Panasonic KV-SS905C User manual

ORDERNO. KM70108670C0
G14
High SpeedColorScanner
KV-SS905C
1
1

1. GENERALPRECAUTIONS
1.1. SafetyPrecautions
1. Beforeservicing, unplug thepowercord topreventelectrical shock hazard.
2. Whenreplacing parts, useronlymanufacture’srecommendedcomponents for
safety.
3. Check thecondition ofpowercord. Replace ifwearor damageisevident.
4. Afterservicing, besuretorestoretheleaddress, insulation barriers,
insulation papers, shields, etc.
5. Beforereturning theservicedequipmenttothecustomer, performthe
following electrical tests topreventshock hazard.
1.2. Electrical Tests
1. Unplug thepowercord and check for continuity betweentheearthground
connection on theplug and theInterface Board Cover. Thereshouldbezero
ohmresistance.
2. Withtheunitunplugged, shorttheAC live-neutral oftheplug withajumper
wire.
3. Turn ONthepowerswitch.
4. Measuretheresistance valuewithanohmmeterbetweenthejumperedAC
plug and anexposedmetal cabinet part, suchas screwheads, etc. (Referto
Fig.2)
Note
Someexposedparts may beisolatedfromthechassisbydesign. They read
infinity.
5. Ifthemeasurementisless than1M , apossibility for electricshock may exit.
Note
Thishazardouscondition must becorrectedbeforetheunitisreturnedtothe
end user.
2

Fig. 1
Fig. 2
1.3. ForService Technicians
ICsand LSIsarevulnerabletostaticelectricity. Whenrepairing, thefollowing
precautionswill helptopreventrecurring malfunctions.
1. Covertheplasticparts withaluminumfoil.
2. Ground thesoldering irons.
3

3. Use aconductive mat on theworktable.
4. DonotgraspICor LSIpinswithbarefingers.
2. SPECIFICATIONS
Items Specifications
Scanner
Scanning face Duplex
Sensor type Frontside:3-line(R, G, B) color CCD
Back side:3-line(R, G, B) color CCD
Readoutspeed Simplex scanning Approx. 98 (Binary)/ 97 (JPEG)ppm. *1
Duplex scanning Approx. 174 (Binary)/ 174 (JPEG)ipm. *1
Resolution Monochrome
scanning 100-600 dpi (1dpi step)
Color scanning 100-400 dpi (1dpi step)
Multi StreamTM
scanning Binary300dpi, Color 150dpi
Main-scanning direction and sub-scanning direction aresame
resolution.
Imageoutput Binary, Grayscale, Color, Multi-stream (Binaryand Color)
Tonal gradation Dither(64 stepgradation)
Error diffusion (64 stepgradation)
Imagecontrol Imageemphasis, Automaticthreshold, Dynamicthreshold,
Automatic
separation, Multi-Color dropout(Red, Green, Blue), Mirror image,
Reverse image, Noise reduction
Otherfunctions Patchcodedetection (Kodak patch2, 3, T, Control sheet),
Double
feeddetection
Paper Size 48×70 to298×420 mm (1.9”×2.75”to11.7”×17”)
Weight Singlepaperfeed:30 to157g/m2(8to42 lbs.)
Continuouspaperfeed:50 to157 g/m2(13 to42 lbs.)
Business card :Thickerthan127g/m2(34lbs)
AmountofMemory 64MBStandard (SODIMM)
1DIMM Slotfor anadditional memory
Powerrequirement AC100-120 V, 50/60 Hz
AC220-240 V, 50/60 Hz
Powerconsumption Scanning 3.0A(100-120V), 1.5A(220-240V)
Stand-by 0.7A(100-120V), 0.5A(220-240V)
Sleep 0.1A(100-120V), 0.06A(220-240V)
Environment
Operating Temperature 15 to30°C(59°Fto86°F)
Humidity 30%RH to80%RH
Storage Temperature 0to35°C(32°Fto95°F)
Humidity 10%RH to80%RH
4

Items Specifications
Unit
Dimensions(Width×
Depth×Height) 627×546×415 mm (24.7×21.5×16.3in.)
Weight 52 kgf(114.4lbs)
Accessories
Installation manual, Maintenance manual, ACcable, Blower,
Cleaning
paper, CD (ISIS driver, TWAINdriver, Capturesoftware(RTIV),
Operation manual, P.I.E. manual, RTIV manual Control sheet
images)
Option
Rollerexchangekit(KV-SS012), Rollercleaning paper(KV-
SS03),
-Imprinter(KV-SS05), Inkcartridge(KV-SS06), LampModule(
Front)
(KV-SS052), LampModule(Back)(KV-SS053)
Note
*1:These values depend on thefollowing scanning conditions.
- Multi StreamTM isTMofPixel Translations(a division ofAction Point, Inc.).
3. COMPONENTIDENTIFICATION
5

