Panasonic VL-SWD501AZ User manual

Wireless Video Intercom System
Key Features
• Wireless Handset: Check visitors on Wireless Monitor, respond promptly and talk from living room, kitchen, everywhere home and while you are doing something
else. UP to 6 wireless monitor connectable. Max wireless range is 100m with no obstacles. You can add on repeaters expand the range. UP to 2 DECT repeater connectable.
• Large Touch Panel: The main monitor has a large, 5 inch wide screen that clearly shows each visitor's face. You can simply touch the screen to activate an
approximate 2x zoom horizontally and vertically.
• Electric Lock Release Support for Gate: The gate or door lock can be easily and quickly released even from the second oor of the house.
• Wide-Angle Camera: Wide-angle lens covers approximately 170 degrees horizontally and 115 degrees vertically.
• SD Card Recording: Automatically record video images of visitors to SD card. It will record up to 3,000 visitors (30 seconds per visitor).
(The SD Memory Card is sold separately.)
• Wireless Sensor Cameras: By installing the optional DECT Wireless Sensor Camera, you can use human (heat) and motion sensors to monitor locations
that you are concerned about. UP to 4 wireless sensor camera connectable.
• Night Vision: Door Station is equipped with LED lights (illumination lamp). It enables the colour display of visitors at a distance of about 50 cm at night.
For the Sub Monitor: AC adaptor × 1 (PNLV226AL), Rechargeable batteries × 2, Charger × 1
For the Door Station: <VL-V554BX> Mounting base × 1 & screw (3.8 mm x 20 mm) × 2, Screw (4 mm x 12 mm) × 4, Name plate × 2, Hex wrench × 1
<VL-V554UBX> Flush mounting box × 1, Screw (4 mm x 25 mm) × 4, Name plate × 2, Hex wrench × 1
For the Main Monitor Station: Power supply unit* (VL-PS241) × 1, Mounting bracket × 1, Cable binder × 1, Screw (4 mm x 16 mm) × 2
*Including AC cable × 1, Cable binder × 1, Screw (4 mm x 40 mm) × 2
Wiring Schematic Diagram
Accessory Information
Optional Accessories
POWER SUPPLY UNIT
DOORPHONE 1
MAIN MONITOR
DOORPHONE 2
220-240 V AC
Connection device for option output (A contact)
NP: Non-polarised
12 V AC/DC
12 V AC/DC
Electric lock
Electric lock
24 V DC
A
B
D
C
C
NP NP
NP
NP
NP
NP
Power
supply
Power
supply
Wire type and length
Wiring run Wire type*1
Diameter Length (Max.)
Main monitor – Doorphone
φ 0.65 mm 22 AWG 100 m
φ 1.0 mm 18 AWG 130 m
φ 0.5 mm CAT 5 50 m
Main monitor – Power supply unit φ 0.65 mm 22 AWG 10 m
φ 1.0 mm 18 AWG 20 m
Doorphone – Electric lock*2φ 0.5 mm - φ 1.2 mm (24 AWG - 17 AWG) According to specication of connected device.
Main monitor – Connection device for
option output (A contact)*2φ 0.5 mm - φ 1.2 mm (24 AWG - 17 AWG) According to specication of connected device.
Wireless sensor camera –
Power supply unit –φ 0.65 mm 22 AWG 50 m
φ 1.0 mm 18 AWG 100 m
Wireless sensor camera –
External sensor –φ 0.5 mm - φ 0.8mm (24 AWG - 20 AWG) According to specication of connected device. Must be no longer than 20 m.
*1 Type: Single-pair cable with outer sheath (jacket) Conductor: Copper
solid
• A certied power supply wiring has to be used with this equipment.
The relevant national installation and/or equipment regulations shall
be considered. A certied power supply wiring not lighter than ordinary
polyvinyl chloride exible wiring according to IEC 60227 shall be used.
