
Operating Instructions
(Household use) Nose/Ear/Facial Trimmer Head
Model No. ER-CNT1
ER-CNT1
Safety precautions
Follow these instructions.
To prevent accidents, injuries or damage to property, please follow the
instructions below.
The following chart indicates the degree of damage caused by
improper operation.
Indicates potential hazard that could result in serious
injury or death.
Indicates potential hazard that could result in minor
injury or property damage.
WARNING
Preventing accidents
• Do not place within reach of children or infants. Do not let them
use it.
-Putting parts or accessories in the mouth may cause an accident or
injury.
CAUTION
Protecting the skin
•
• Do not press the blade with excessive force or insert too deeply
• Do not touch the blade section (metallic section) of the inner blade.
• Do not use this appliance for any purpose other than to trim nose
hair, ear hair, outline eyebrows, moustache or beard.
-Doing so may cause injury to skin or hand.
• Check the blades are not damaged or deformed before use.
-Failure to do so may cause injury to the skin.
Note the following precautions
• Do not share with your family or other people.
-
Important information
• Note the following precautions to avoid malfunction or deformation.
• Do not bring the blade into contact with hard objects.
• Do not drop or hit against other objects.
• Be sure to place the protective cap on the head when carrying around or
storing.
Parts identification (Fig. 1)
AHead
1Protective cap
2Outer blade
3Inner blade
4Trimmings box
5Water inlet
6Water outlet
7Wash switch ring
8Filter
9Exhaust hole
Before use (Fig. 2)
Be sure to close the water inlet of the wash switch ring during use.
” align.
How to use
• Clean the appliance after use.
1 Mount the head to the main body until it clicks.
2 Remove the protective cap and hold the main body so as not to block
the exhaust hole (a). (Fig. 3)
3 Turn on the power before putting the head in your nostril.
Cut hairs using the tip of the outer blade (metallic part).
The outer blade surface may get a little warm during use,
but performance will not be diminished.
Note
• The use time after a full charge is as follows.
ER-CBL1: Approximately 80 minutes
ER-CBN1: Approximately 60 minutes
(Based on dry using at 20 °C - 30 °C [68 °F - 86 °F])
The operating time may differ depending on the frequency of use and the
operating method.
Quick charge (ER-CBL1 only)
Even though the battery runs out, you can use for 5 minutes after
3-minute charge.
(This will differ depending on usage.)
Removing and mounting the head (Fig. 4)
• Make sure that the main body is turned off.
Remove
Remove the head while pushing the head release button (b).
Stand the head when it is removed.
Mount
Mount the head to the main body until it clicks.
Trimming your nose hair and ear hair (Fig. 5)
1 Insert the tip of the outer blade into your nostril or ear canal.
Insert it slowly so as not to injure your nostril or ear canal.
2 Cut the nose hair and ear hair by moving the main body.
Some trimmings may remain inside your nostril or ear canal after cutting,
so remove them using a tissue or similar.
Outlining your eyebrows, moustache, or beard
(Fig. 6)
1 Apply the tip of the outer blade to the hair (eyebrow, moustache or
beard) you would like to cut.
2 Cut the hair by moving the appliance slowly against the direction of
hair growth.
You cannot trim the hair to length with this head.
It is not suitable for the hair below 0.5 mm (1/64").
English
•
-
•
•
•
•
-
•
-
•
-
•
•
•
•
(
A
1
2
3
4
5
6
7
8
9
(
."
•
(a
•
:ER-CBL1
:ER-CBN1
E R- CBL1
(
•
.(b
(
(
.("/
ER9210CNT12221_EN-AR.indd 1
ER9210CNT12221_EN-AR.indd 1
31/3/2566 BE 16:59