Panasonic SH-ALL1C User manual

SQT0184-4
until
2014/03/24
Owner’s Manual
<Full version>
Network Audio Connector
Model No. SH-ALL1C
Thank you for purchasing this product.
Please read these instructions carefully before using this product,
and save this manual for future use.
Register online at www.panasonic.com/register (U.S. customers only)

- 2 -
Table of contents
Accessories........................................................................................ 3
Unit care............................................................................................. 4
Control reference guide...................................................................... 5
Indicator illumination .......................................................................... 6
Connections ....................................................................................... 8
Network settings............................................................................... 12
Enjoying music ................................................................................. 19
Firmware updates ............................................................................ 23
Others .............................................................................................. 24
Troubleshooting................................................................................ 27
Specifications ................................................................................... 30
How to use this manual
Click/Tap this icon to jump to “Table of contents”.
≥Pages to be referred to are indicated as “l±±”. You can jump to the
corresponding page by clicking/tapping this.

- 3 -
Accessories

≥Do not use AC power supply cord (AC mains lead) with other equipment.
≥Product numbers provided in this owner’s manual are correct as of May 2014.
These may be subject to change.
1 AC power supply cord (AC mains lead)
(K2CB2CB00022)
(K2CT2YY00097)
(K2CQ2YY00119)
(K2CJ2YY00101)
1 Audio cable
(K2KYYYY00242)
2 Stands
(RYQ1443-K1)
For the United Kingdom and Ireland
For Continental Europe
For Australia and New Zealand

- 4 -
Unit care
Clean this unit with a soft, dry cloth.
≥Never use alcohol, paint thinner or benzine to clean this unit.
≥Before using chemically treated cloth, carefully read the cloth’s instructions.
∫To dispose or transfer this unit
The unit may keep the user settings information in the unit. If you discard
this unit either by disposal or transfer, then follow the procedure to return
all the settings to the factory defaults to delete the user settings.
(l27, “To return all settings to the factory defaults”)
≥The operation history may be recorded in the memory of this unit.
Disposal of Old Equipment
Only for European Union and countries with recycling
systems
This symbol on the products, packaging, and/or
accompanying documents means that used electrical and
electronic products must not be mixed with general household
waste.
For proper treatment, recovery and recycling of old products,
please take them to applicable collection points in accordance
with your national legislation.
By disposing of them correctly, you will help to save valuable
resources and prevent any potential negative effects on
human health and the environment.
For more information about collection and recycling, please
contact your local municipality.
Penalties may be applicable for incorrect disposal of this
waste, in accordance with national legislation.

- 5 -
Control reference guide
1Mode switch [MODE]
Set the downsampling setting (l24)/
Turn the beep sound on/off (l25)
2WPS pairing switch [-WPS]
Enter WPS pairing mode (l16) / firmware update mode (l23)
3Standby/on switch [Í/I]
Touch to switch the unit from on to standby mode or vice versa. In standby
mode, the unit is still consuming a small amount of power.
4Mode indicator (amber)
5Network indicator (blue/red)
6Operation indicator (amber)
–WPS MODE
13
4
2
56
: Touch area

- 6 -
Indicator illumination
The indicator patterns illustrated below are displayed during normal
operational conditions.
Indicator Description
Operation indicator (amber) Blinks once
≥The unit detects the switch touched.
Blinks twice
≥The unit detects a valid operation
performed by touching and holding
the switch.
Mode indicator (amber) Blinks once
≥The following setting is turned on.
“Downsampling” (l24)
“Operation sound setting” (l25)
– When the setting is turned off, it blinks
twice.
Blinks
≥It may blink when the unit turns to
standby mode.
– Do not disconnect the AC power
supply cord (AC mains lead). Doing
so may cause malfunction or
damage.

≥The mode indicator also blinks when
the volume is changed on the app.
(l19)
–WPS
MODE
–WPS
MODE

- 7 -
Indicator Description
Network indicator (blue/red) Blinks alternately
≥The unit is carrying out an internal
process.
– Wait for maximum of approximately
60 seconds before the blinking stops.
– Do not disconnect the AC power
supply cord (AC mains lead). Doing
so may cause malfunction or
damage.
Network indicator (blue) Blinks slowly
≥The unit is ready for network setup.
(l12)
Blinks
≥The unit is waiting for the WPS
connection. (l16)
Blinks fast
≥The unit is waiting for the WPS PIN
code connection. (l16)
Network indicator (blue) Lights up
≥The unit is connected to the
network.
Network indicator (red) Blinks
≥The unit is connecting to the
network.
– When the network connection cannot
be established, the blinking keeps
going. Check the network connection.
(l12)
–WPS
MODE
–WPS
MODE
–WPS
MODE
–WPS
MODE
–WPS
MODE

- 8 -
Connections
You can enjoy music from a device on the network by using this unit.
At first, you must connect an audio system, amplifier or receiver, etc. to
this unit.
This unit can be installed either vertically or horizontally.
∫Horizontal
Install the unit with the rubber feet side down as shown below.
STEP1: Installation
Ex. Connecting to an audio system
Rubber feet

- 9 -
∫Vertical
Place the stands and fit the unit into them.
Install the unit with the AllPlay
icon side up.
Stands (supplied)
Rubber feet
When placing the stands, align
them with the rubber feet.
Stands (supplied)

- 10 -
Connect an audio system, amplifier or receiver, etc. to this unit using an
audio cable (supplied) or an optical cable (not supplied).
∫Using an audio cable (supplied)
∫Using an optical cable (not supplied)

≥For details, refer to the operating instructions of the connected device.
STEP2: Connecting to an audio system, etc.
AUDIO OUT
RL
RL
AUDIO IN AUDIO OUT L
R
Audio cable (supplied)
Optical cable (not supplied)