*2 When using an electric lock or a connection device for option output (A
contact), select a device that meets the following guidelines:
• Electric lock connection terminal (S1/S2):
- N/O dry closure contact
- 12 V AC/DC, less than 1 A
• Connection device for option output (A contact) terminal (OUT1/OUT2):
- 24 V AC/DC, less than 0.3 A (minimum contact: 5 V DC 1 mA)
VL-SWD501AZ/UAZ
B
A
C
D
Door Station
(Doorphone)
VL-V554BX
VL-V554UBX
DECT Repeater
VL-FKD2AZ
Wireless
Monitor Station
(Sub monitor)
VL-WD613AZ
Wireless Sensor Camera
VL-WD812AZ
Door Station
(Doorphone)
VL-V522LBX
Optional
Wireless Camera

Specications
Model Composition
Installing the Main Monitor
Installing the Doorphone
Installing the Wireless Camera
VL-MWD501BX VL-V554BX (Surface mount)
VL-V554UBX (Flush mount) VL-WD613BX VL-PS241
Model number and name Main Monitor Station (Main monitor) Door Station (Doorphone) Wireless Monitor Station (Sub monitor) Power Supply Unit (part)
Main body Charger
Dimensions
Power source Power supply unit (VL-PS241)
24 V DC, 0.5 A
Power supplied by the main monitor
20 V DC, 0.23 A Rechargeable Ni-MH (AAA x 2)
AC adaptor (PNLV226AL)
Input: 220-240 V AC, 0.1 A, 50/60 Hz
Output: 5.5 V DC, 0.5 A
Input: 220-240 V AC, 0.2 A, 50/60 Hz
Output: 24 V DC, 0.6 A
Power consumption Standby: Approx. 1.4 W
During operation: Approx. 10 W - -
Standby: Approx. 0.4 W (when the sub
monitor is not placed in the charger)
During charging: Approx. 1.4 W
-
Dimensions (H x W x D)
(Excluding protruding sections) 180 x 165 x 21 mm
VL-V554BX: 169 x 118 x 30 mm
VL-V554UBX: 169 x 118 x 16.5 mm
(excluding sections embedded into the wall)
173 x 52 x 30 mm 43 x 81 x 76 mm 104 × 100 × 54 mm
Weight 470 g VL-V554BX: 405 g, VL-V554UBX: 345 g 160 g (including the batteries) 70 g (excluding the AC adaptor) 215 g
Operating environment 0 °C to 40 °C, Up to 90 % RH
(Relative Humidity) non condensing
-10 °C to 50 °C, Up to 90 % RH
(Relative Humidity) non condensing
0 °C to 40 °C, Up to 90 % RH
(Relative Humidity) non condensing
0 °C to 40 °C, Up to 90 % RH
(Relative Humidity) non condensing
0 °C to 40 °C, Up to 90 % RH
(Relative Humidity) non condensing
Display Approx. 5 inch, wide colour display - Approx. 2.2 inch, colour display - -
Frequency 1.88 GHz to 1.90 GHz - 1.88 GHz to 1.90 GHz - -
Option output (A contact)
Rated load: 24 V AC/DC, 0.3 A or lower
Minimum applicable load: 5 V DC, 0.001 A
(Output when there is a call from the doorphone)
----
Viewing angle -Horizontally: Approx. 170°
Vertically: Approx. 115° ---
Installation method Wall mount
(mounting bracket supplied)
VL-V554BX: surface mount
(mounting base supplied)
VL-V554UBX: ush mount
(ush mounting box supplied)
---
IP rating / IK rating - IP54*3 / Compliant with IK07 - - -
External material Flame retardant ABS and PS resin Aluminium and ame retardant PC+PS resin ABS resin ABS resin Flame retardant PC+ABS resin
VL-WD812AZ VL-FKD2AZ
Model number and name Wireless Sensor Camera DECT Repeater
Dimensions
Power source Power supply unit (VL-PS241)
24 V DC, 0.4 A
AC adaptor (PQLV219AL)
Input: 220-240 V AC, 0.1 A, 50/60 Hz
Output: 6.5 V DC, 0.5 A
Power consumption
During standby: Approx. 1.5 W
During operation: Approx. 4.5 W (when
