Panasonic WhisperSense FV-08VQCL5 User manual

Service Manual
PEG1311050CE
Version:1402
Ventilating Fan
(North America Market)
WhisperSenseTM
FV-08VQCL5
FV-11VQCL5
CONTENTS
2.Parts Identification
3.Wiring Diagram
4.Parts List
PAGE
2~4
6~7
5
WARNING
This service information is designed for experienced repair technicians only and is not designed for use by
the general public. It does not contain warnings or cautions to advise non-technical individuals of potential
dangers in attempting to service a product. Products powered by electricity should be serviced or repaired
only by experienced professional technicians. Any attempt to service or repair the product or products dealt
with in this service information by anyone else could result in serious injury or death.
IMPORTANT SAFETY NOTICE
There are special components used in this equipment which are important for safety. These parts are
marked by in the Schematic Diagrams, Exploded Views and Replacement Parts List. It is essential
that these critical parts should be replaced with manufacturer's specified parts to prevent shock, fire
or other hazards. Do not modify the original design without permission of manufacture.
We suggest to handle such parts after the static electricity prevention.
It is forbidden to touch the PCB parts by bare hands during the repairing process.
1.Specifications 1
5.Replacement Guide 8~10

1.Specifications
1
FV-08VQCL5
FV-11VQCL5

FV-08VQCL5
FV-11VQCL5
2
C
20
22
21
23
G
24
27
25
26
Grille Unit
Capacitor Box
Section
1
3
4
(3pcs)
C
(2pcs)
A
A
C
(4pcs)
C
(6pcs)
10
11
12
13
14
A
(3pcs)
Details Of Wiring Section
B
5
6
7
8
B
D
C
Cord Clip
(3pcs)
A
Capacitor Box Section
33
34
(Cord)
Black
(Motor Lead) Black
(Cord)
White
White
(Motor Lead)
Red
(Motor Lead)
White
(Motor Lead)
(4pcs)
35
Binder Tie
B
(2pcs)
Cord Clip
B
2
19 17
F
Main PCB Section
Motor Unit
32
31
29
28
H
(4pcs)
C
16
(3pcs)
E
(2pcs)
C
(2pcs)
C
18
9
30
15
2.Parts Identification

FV-08VQCL5
FV-11VQCL5
3
2.Parts Identification
Ballast Assembly Replacement Method
Total Packing Set:10sets
Ballast Assembly
Replacement
( )
59
61
60
(23)
(G)
(25)
(26)
Grille Unit
(2pcs)
Pana son ic
Packing Method
57 58
(27)
63
64
62
(2pcs)
(11pcs)
If the ballast assembly was damaged,please order the new grille unit section(FFV3420058S) to
replace defective ballast assembly&original grille unit.Please refer to P12-P14 for replacement
guide.
Remark:The minimum quantity of an order for this new grille unit is 10 sets.
(18)
56
C

FV-08VQCL5
FV-11VQCL5
Main Labels
36
37
38
41
39
40
43
mm
Inch
60 2
50
40
30
20
10
1
_
2
2
11
_
2
1
1
_
2
(Stuck On Frame Assy)
42
FAN
8B68
US
LISTEN
A375 68 2G 8 C
44
45
50
49
48
51
53
52
55
46
47
Main Packing Materials
(36)
4
54
2.Parts Identification

