-292-7299(USA)

Two Riverfront Plaza, Newark, NJ 07102
T0511-2095 08VQC5420B
Panasoic Corporation 2011-2015