the LED lights are not lit), Approx. 8 W
(when the LED lights are lit)
During standby: Approx. 1.5 W
During operation: Approx. 2.3 W
(when transmitting)
Dimensions (H x W x D)
160 x 118 x 290 mm
(when the camera is front facing and
including the wall mount bracket)
82 x 111 x 39 mm
Weight 960 g 88 g (excluding the AC adaptor)
Operating environment
-20 °C to 50 °C,
Up to 90 % RH (Relative Humidity)
non condensing
0 °C to 40 °C
Up to 90 % RH (Relative Humidity)
non condensing
Frequency 1.88 GHz to 1.90 GHz 1.88 GHz to 1.90 GHz
Installation method Wall mount
(wall mount bracket supplied) -
Transmitting range Approx. 100 m (line-of-sight distance
from the main monitor)
Approx. 100 m (line-of-sight distance
from the main monitor)
Minimum illuminance required 1 lx*1-
Image sensor 0.3 M pixel CMOS -
Lighting method 2 white LED lights*2-
Angular eld of view
(camera angle)
Horizontal: Approx. 53°
Vertical: Approx. 41° -
Sensor detection range
• Heat sensor (when the surrounding
temperature is approx. 20°)
Horizontal: Approx. 63°, vertical: Approx.
20°, detection range: Approx. 5 m
• Motion detection sensor Horizontal:
Approx. 53°, vertical: Approx. 41°
-
Sensor detection method Pyroelectric infrared sensor
(heat sensor) and motion detection -
IP rating IP54*3-
Adjustable mounting angles
Horizontal: ±90°, vertical: facing forward
- facing down approx. 60°
(adjustable when mounting)
-
Heat sensor adjustable angles Manually adjustable to 2 angles -
External material PC+ABS resin PS resin
VL-SWD501AZ VL-MWD501BX x 1, VL-WD613BX x 1, VL-V554BX x 1
VL-SWD501UAZ VL-MWD501BX x 1, VL-WD613BX x 1, VL-V554UBX x 1
Attach the mounting bracket to the wall securely.
Install the mounting bracket on a vertical at wall.
MG-DHPL003EN 1410ITP/ZZZ-AZ1
Important
– Safety Precaution: carefully read the operating instructions and installation manual before using this product.
• The actual product may vary slightly from photograph.
• Weights and dimensions are approximate.
• Design and Specifications are subject to change without notice.
• These products may be subject to export control regulations.
*1 The minimum illuminance required when the camera’s [Brightness] setting is set to [+3].
*2 Approx. 8.5 lx when 3 m in front of the camera, and approx. 4 lx when 3 m away and 20° to the left or right of the camera.
*3 Water resistance is only assured if the camera is installed correctly according to the instructions in the Installation Guide, and
appropriate water protection measures are taken. Do not install the camera in areas directly exposed to water or rain.
Vertical, at wall
Screws
Hole in wall
83.5 mm
60 mm
7 mm
50 mm
Mounting bracket
Mounting base
(accessory)
Wire (locally procured)
Wall
83.5 mm
Screw × 2
Install the mounting base on a vertical at wall.
• VL-V554BX (Surface mount)
Mounting screws
(locally procured) × 4 46 mm
83.5 mm
Cable access hole
DC cable
Screws (accessory)
Flush mounting box
(accessory)
• VL-V554UBX (Flush mount)
100 mm
151 mm
37 mm
165 mm 21 mm
180 mm
118 mm
Up to 2 Up to 6
30 mm
16.5 mm
35.8 mm
169 mm
52 mm 30 mm
173 mm
81 mm 76 mm
43 mm
100 mm
104 mm
*Indoor use only.
118 mm
142 mm 94 mm
290 mm
160 mm
111 mm 39 mm
82 mm
Up to 4 Up to 2