Panasonic VL-SV74 User manual

Model No.
Installation Guide
Model Name Model No.
VL-SV74
Video Intercom System
Main Monitor Station
RThis guide is for use with the above 3 models.
Door station Main monitor station
RThe Installation Guide in Indonesian and Thai can be accessed from the following site:
https://panasonic.net/cns/pcc/support/intercom/sv74
RDoor station is described as "doorphone" and Main monitor station is described as "main
monitor" in this guide.
RIn this guide, the suffix of each model number (e.g., the "BX" in "VL-SV74BX") is omitted
unless necessary.
Note to the installer
RBefore attempting to connect or operate this product, please read the label on the rear of
the doorphone and the main monitor/extension monitor.
RPlease read this guide carefully, and install the product safely and correctly by following
the instructions. Carefully read the information found in the section titled "For your
safety" in particular.
ROnly use attachments/accessories specified by the manufacturer.
RThe installation shall be carried out in accordance with all applicable installation rules.
RTo the maximum extent permitted by law, Panasonic assumes no responsibility for
injuries or property damage resulting from failures arising out of improper installation
or operation inconsistent with this document.
RAfter installation, make sure to leave this guide with the customer.
VL-MV74
Door Station VL-V524
RThe VL-SV74 models composition consists of VL-MV74 and VL-V524.
VL-V524 VL-MV74
prj_6905-en_gb.book Page 1 Friday, March 8, 2019 2:29 PM

2
For your safety
To prevent severe injury or loss of life or
property, and to ensure proper and safe
operation of your product, read this
section carefully before using the
product.
Preventing fire, electric shock and
short circuits
RLeave installation work to the
dealer. Installation work requires
technique and experiences. Failure
to observe this may cause fire,
electric shock, injury, or damage to
the product. Consult the dealer.
RElectrical connection work should
be performed by certified personnel
only. Certification is required for
performing electrical connection
work. Consult your dealer.
RDo not attempt to disassemble or
modify this product. Contact an
authorised service centre for repairs.
RNever install wiring during a lightning
storm.
RDo not connect non-specified devices.
RDo not connect a power cable to a
terminal that is not specified in this
guide.
RWhen opening holes in walls for
installation or wiring, or when securing
the power cable, make sure you do not
damage existing wiring and ductwork.
RDo not make any wiring connections
when the power supply is turned on.
RDo not install the main monitor/
extension monitor in the following
places:
– Places where the main monitor/
extension monitor may be splashed
with water or chemicals.
– Places where there is a high
concentration of dust, or high
humidity.
RDo not place objects on the power
cables.
Install the product where no one can
step or trip on the power cables.
RDo not allow the power cables to be
excessively pulled, bent or placed
under heavy objects.
RWhen existing wires are used, it is
possible that they contain AC voltage.
Contact an authorised service centre.
Preventing electric shock
RIf the wiring is underground, do not
make any connections underground.
RIf the wiring is underground, use a
protection tube.
RIf the wiring is outdoors, use a
protection tube or a surge protector.
Preventing injury
RInstall the product securely adhering to
the instructions in this guide to prevent
it from falling off the wall. Avoid
installing onto low-strength walls, such
as gypsum board, ALC (autoclaved
lightweight concrete), concrete block,
or veneer (less than 18 mm thick)
walls.
WARNING
CAUTION
prj_6905-en_gb.book Page 2 Friday, March 8, 2019 2:29 PM

3
Supplied accessories for installation
Important:
RYou will need the following additional items to install and configure the doorphone and the
main monitor/extension monitor.
Note:
RThe illustrations in the supplied manual(s) may vary slightly from the actual product.
*1 Used when using a separately sold flush mount box for installation.
For the doorphone
Mounting base ×1
Screw ×2
(3.8 mm ×20 mm)
Screw ×4
(4 mm ×12 mm)
Screw ×4
(4 mm ×25 mm)*1
For the main monitor/extension monitor
Screw ×2
(4 mm ×16 mm)
Mounting bracket ×1
[Locally procured]
– Wires (for doorphone and other connections):
Prepare wires of the appropriate specification. (a"Wire type and length")
prj_6905-en_gb.book Page 3 Friday, March 8, 2019 2:29 PM