5
FV-08VQCL5
FV-11VQCL5
3.Wiring Diagram

No. Part No. Part Name Q'ty Remark
1
FFV1600111S Frame Assembly 1
2 FFV0420027S Bracket Cover 1
3 FFV0800001S Casing Support 3
4 FFV0000121S Adapter Assembly 1
5 FFV0900048S Connector Plate 1
6 FFV0900049S Connector Assembly V 1
7 FFV3402103S Earth Lead Wire Assembly 1
8 FFV2800012S Junction Cover 1
9 FFV0760028S Capacitor Box 1
10 FFV3702217S Motor Assembly 1 For FV-08VQCL5
(10) FFV3702215S Motor Assembly 1 For FV-11VQCL5
11 FFV3730086S Motor Support 1
12 FFV0400103S Blade 1
13 FFV7020021S Nut 1
14 FFV0790077S Casing 1
15 FFV0900039S Connector Assembly L 1
16 FFV2220053S Humid Sensor Assembly 1
17 FFV5530065S Switch Assembly 1
18 FFV3420058S Grille Unit Section 1 Include Packing Section
19 FFV3420087S Grille Unit 1 Fluorescent Lamp Brand:Maxlite
20 FFV3420025S Light Kit Cover Assembly 1
21 FFV3420026S Lamp Holder Section 1
22 FFV3420085S Fluorescent Lamp 1 Brand:Maxlite
23 FFV3420005S Night Lamp 1
24 FFV5500028S Sensor Box Assembly 1
25 FFV3420030S Grille Section 1 Include Sensor Cover&Lamp Cover
26 FFV2220051S Sensor Cover 1
27 FFV3420029S Lamp Cover 1
28 FFV3740021S Main PCB Box 1
29 FFV3740022S Main PCB 1
30 FFV4620077S Power Lead Wire 1
31 FFV3740023S Main PCB Cover 1
32 FFV3702243S Motor Unit 1 For FV-08VQCL5
(32) FFV3702244S Motor Unit 1 For FV-11VQCL5
33 FFV0750203S Capacitor 1 For FV-08VQCL5
(33) FFV0750204S Capacitor 1 For FV-11VQCL5
34 FFV0900024S Connector 4
35 FFV3700330S Motor Lead Wire 1
36 FFV4020687S Name Plate 1 For FV-08VQCL5
6
FV-08VQCL5
FV-11VQCL5
4.Parts List

7
FV-08VQCL5
FV-11VQCL5
4.Parts List
No. Part No. Part Name Q'ty Remark
(36) FFV4020688S Name Plate 1 For FV-11VQCL5
37 FFV1320001S ESP Mark 1
38 FFV0810010S Warning Label 1
39 FFV2260003S UL Mark 1
40 FFV2260002S HVI Mark 1
41 FFV6730045S Warning Label 1
42 FFV5720015S Scale Tape 1
43 FFV6730051S Wiring Label 1
44 FFV5710023S Suspension Bracket Ⅰ1
45 FFV5710024S Suspension Bracket Ⅱ1
46 FFV5710018S Suspension Bracket Ⅳ1
47 FFV5710019S Suspension Bracket Ⅲ1
48 FFV2540123S Installation Instruction 1 English,For CA Market/USA Market
49 FFV2540124S Installation Instruction 1 French,For USA Market
(49) FFV2540125S Installation Instruction 1 Spanish,For CA Market
50 FFV0010200S Accessory A 1
51 FFV4710210S Grille Case Assembly 1
52 FFV4710344S Right Pad 1
53 FFV4710345S Left Pad 1
54 FFV4710330S Sensor Pad 1
55 FFV9000985S Packing Case Assembly 1 For FV-08VQCL5
(55) FFV9000986S Packing Case Assembly 1 For FV-11VQCL5
56 FFV2540164S Installation Instruction 1
57 FFV0010230S Accessory A 1
58 FFV0730032S Cord Assembly B 1
59 FFV3420066S Light Kit Cover Assembly 1
60 FFV3420071S Lamp Holder Section 1
61 FFV3420067S Fluorescent Lamp 2
62 FFV9001067S Packing Case 1
63 FFV4710361S Pad A 2
64 FFV4710362S Pad B 11
A FFV7000065S Bind Screw 6
B FFV7000108S Truss Tap Screw 5
C FFV7000089S Truss Tap Screw 20
D FFV7000168S Screw Assembly 1 Include Spring Washer&P.R Washer
E FFV7000195S Pan Tap Screw 2
F FFV7000074S Truss Tap Screw 1
G FFV7000191S Bind Screw 1 For Fixing Light Kit Cover Assembly
H FFV7000145S Truss Tap Screw 4

