Panasonic EP3202-U1 User manual

©2004 Matsushita Electric Works, Ltd. All rights
reserved. Unauthorized copying and distribution is a
violation of law.
EP3203/EP3202-U1
MASSAGE LOUNGER
SPECIFICATIONS
ORDER NO.HPD0401U11C1
E11

1 COMPONENTS IDENTIFICATION 3
2 MASSAGE RANGE (MOVEMENT RANGE OF MASSAGE
WHEELS) SHIATSU MASSAGE, SWEDISH MASSAGE,
KNEADING, VIBRATING, TAPPING A, TAPPING B, TAPPING
C, WHOLE BACK ROLLING, REGIONAL ROLLING 5
3 TURNING ON THE POWER 6
4 REQUIRED TOOLS 7
5 ACTUAL WIRING DIAGRAM 8
6 DISPLAY METHOD OF MASSAGE BLOCK TOTAL USE TIME
AND OPERATION TIME 9
7 MOTION OF THE CLUTCH AND BELT BASED ON VARIOUS
MASSAGER OPERATIONS 10
8 CONTROL OF THE AIR-MASSAGE OPERATION 12
9 MASSAGER UP/DOWN SENSOR GEAR ADJUSTMENT
METHOD 13
10 DISASSEMBLY AND ASSEMBLY INSTRUCTION 14
11 ACTUAL WIRING DIAGRAM 50
12 CHECKING 52
13 GREASE 59
14 EXPLODED VIEW 61
15 REPLACEMENT PARTS LIST 68
CONTENTS
Page Page
2
EP3203-U1

1 COMPONENTS IDENTIFICATION
1.1. Massage lounger
3
EP3203-U1

1.2. Controller
4
EP3203-U1

Width adjustment
Approx.50 to 210 mm (2.4in. to 8.3in.)
Intensity adjustment
Shiatsu, Swedish, Knead, vibration, Tap A, Tap B, Tap C,
whole back roll, and Regional roll (from gentle to strong)
:50mm(2.4in.)-wide adjustability where massage heads
push out toward body as intensity increases.
2 MASSAGE RANGE (MOVEMENT RANGE OF MASSAGE
WHEELS) SHIATSU MASSAGE, SWEDISH MASSAGE,
KNEADING, VIBRATING, TAPPING A, TAPPING B,
TAPPING C, WHOLE BACK ROLLING, REGIONAL
ROLLING
5
EP3203-U1

3 TURNING ON THE POWER
1.Plug the power plug into the power socket.
2.Turn the lock switch to the open position.
3.Turn on the power switch on the back of the unit.
· When the operating lock switch is pointing toward ´lock´, the power switch cannot be moved to the ´on´ position.
After each use.
·Be sure to turn the power switch to ´off´.
·To prevent children from using this unit, lock the power switch by moving the operating
lock switch to the ´lock´ position.
·As a further caution, unplug the power cord from the power socket after each use.
Timer
When the on/off button is pushed, a timer begins to prevent overuse. After approximately 15 minutes, time expires and the
massage wheel goes into storage position.
6
EP3203-U1

4 REQUIRED TOOLS
7
EP3203-U1

5 ACTUAL WIRING DIAGRAM
5.1. Connecting cord for power source to Sub PCB
8
EP3203-U1

6 DISPLAY METHOD OF MASSAGE BLOCK TOTAL USE
TIME AND OPERATION TIME
Adjustment of pressure sensor
First, keep the Massage mechanism block unloaded with pressure and move it upward halfway.
If the Massage mechanism block is at the highest or lowest position, you cannot arrange the pressure sensor correctly because
the fabric becomes tense with pressure.
1.While pushing On/off button and the User program button B simultaneously, turn on the power switch and continue to hold the
buttons for approximately 5 seconds. Release after the Focus button lights up.
2.Push the Focus button and automatically it lights off.
Turn off the Power source switch and turn it on again, then the adjustment is finished.
Total use time & Display method
While pushing the Shiatsu button and the Deep button simultaneously, turn on the power switch and continue to hold the
buttons for approximately 5 seconds. Release after the User program button A.
e.g. In the above case, 3000 + 500 + 10 + 5 = 3515 hours.
It is possible to indicate up to 5,995 hours.
If the use time is less than 5 hours, 5 hour unit does not light up. If it is less than 10 hours, one 5 hour unit lights up.
9
EP3203-U1

Chart for reading each function use time
7 MOTION OF THE CLUTCH AND BELT BASED ON
VARIOUS MASSAGER OPERATIONS
Massager operation and belt motion
10
EP3203-U1