4
Precautions for installation
To avoid malfunction or communication disturbances, do not install the doorphone or the main monitor/
extension monitor in the following locations:
– Places where vibration or any other kind of impact occurs.
– Places where echoing is frequent.
– Places near a high concentration of dust, hydrogen sulphide, ammonia, sulphur, or noxious fumes.
For the doorphone
RIf a strong light is shining on the doorphone, the visitor’s face may not be distinguishable. Do not place
the doorphone in the following locations:
– Where most of the background is the sky.
– Where the background is a white wall, and direct sunlight will reflect off it.
– Where direct sunlight will shine on the doorphone.
RDo not place the doorphone in locations where echoing occurs, as this will cause the doorphone to
beep frequently.
RDust protection/water protection is IP44.
Only when installation work specified in this guide is properly performed and appropriate water
protection treatment is performed.
RMake sure the rear of the doorphone is not subject to water.
RDepending on the installation location, condensation may form on the doorphone’s lens cover. This
may cause images to become obscured. Condensation will dissipate as the temperature rises.
For the main monitor/extension monitor
RLeave at least 20 cm of space above, below, and to the left and right sides of the main monitor/
extension monitor. Do not install on a wall that is deeply recessed.
RDo not install the main monitor/extension monitor inside a wall.
RBe sure to install the main monitor/extension monitor more than 5 m away from the doorphone.
RIn areas surrounded by a high electrical field, disturbances may occur in the main monitor’s/extension
monitor’s image or sound.
Important:
RDo not use any cleaning products that contain alcohol, polish powder, powder soap, benzine, thinner,
wax, petroleum, or boiling water. Also do not spray the product with insecticide, glass cleaner, hair
spray or wall paint. This may cause a change in colour or quality of the product.
prj_6905-en_gb.book Page 4 Friday, March 8, 2019 2:29 PM

5
Wiring schematic diagram
Set up correctly according to the following wiring schematic diagram and "Wire type and length".
RFor information, such as order numbers, about optional devices that can be connected to, refer to the
"Additional/replacement accessories" section in the Operating Instructions.
APower supply
*1 When you use an additional doorphone, the maximum number of the electric locks that can be
connected to the doorphone depends on the type of doorphone. Consult your dealer for further
information.
For VL-V554 users:
– The electric lock can also be connected to the S1/S2 terminals of the doorphone.
*2 Connection devices for option input (A contact).
– Make sure to connect doorbells to the IN3/IN4 terminals. A doorbell and doorphone 2 cannot be
used together.
– When a VL-V901 and VL-V700 series Video Intercom System for Apartment Complexes is used,
emergency terminals can be used. Make sure to connect emergency terminals to the IN1/IN2
terminals.
Ml-1
Ml-2
5
6
Ml-1
Ml-2
5
6
Ml-1
Ml-2
5
6
EXTENSION
MONITOR 1
EXTENSION
MONITOR 2
EXTENSION
MONITOR 3
DOORPHONE 1 DOORPHONE 2
Electric
lock
Electric
lock NP: Non-polarised
MAIN MONITOR
D1
D2
D3
D4
Ml-1
Ml-2
IN1
IN2
IN3
IN4
P1
P2
MO-1
MO-2
MO-3
MO-4
MO-5
MO-6
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
S1
S2
S3
S4
19
20
21
22
Connection device
for option Input
(A contact) *2 PBX
AA
NP
NP
NP
NP
NP
NP
NP
NP
NP
NP
Terminal box
(4-conductor
wiring)
You can also connect an
optional lobby station. (See
page 7.)
Power plug
(220-240 V AC)
*1 *1
prj_6905-en_gb.book Page 5 Friday, March 8, 2019 2:29 PM

6
Wire type and length
*1 Type: Single-pair cable with outer sheath (jacket)
Conductor: Copper solid
RA certified power supply wiring has to be used with this equipment. The relevant national
installation and/or equipment regulations shall be considered. A certified power supply wiring not
lighter than ordinary polyvinyl chloride flexible wiring according to IEC 60227 shall be used.
*2 When an extension monitor is used, make sure that the total wiring length from the doorphone to the
main monitor and then to the extension monitor, is within about 100 m.
*3 When using an electric lock or a connection device for option input (A contact), select a device that
meets the following guidelines:
RElectric lock connection terminal (S1/S2, S3/S4):
– N/O dry closure contact
– 30 V AC (1 A)/24 V DC (1 A) or lower
RConnection device for option input (A contact) terminal (IN1/IN2/IN3/IN4):
– Input method: No-voltage contact
– Open-circuit voltage between terminals: DC 7 V or less
– Detection definite time: 0.1 second or more
– Short-circuit between terminals: 5 mA or less
– Resistance value: make: 500 Ωor less, break: 15 KΩor more
Wiring run
Wire type*1
Diameter Length (Max.)
Doorphone –
Main monitor –
Extension monitor*2
ø 0.65 mm 22 AWG 100 m
ø 1.0 mm 18 AWG 130 m
ø0.5mm CAT5 50m
Main monitor –
Electric lock*3
ø 0.5 mm - ø 1.2 mm
(24 AWG - 17 AWG)
According to the
specifications of the
connected device.
Main monitor –
Connection device for
option input (A contact)*3
ø 0.5 mm - ø 1.2 mm
(24 AWG - 17 AWG)
According to the
specifications of the
connected device.
Main monitor –
PBX ø 0.65 mm CAT 3 or 22 AWG 100 m
prj_6905-en_gb.book Page 6 Friday, March 8, 2019 2:29 PM