4. INSTALLATION
4.1. MinimumSpace Requirements
6

Besuretomaintaintherecommendedspace requirements for properventilation.
4.2. Installing theLamp
1. OpentheLampDoor.
2. InserttheFrontSideLampModuleintheFrontSideLampModuleSlotuntil
the“click”isheard.
3. InserttheBack SideLampModuleintheBack SideLampModuleSlotuntil the
“click”isheard.
4. Connect eachLampCabletoeachconnector.
5. Close theLampDoor.
7

8

4.3. Installing theExitStopper
1. Position theExitStopperagainst theDocumentWidthScale. (Securethe
guides inplace.)
-Use theExitStopperwhenneeded.
4.4. Installing theExitTrayStopper
1. SqueezetheendsoftheExitTray Stoppermetal guides slightlytogether, and
insertthemintotheStopperSlots oftheExitTray. Thenpull up theplastic
9

partofExitTray Stopper. (Install theExitTray Stopperinthesequence of(1)
through (3).)
4.5. DIMM ModuleExtension
Amaximumof256MBextendedmemorymay berequireddepending on the
combination ofthepapersize, resolution and gray scalemode.To determinehow
muchextendedmemoryisrequired, refertothesection 4.6“Additional Memory
Sizeeachscanning mode(MB)”.
*RecommendedDIMM
- JEDEC-standard 168pin, dual in-linememorymodule(DIMM)
- Non buffered
- Single+3.3V±0.3V powersupply
- Frequency/CAS Latency :100MHz/CL=2, 133MHz/CL=2, 133MHz/CL=3
- 64MB, 128MBor 256MBmay beused.
10

(Reference) DIMM modulewhichhas beenevaluatedusing thisscanner
- Manufacturer:DELKINDEVICES
1. Model No.:DM168-064Y3Q488-10S2P (64MB)
2. Model No.:DM168-064Y3Q446-10D2P (64MB)
3. Model No.:DM168-128Y3Q448-10D4P (128MB)
Note
Originally, I/FBoard (SCSIBoard)has 64MBmemoryas thestandard memory.
4.6. Additional MemorySizeeach scanning mode(MB)
4.6.1. Simplex / Grayscale8bit
Size Resolution (dpi)
100 200 300 400 500 600
A3 0 0 0 0 0 64
A4 0 0 0 0 0 0
A5 0 0 0 0 0 0
A6 0 0 0 0 0 0
B4(JIS) 0 0 0 0 0 0
B5(JIS) 0 0 0 0 0 0
B6(JIS) 0 0 0 0 0 0
Ledger 0 0 0 0 0 64
Legal 0 0 0 0 0 0
Letter 0 0 0 0 0 0
4.6.2. Duplex / Grayscale8bit
11

Size Resolution (dpi)
100 200 300 400 500 600
A3 0 0 0 0 64 128
A4 0 0 0 0 0 64
A5 0 0 0 0 0 0
A6 0 0 0 0 0 0
B4(JIS) 0 0 0 0 64 64
B5(JIS) 0 0 0 0 0 0
B6(JIS) 0 0 0 0 0 0
Ledger 0 0 0 0 64 128
Legal 0 0 0 0 0 64
Letter 0 0 0 0 0 64
4.6.3. Simplex / Binary
Size Resolution (dpi)
100 200 300 400 500 600
A3 0 0 0 0 0 0
A4 0 0 0 0 0 0
A5 0 0 0 0 0 0
A6 0 0 0 0 0 0
B4(JIS) 0 0 0 0 0 0
B5(JIS) 0 0 0 0 0 0
B6(JIS) 0 0 0 0 0 0
Ledger 0 0 0 0 0 0
Legal 0 0 0 0 0 0
Letter 0 0 0 0 0 0
4.6.4. Duplex / Binary
12

