Panasonic KX-HTS Series User manual

Please read this leaflet carefully when you install KX-HTS series and KX-HDV
series to the existing user network.


Step 1: Program KX-HTS series
1. Connect KX-HTS series to the existing User Network, and then connect the PC to the KX-HTS series as the figure.
2. In Web Maintenance Console, configure the following settings for KX-HTS series
PC
Internet
Existing User Network
KX-HTS series
Existing Router
PC KX-HDV series
(e.g., KX-HDV230)
For your information, Video Instruction about the installation is uploaded on the Panasonic Web site at:
https://channel.panasonic.com/contents/19893/

KX-HTS series
Existing User Network
(192.168.22.0/24)
LAN1: 192.168. 0.101/24
WAN1: 192.168.22. 99/24
To PC
To Existing Router
(192.168.22.1/24)
PC
(Enable DHCP)
Existing Router
Internet
b. Disable the Firewall setting
c. Set the network address of the existing user network to enable
communication with KX-HDV series connected in the existing user network
Network Configuration > 7.Firewall > 1.Firewall
a. Set the IP address, Subnet Mask, and Default Gateway for the
WAN1 port
Note
Configure the settings according to the IP address system of the
existing user network. Also, set the IP address which does not
duplicate other IP device.
PBX Configuration > 2.Extension > 7.SIP Extension Property
Network Configuration > 3.WAN > 1.WAN Setting

Step 2: Connect KX-HDV series to KX-HTS series
Step 3: Change the Network settings of KX-HDV series
For connecting the KX-HDV series (e.g., KX-HDV230) to the existing user network, configure the following settings:

Step 4: Connect KX-HDV series to the existing user network
Repeat Steps 2 to 4 for the number of KX-HDV series to be registered.
KX-HTS series
KX-HDV series
(e.g., KX-HDV230)

Dec.3112:45PM
101
Note
If the extension number is not displayed on the LCD of KX-HDV series
for more than 10 minutes after connecting the KX-HDV series to the
KX-HTS series, initialize the KX-HDV series. Refer to the Web site at:
http://www.panasonic.net/pcc/support/pbx/manual/kx-hts/index.html
2. KX-HDV series will be registered to KX-HTS series
automatically. Confirm that an extension number (e.g., 101) is
displayed on the LCD of KX-HDV series.
1. Connect the “LAN” port of KX-HDV series to the "LAN”
port of KX-HTS series.
e.g., K-HDV230:
Back view
LAN
p
ort
1. Press Menu 2. [▲]/[▼]: “System Settings” →OK 3. [▲]/[▼]: “Network Settings”→OK
IPv4 Settings
DHCP
Static
4. [▲]/[▼]: “IPv4 Settings” →OK
IP Address
192.168. 22. 151
6. Enter the IP address
*1
→Next
Subnet Mask
255.255.255. 0
Default Gateway
192.168. 22. 99
Error:003
Not Registered
7. Enter the subnet mask →Next 8. Enter the default gateway
*2
→OK
“Not Registered” will be displayed.

Dec.3112:45PM
101
Status
Network Settings
System Settings
Status
Network Settings
System Settings
IP Mode Select
IPv4 Settings
IPv6 Settings
5. [▲]/[▼]: “Static” →OK
*1 Enter the IP address according to the IP address system of the existing user network. Also, please set the IP
address which does not duplicate other IP device.
*2 For the default gateway setting, enter the IP address of the WAN1 port of KX-HTS series which is the same
value as “IP Address, by your ISP” shown as below. DO NOT set the IP address of the existing router.
Network Configuration > 3.WAN > 1.WAN Setting
KX-HTS series
Existing Router
KX-HDV series
(e.g., KX-HDV230)

Dec.3112:45PM
101
e.g., K-HDV230:
1. Disconnect the KX-HDV series from the LAN port of KX-HTS
series, and connect to the existing router.
2. KX-HDV series will be registered to KX-HTS series
automatically. An extension number is displayed on
the LCD of KX-HDV series.
PNQW5376ZA-VB PP0117TN0