7
Connecting an optional lobby station
For information about connections, refer to the documentation of the lobby station to be connected.
<Be sure to perform the following to ensure proper operation>
RConnecting an optional VL-V591 lobby station
– Connect terminal D1/D2 on the main monitor with terminal D1/D2 on the lobby station.
– Connect terminal S1/S2 on the main monitor with terminal S1/S2 on the lobby station.
– After connecting to the main monitor, change the [Lobby connection] setting to [Device connected]
using the main monitor. (→Operating Instructions of the Video Intercom System.)
Note:
RConnection for VL-V901 and VL-V700 series Video Intercom System for Apartment Complexes
– Connect terminal D1/D2 on the main monitor with terminal D1/D2 on the VL-V701 Distribution Box.
RConnection for VL-VM series/VL-VM701 Video Intercom System - Lobby station/Distributor
– Connect either terminal D1/D2 or D3/D4 on the main monitor with the terminal on the Lobby station
or VL-VM701 Distributor.
MAIN MONITOR
D1
D2
D3
D4
Ml-1
Ml-2
IN1
IN2
IN3
IN4
P1
P2
MO-1
MO-2
MO-3
MO-4
MO-5
MO-6
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
S1
S2
S3
S4
19
20
21
22
<Rear view>
Example: VL-V591 Lobby station
NP
NP: Non-polarised
NP
prj_6905-en_gb.book Page 7 Friday, March 8, 2019 2:29 PM

8
Doorphone installation position
Installation position of the doorphone and camera range
Views when the camera is facing forwards at 0° (default).
RExample: Installation height is 1450 mm (standard position).
(Units: mm)
AImage range BApprox. 54° CCentre of doorphone DApprox. 1450 EApprox. 500
FApprox. 1740 GApprox. 510 HApprox. 1230 IImage range: Approx. 920 JApprox. 85°
KApprox. 500
AImage range BApprox. 54° CCentre of doorphone DApprox. 1100 EApprox. 500
FApprox. 1590 GApprox. 560 HApprox. 1030 IImage range: Approx. 1050 JApprox. 260
KApprox. 790 LApprox. 85° MApprox. 500
*1 If the camera points 15° upwards, the left or right angle is less than 5°.
Note:
RThe measurements and angles are for reference purposes and may vary depending on the
environment.
A
C
D
E
G
H
I
J
K
A view when looking
from above
B
F
The camera angle can be adjusted using the camera angle control lever on the rear of the
doorphone (step 3, “Installing the doorphone”), so that the image range can be changed.
Side view when the camera is installed
lower than the standard position, and
facing upwards at 15°.
Top view when the camera is facing left or
right at 15° *1.
RExample: Installation height is 1100 mm.
(Units: mm)
RExample: Camera angle faces left 15°.
A
B
C
D
E
F
G
H
I
JK
LM
prj_6905-en_gb.book Page 8 Friday, March 8, 2019 2:29 PM

9
Installing the doorphone
Important:
ROn the bottom surface of the doorphone and the
mounting base, there are holes to allow water to
drain. Do not cover them up when installing.
RWhen existing wiring (such as chime wires) is
used:
– It may contain AC voltage that may cause
electric shock and/or damage the product.
– Never use the following types of wiring.
Consult a qualified technician/dealer.
RSee "Wire type and length" for information about
wiring materials.
1Attach the mounting base (B) (accessory) to
the wall securely.
RInstall the mounting base on a vertical flat
wall.
AScrews (accessory) ×2
CWire (locally procured)
D83.5 mm
*1 To prevent dew condensation, fill a hole for
wiring as much as possible.
2Use a slotted screwdriver (A) to push into the
holes on the bottom side of the front panel, and
remove the front panel (B) of the doorphone.
3Adjust the camera angle using the camera
angle control lever.
ACamera angle control lever
BLeft (maximum 15°)
CRight (maximum 15°)
DUpwards (maximum 15°)
B
D
*1
A
C
When using flush mount box (option):
Model No. VL-MB524
Install the flush mount box (A) in the
wall.
BKnockout hole*1
CApprox. 90 mm DApprox. 138 mm E
Approx. 37 mm
*1 Only open the knockout holes as
required for the wiring.
AC
D
E
B
B
A
Rear view
A
BC
D
prj_6905-en_gb.book Page 9 Friday, March 8, 2019 2:29 PM

10
Examples of camera angle
RThe angle can also be adjusted to the right
or upper right.
Important:
RWhen the camera angle is adjusted to the
upper left or upper right, the image may be
slightly distorted.
4Connect the wires.
Loosen the screws. Push in the wires to the
terminal connectors (non-polar), then tighten
the screws (A).
5Attach the doorphone to the mounting base.
AScrews (accessory) ×4
6Attach the front panel in the order of A→B.
A– Recommended torque: 0.5 N·m
{5.1 kgf·cm}
– Maximum torque: 0.7 N·m {7.1
kgf·cm}
Facing upper leftFacing left
Facing forwards Facing upwards
1
When using flush mount box (option):
Model No. VL-MB524
Attach the doorphone to the flush mount
box.
AScrews (accessory) ×4
A
A
A
B
prj_6905-en_gb.book Page 10 Friday, March 8, 2019 2:29 PM