Size Resolution (dpi)
100 200 300 400 500 600
A3 0 0 0 0 0 0
A4 0 0 0 0 0 0
A5 0 0 0 0 0 0
A6 0 0 0 0 0 0
B4(JIS) 0 0 0 0 0 0
B5(JIS) 0 0 0 0 0 0
B6(JIS) 0 0 0 0 0 0
Ledger 0 0 0 0 0 0
Legal 0 0 0 0 0 0
Letter 0 0 0 0 0 0
4.6.5. Color(Simplex / Duplex)
Size Resolution (dpi)
100 200 300 400
A3 0/ 0 0/ 0 0/ 0 64 / 128
A4 0/ 0 0/ 0 0/ 0 0/ 64
A5 0/ 0 0/ 0 0/ 0 0/ 0
A6 0/ 0 0/ 0 0/ 0 0/ 0
B4(JIS) 0/ 0 0/ 0 0/ 0 64 / 128
B5(JIS) 0/ 0 0/ 0 0/ 0 0/ 64
B6(JIS) 0/ 0 0/ 0 0/ 0 0/ 0
Ledger 0/ 0 0/ 0 0/ 0 64 / 128
Legal 0/ 0 0/ 0 0/ 0 0/ 64
Letter 0/ 0 0/ 0 0/ 0 0/ 64
4.6.6. Multi Stream(Binary300dpi / Color150dpi)
Size Simplex Duplex
A3 0/ 0 0/ 0
A4 0/ 0 0/ 0
A5 0/ 0 0/ 0
A6 0/ 0 0/ 0
B4(JIS) 0/ 0 0/ 0
B5(JIS) 0/ 0 0/ 0
B6(JIS) 0/ 0 0/ 0
Ledger 0/ 0 0/ 0
Legal 0/ 0 0/ 0
Letter 0/ 0 0/ 0
13

4.7. Removing I/F Board (SCSI Board)
1. Make surethePowerisOFF.
2. Remove I/FBoard (SCSIBoard). (See 8.4.3)
4.8. Installing DIMM Module
1. InserttheDIMM Moduleintotheconnector on theI/FBoard (SCSIBoard), and
raise thetabsat thebothendsoftheconnector until they lock intoplace.
4.9. Installing theI/F Board (SCSI Board)
1. InserttheI/FBoard (SCSIBoard)intothescanneralong therailsand pushitin
firmlyunititconnects totheMOTHERBoard.
14

2. Tightenall thescrews.
15

4.10. Connecting theUnitto aPersonal Computer
Note
*AC cord shownon thefigureisfor AC100-120V.
Caution
Set thePowerSwitchon thescannerand on thepersonal computertoOFF
beforeconnecting theinterface cable. Use onlytheAC Cord that issuppliedby
manufacturer.
4.11. System Requirements
Whenusing thescanner, therequiredpersonal computerconditionsareas
follows.
CPU Pentium 266MHzor higher(Pentium , 1GHzprocessor or higheris
recommended.)
Memory 64 MBor higher(128 MBor higherisrecommended.)
OS Windows95 / Windows98 / WindowsNT/ Windows2000 / Windows
Me
I/FBoard (SCSI
Board) Adaptec Board SCSIcard AHA2940UW/ 29160 / 39160 Series are
recommended.
*Thescanning speeddiffersdepending on thepersonal computer’soperating
environmentor application.
16

4.12. LCD Settings
Beforescanning thedocument, performthepreferredsettingson thedisplay.
Setting information and scannerconditionsareshownon thedisplay.
17

4.12.1. Setting thelanguage
1. Turn thepoweron whilepressing theHOME key.
Note
Thelanguagesetting modeisselected
automaticallywhenthescanner’spoweristurnedon for thefirst timeafterthe
scannerwas purchased.
18

2. Use the[ ]key or [ ]key toselect the“EnglishLetter”, “EnglishA4”or
“DeutschA4”, “ ”.
3. Press theHOME key.
-Thedisplay will changetotheselect language, thenthescannerwill be
ready.
-Thissetting will remainuntil itischangedtoanothersetting.
4.12.2. Setting theSCSI IDand Terminator
1. Press theOTHERS key.
2. Press theMODE key.
19

Press theMODE key [ ]todisplay theSCSIID, whichisthefourthsetting.
3. Press theSELECT[ ]key or [ ]key toselect thedesiredsetting.
The[ ]key moves tothenext IDas shownbelow.
The[ ]key moves tothepreviousID.
-WideSCSIsetting
(Disable)
(Enable)
4. Press theMODE key [ ]toswitchtotheterminator setting.
To activate theSCSIIDand Terminator settings, press theHOME key toreturn
to"READY", thenturn theunitoff and on.
5. Press theSELECT[ ]key or [ ]key toselect thedesiredsetting.
The[ ]key moves tothenext contentas shownbelow.
The[ ]key moves tothepreviouscontent.
20