Panasonic EH-ND12 User manual

© Panasonic Electric Works (Thailand) Co., Ltd.
2011. All rights reserved. Unauthorized copying and
distribution is a violation of law.
Order Number PEWT1107A23CE
Hair Dryer
Model No. EH-ND12
EH-ND13
INDONESIA
TABLE OF CONTENTS PAGE PAGE
1 Warning-------------------------------------------------------------- 2
2 Specifications ----------------------------------------------------- 2
3 Troubleshooting Guide----------------------------------------- 3
4 Disassembly and Assembly Instructions ---------------- 4
5 Wiring Connection Diagram ---------------------------------- 9
6 Schematic Diagram---------------------------------------------10
7 Exploded View and Replacement Parts List -----------11

2
1Warning
Caution:
• Pb free solder has a higher melting point that standard solder; Typicall the melting point is 50 - 70°F (30 - 40°C) higher. Please
use a soldering iron with temperature control and adjust it to 750 ± 20°F (400 ± 10°C). In case of using high temperature solder-
ing iron, please be careful not to heat too long.
• Pb free solder will tend to splash when heated too high (about 1100°F / 600°C).
2 Specifications

3
3 Troubleshooting Guide
Refer to WIRING CONNECTION DIAGRAM.

4
4 Disassembly and Assembly Instructions
4.1. Disassembly instruction
1. Remove 1 torque screw from Housing B by using torque head driver as shown in Figure 1.
2. Remove 3 hooks of Housing B from Housing A by using flared tip screw driver as shown in Figure 2.
3. Remove the Motor B/K, Heater B/K, and Main switch.

5
4.2. Assembly instruction
CAUTION: When soldering lead wires on the main switch, location and orientation of lead wires must be as shown in Fig-
ure 3.
1. Assemble Heater B/K into slots of Motor B/K as shown in Figure 4.
2. Solder lead wire White and lead wire Violet into Heater B/K as shown in Figure 5.

6
3. Insert the Lead wires between the guide post of Air flow regulator, and align Heater insulator slot and lead wires as shown in
Figure 6.
4. Put Air flow ass'y B/K into Housing B and aligning all lead wires as shown in Figure 7.

7
5. Set Air outlet Grill to Housing A by aligning slot of Air outlet grill and Housing A as shown in Figure 8.
6. Assemble Air inlet grill into Housing B by aligning mark of Air inlet grill and mark of Housing B as shown in Figure 9.
7. Install Main switch plate and Main switch lever with Housing A, then assembly Housing A and Housing B as shown in Figure
10.

8
8. Fasten 1 torque screw as shown in Figure 11.

9
5 Wiring Connection Diagram

10
6 Schematic Diagram

Model No. : EH-ND12 Exploded View for EH-ND12
7 Exploded View and Replacement Parts List

Model No. : EH-ND12 Parts List
Safety
Ref.
No. Part No. Part Name & Description Q'ty Remarks
EH-ND12
1 EHND12SNZPW SET NOZZLE 1
2 EHND12HSAPW HOUSING A 1
3 EHND12AOGW AIR OUTLET GRILL 1
4 EHND12MH4B2W MOTOR HEATER BLOCK 1 B2-PLUG,INDONESIA
5 EHND12HSBP4W HOUSING B 1
6 EHND12AIGPW AIR INLET GRILL 1
7 EHND12MSPPW MAIN SWITCH PLATE 1
8 EHND12MSLHW MAIN SWITCH LEVER 1
9 EHND12MSW MAIN SWITCH 1
10 EHND12T0312W TORX SCREW 3.0*12 1
- EHND1241503W OPERATING INSTRUCTIONS 1
- EHND1241501W INDIVIDUAL PACKAGE 1

Model No. : EH-ND13 Exploded View for EH-ND13

Model No. : EH-ND13 Parts List
Safety
Ref.
No. Part No. Part Name & Description Q'ty Remarks
EH-ND13
1 EHND13SNZVW SET NOZZLE 1
2 EHND13HSAVW HOUSING A 1
3 EHND13AOGW AIR OUTLET GRILL 1
4 EHND13MH4B2W MOTOR HEATER BLOCK 1 B2-PLUG,INDONESIA
5 EHND13HSBV4W HOUSING B 1
6 EHND13AIGVW AIR INLET GRILL 1
7 EHND13MSPVW MAIN SWITCH PLATE 1
8 EHND13MSLHW MAIN SWITCH LEVER 1
9 EHND13MSW MAIN SWITCH 1
10 EHND13T0312W TORX SCREW 3.0*12 1
11 EHND13NZVW NOZZLE AB BLOCK 1
- EHND1341503W OPERATING INSTRUCTIONS 1
- EHND1341501W INDIVIDUAL PACKAGE 1