8
5.Replacement Guide
INSTALLATION
3. Fix the switch box by 1 screw (ST4.2X8) from
accessories. (Fig.3)
2. Take off the ballast assembly by removing 3 screws
(ST4.2X12). (Fig.2)
4. Take out the light lead wire assembly A from
accessories, and connect to junction box. Then
fix the light lead wire assembly by 3 screws (ST4.2X12),
and 3 cord clips(5N,from accessories).(Fig.4)
1. Remove the primary light kit grille by pulling down
one mounting spring, and remove
plug connectorⅠ,then pull down the other mounting
spring (Squeeze mounting spring and pull down
carefully) (Fig.1)
remove sensor unit
.
Keep the screws that are removed for
following use.
Ceiling
Grille
sensor unit
Gloves
Rib
Claw
Ballast Assembly
Switch box
Switch box
Lighting unit
Plug connector
Mounting spring
Fig.4
Fig.5
For models of FV-08VKML3,
FV-13VKML3 only. Only fix
the sensor lead wire.
Fig.1
Light lead wire assembly A
Screw(ST4.2X8)
3 screws(ST4.2X12) Fig.2
Fig.3
3 screws(ST4.2X12),3 cord clips(5N)
Disconnect power source before working
on unit.
WARNING
Remove the tapes from grille and springs
before installation new light kit grille as below
5.Take out the new light kit grille.Remove screw(M4X8).
Remove light kit cover assembly. (Fig.5)
CAUTION
Tapes
IMPORTANT:
Light kit cover
assembly
Remove screw
(M4X8)

9
5.Replacement Guide
INSTALLATION
10. Insert the other mounting spring into the slot as
shown and mount grille to fan body. (Fig.10)
9. Insert the sensor unit into slot of the grille
(position ① . Fix the sensor lead wire into the
clasp (position ② (Fig.9)
)
).
Fig.8
Fig.10
Fig.9
8. Insert the grille mounting spring on the wiring
side into the slot and insert the plug connector
into the housing of the lighting unit.(Fig.8)
Mount grille carefully so that lead wire of
sensor unit and lighting unit is not pinched.
Before turn on the light, make sure the
connector at the correct position. If not, the
lighting can’t work.
The claw of connector must latch the rib
completely. (Fig.8)
Ceiling
Grille
Grille
Grille
Ceiling
Clasp
Sensor unit
Gloves
Gloves
Rib
Claw
Insert
lighting unit
lighting unit
Plug connector
Plug connector
Mounting spring
Mounting spring
6. Install the night lamp and fluorescent lamps.
(Fig.6)
7. Install light kit cover assembly. (Fig.7)
3Fig.6
Fig.7
Secure screw
(M4X8)
CAUTION
CAUTION
Fluorescent
lamp
Night lamp
Light kit cover
assembly

MAINTENANCE(REPLACEMENT OF LAMP)
4. Install new night lamp (MAX 4W incandescent lamp) and
new fluorescent lamps (Maxlite MLS13GU35,13W) as
shown in step 1 ,step 2 and step 3 of (Fig.4)
WARNING
Remove dust and dirt from light kit cover
assembly and lens, before replace the lamps.
CAUTION
3. Remove the fluorescent lamps (Maxlite MLS13GU35,13W)
and night lamp as shown in step 1 ,step 2 and step 3 of (Fig.3)
2. Remove the screw as shown in step 1 of (Fig.2)
Remove the light kit cover assembly as shown in step 2 of (Fig.2)
1. Remove grille by pulling down one mounting spring. Then
pull down the other mounting spring. (Squeeze mounting
spring and pull down carefully) (Fig.1)
5.Install light kit cover assembly.(Fig.5)
Disconnect power source before working
on unit.
Make sure the temperature of lens and lighting
unit has cooled down before maintenance
(cleaning) or replacement of lamp.
This is a pin type lamp base and the lamp’s
glass is fragile.To remove,pull out carefully.
4W night lamp has threaded base,Remove
by turning counterclockwise.
Fig.2
Fig.3
3
Lens
3
Fig.4
Fig.5
Secure screw
(M4X8)
Fluorescent
lamp
Night lamp
Light kit cover
assembly
Fluorescent
lamp
Night lamp
Light kit cover
assembly
Remove screw
(M4X8)
Plug connector
lighting unit
Insert Plug connector
Rib
Claw Fig.1
Gloves
Ceiling
Grille
5.Replacement Guide
10