Panasonic WJHD309 - DIGITAL DISK RECORDER Instruction Manual

Digital Disk Recorder
WJ-HD300 series S-ATA conversion guide
WJ-HD309, WJ-HD316,WJ-HD309A,WJ-HD316A
1. Sept. 2008
Panasonic System Solutions

1
Panasonic System Solutions HD300_SATAConversionGuide_B
WJ-HD300 S-ATA conversion guide Maintenance guide
1. Introduction
This manual describes how to convert the hard disk drive installed in the WJ-HD300 series from the P-ATA type to the S-ATA type.
Applicable models: WJ-HD309, WJ-HD316, WJ-HD309A, WJ-HD316A
2. Preparation
(1) Screwdriver
(2) S-ATA conversion kit (part number: 0E0A0027AA)
Part name Part number Quantity
S-ATA Board Ass’y JH30AJKY6A 1
S-ATA cable K1V322Y20001 1
S-ATA angle 3CA005877AAA 1
S-ATA label, small (for front, 2pcs) 3PD003840AAA 1
S-ATA label, large (for top) 3PD003841AAA 1
S-ATA leaet 3TU001942AAA 1
(3) S-ATA HDD (250GB) x 2 (part number: HDATW250GASY)
3. Replacement Procedure
Important +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
• Do not detach the cable connecting the unit and the front panel while the HDD status indicators are still lit or until 30 seconds have passed
since the HDD status indicators went off.
• Protect the hard disk drives from static electricity.
• Do not stack them, or keep them upright.
• Do not use an electric screwdriver to x them. (Tightening torque: Approx. 0.49 N · m (5 kgf · cm))
• Avoid rapid changes in the temperature/humidity to prevent condensation. (Acceptable change: within 15°C/h (59 °F/h))
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
(1) Open the connectors cover on the front panel, and remove
the screw.
Then, remove the front panel by sliding it to the left.
Screw
Connectors cover

2
Panasonic System Solutions HD300_SATAConversionGuide_B
WJ-HD300 S-ATA conversion guide Maintenance guide
(2) Disconnect the connector from the front panel.
(3) Remove four screws that x the HDD mounting unit, and
then pull the HDD unit toward you by holding the tabs of
the angle.
(4) Remove four screws xing the upper HDD.
Disconnect the IDE connector and power connector from
the HDD, and remove the HDD from the HDD mounting
angle.
Caution++++++++++++++++++++++++++++++++++++
When removing the screws, hold the HDD by hand to prevent
it from falling and being impacted.
+++++++++++++++++++++++++++++++++++++++++++
Front panel
connector
SSD
SSD
Screws
Hold these
tabs and pull
SSD
Pull-ring
Jumper pin
Screws for the upper
hard disk drive
(4 screws: 2 screws each
on the both sides)
Hard disk drive mounting angle
Flat cable
Power supply
cable

3
Panasonic System Solutions HD300_SATAConversionGuide_B
WJ-HD300 S-ATA conversion guide Maintenance guide
(5) To remove the lower HDD, disconnect the power
connector from the ATA board.
Then, remove the screw A; one of the three screws xing
the ATA board.
(6) Remove four screws xing the lower HDD.
Disconnect the connectors from the HDD, and remove the
HDD from the HDD mounting angle.
Caution++++++++++++++++++++++++++++++++++++
When removing the screws, hold the HDD by hand to prevent
it from falling and being impacted.
+++++++++++++++++++++++++++++++++++++++++++
(7) Disconnect the IDE cable from the ATA board.
(8) Remove the two other screws xing the ATA board, and
then remove the ATA board.
(9) Remove two screws xing the ATA angle, and then
remove the ATA angle.
(10) Install new S-ATA angle on the HDD mounting angle with
the two screws removed in step (9).
SSD
Hard disk drive mounting angle
Screws for the lower hard disk drive
(4 screws: 2 screws each
on the both sides)
Screw removed from
point A
Connector of the
power supply cable
Screw removed from point A
Screw A
Screw A
ATA Board
ATA board screws
(2 screws)
Angle screws
HDD mounting angle

4
Panasonic System Solutions HD300_SATAConversionGuide_B
WJ-HD300 S-ATA conversion guide Maintenance guide
(11) Install the S-ATA board on the S-ATA angle with the three
screws removed in step (5) and step(8).
(12) Install two S-ATA HDDs in the HDD mounting angle with
four screws each.
Note: No jumper is provided on the S-ATA HDD.
Install the HDD so that the board side faces down and the
connector side faces the S-ATA board.
(13) Connect the S-ATA cables and the power cable to the
S-ATA board and the HDDs as shown right. Make sure
that the connectors have been inserted completely.
HDD mounting angle
SATA board
screws (3screws)
SATA board
Screw A
Twist the power supply
cable 360° and insert
For HDD2 (Gray)
For HDD1 (Red)
CN301
CN302
For power supply
CN305
To prevent the
cables from
banking, pass the
gray cable under
the red cable.

5
Panasonic System Solutions HD300_SATAConversionGuide_B
WJ-HD300 S-ATA conversion guide Maintenance guide
(14) Install the HDD mounting unit with the four screws removed in step (3) in the reverse order of removal.
Caution ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
•When installing the HDD mounting unit, remove dust around the connector that connects the HDD mounting unit the and the main unit.
Adhesion of dust may cause a trouble.
•Insert the connectors and screws rmly.
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
(15) Attach the S-ATA label, small (for front) to the front
chassis.
(16) Connect the connector to the front panel, and install the
front panel with the screw remove in step (1) and close the
connectors cover.
Approx.
3mm
Approx. 3mm
SATA label(for front)
Confirm that the power supply
cable and the HDD cable do
not touch the front chassis.

6
Panasonic System Solutions HD300_SATAConversionGuide_B
WJ-HD300 S-ATA conversion guide Maintenance guide
(17) Attach the S-ATA label, large (for top) to the top panel.
Attach the S-ATA label, small (for front) to the connectors
cover.
Note:
The new HDDs need to be formatted before operation. Refer to the Operating Instructions for detail.
+++++++++++++++++++++++++++++++++++++End of the document+++++++++++++++++++++++++++++++++
PAN/TILT
/
RECSTOP
PULL
/AUTO
ZOOM/
A-B
LAST
/ESC
DigitalDiskRecorder
WJ-HD
+
FWDREV
-
/
BUSY
SET
SETUP
SEARCH
SLOW
LISTED
REPEAT
GOTO
PRESET
IRIS
FOCUS
PAN/TILT
13 14 15 16
1211
10/0
9
5 6 7 8
4321
LOGOUT
MARK
OSD
SEQ
TEXT COPY
EL-ZOOM
SHIFT
MONITOR1
MONITOR2
ALARM
RESET
HDD2
HDD1
TIMER
ERROR
ALARM
ALARM
SUSPEND
OPERATE
DISKSELECT
S-ATA
S-ATA
7-10mm
Approx. 2mm
3-5mm
Approx. 17mm
SATA label(for top)
SATA label(for front)