Panasonic KV-S5055C User manual

Model No. KV-S5055C
Installation Manual
These instructions contain information on installing the scanner. Please read this manual before installing the
unit.
For information on operating the scanner, please read the Operating Manual on the CD-ROM enclosed with this
unit.
Please carefully read this manual, and keep this documentation in a safe place for future reference.
High Speed Color Scanner

Introduction
Thank you for purchasing a Panasonic High Speed Color Scanner.
Feature Highlights
Superior Paper Feeding
•This scanner features an advanced paper-feeding mechanism that adjusts the pressure of the rollers and
the amount of time that the rollers are applied to the document according to the condition of the document.
As a result, this scanner can scan a wide range of paper weights, from very thin 20 g/m² (5 lbs.) paper to
very thick 157 g/m² (42 lbs.) paper.
High-speed Double Sided Scanning
•This scanner can scan documents at high speed, regardless of the image type (monochrome / color).
Single sided: 90 pages/minute, double sided: 180 images/minute (200 dpi)
Single sided: 60 pages/minute, double sided: 120 images/minute (300 dpi)
* Speeds based on scanning A4 size paper in landscape orientation.
Support for High-efficiency Scanning Jobs
•Self-cleaning function
This scanner contains an ionizer that, by emitting ions, reduces the amount of paper dust that accumulates
on the scanning glass. This scanner also has self-cleaning brushes that clean paper dust off of the scanner
glass.
•Stapled document detection
This scanner has a stapled document detection function that detects documents that contain staples and
stops scanning before any serious damage occurs.
•Double feed detection
This scanner contains ultrasonic sensors that detect double feeding. Double feeding can be detected even
if you scan documents that contain paper of various thicknesses.
•Double Feed Skip (DFS) function
If scanning has been stopped because a double feed was detected, you can easily resume scanning by
pressing the Double Feed Skip key (DFS key). When you scan documents that include items that you do
not want to be detected as double feeding (for example, documents that have receipts attached, envelopes,
etc.), the double feed detection function can be enabled and still scan these documents.
Other Features
•You can set the left and right document guides independently. By doing so, you can reliably scan
documents of differing paper sizes.
•The paper feed path can be opened widely to easily removed jammed paper and perform maintenance.
2 Installation Manual
Introduction

About the documentation
The scanner documentation consists of 2 manuals: the Installation Manual and the Operating Manual.
In addition, each piece of software includes the help.
Installation Manual
(this manual)
The Installation Manual explains the installation method and
procedures.
Operating Manual
(electronic documentation)
The Operating Manual explains the part names, operations, features
and maintenance of the unit.
The electronic documentation is located on the included CD-ROM. For
details on viewing the documentation, see "Viewing Electronic
Documentation" (page 20).
Software help
•You can view explanations about the settings for Panasonic Image
Enhancement Technology (PIE) functions that are available on the
ISIS driver screen and on the TWAIN driver screen by clicking the
help button that appears on each of the software's operation
screen.
•You can view explanations about the settings for Image Capture
Plus (ICP) by clicking the help button that appears on the
software's operation screen.
•You can view explanations for User Utility, which is used for
maintenance, by clicking the help button that appears on the
software's operation screen.
•You can also view the help for Image Capture Plus and User Utility from the Windows Start menu. For
details about viewing the help, see "Viewing Manuals and Help Installed On Your Computer" (page 20).
Abbreviations
•Windows® refers to the Microsoft® Windows® operating system (hereafter Windows).
•Windows® XP refers to the Microsoft® Windows® XP operating system (hereafter Windows XP).
•Windows Vista® refers to the Microsoft® Windows Vista® operating system (hereafter Windows Vista).
•Windows® 7 refers to the Microsoft® Windows® 7 operating system (hereafter Windows 7).
Trademarks
•Microsoft, Windows, Windows Vista, and Internet Explorer are either registered trademarks or trademarks
of Microsoft Corporation in the United States and/or other countries.
•ISIS is a registered trademark or trademark of EMC Corporation in the United States and other countries.
•IBM and AT are trademarks of International Business Machines Corporation in the United States, other
countries, or both.
•Intel and Intel Core are trademarks of Intel Corporation in the U.S. and other countries.
•Adobe and Reader are either registered trademarks or trademarks of Adobe Systems Incorporated in the
United States and/or other countries.
•All other trademarks identified herein are the property of their respective owners.
Installation Manual 3
Introduction

International ENERGY STAR Program
As an ENERGY STAR®Partner, Panasonic has determined that this product meets
the ENERGY STAR guidelines for energy efficiency.
Federal Communications Commission Requirements (For United States
only)
Note
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference in which case the user will be required to correct
the interference at his own expense.
FCC Warning: To assure continued FCC compliance, the user must use only shielded interface cable and
the provided power supply cord. Also, any unauthorized changes or modifications to this equipment would
void the user’s authority to operate this device.
For FRG Users (For Germany Only)
•Machine noise information regulation - 3.GPSGV, the maximum sound pressure level is 70 dB(A) or less,
in conformity with EN ISO 7779.
•This device is not intended for use in the direct field of view at visual display workplaces. To avoid
incommoding reflexions at visual display workplaces this device must not be placed in the direct field of
view.
4 Installation Manual
Introduction

Table of Contents
Before You Start .......................................................................................6
For Your Safety .................................................................................................................6
Safety Information (For United Kingdom only) ..............................................................9
Precautions ......................................................................................................................10
Installation ..............................................................................................12
Installing the Unit ............................................................................................................12
About Status Indicators ..................................................................................................16
Installing Software ..........................................................................................................17
System Requirements ....................................................................................................17
CD-ROM Contents .........................................................................................................17
Software Installation .......................................................................................................18
Uninstalling Software ......................................................................................................19
Viewing Electronic Documentation ...............................................................................20
Viewing Manuals From the CD-ROM .............................................................................20
Viewing Manuals and Help Installed On Your Computer ...............................................20
Uninstalling Manuals ......................................................................................................21
Appendix .................................................................................................22
Troubleshooting ..............................................................................................................22
Installation Manual 5
Table of Contents

For Your Safety
To prevent severe injury and loss of life, read this
section carefully before using the unit to ensure proper
and safe operation of your unit.
•This section explains the graphic symbols used
in this manual.
WARNING
Denotes a potential
hazard that could
result in serious
injury or death.
CAUTION
Denotes hazards
that could result in
minor injury or
damage to the unit.
These symbols are used to alert
operators to a specific operating
procedure that must be performed
carefully.
These symbols are used to alert
operators to a specific operating
procedure that must not be
performed.
These symbols are used to alert
operators to a specific operating
procedure that must be
emphasized in order to operate
the unit safely.
For Users
WARNING
Power and Ground Connection
The power source voltage of this unit is
listed on the nameplate.
Only plug the unit into an AC outlet with
the proper voltage.
If you use a cord with an unspecified
current rating, the unit or plug may emit
smoke or become hot to the touch.
When you operate this product, the power
outlet should be near the product and
easily accessible.
To ensure safe operation, the power cord
supplied must be inserted into a standard
three-prong AC outlet which is effectively
grounded (earthed) through the normal
wiring.
The fact that the equipment operates
satisfactorily does not imply that the
power point is grounded (earthed) and
that the installation is completely safe. For
your safety, if in any doubt about the
effective grounding (earthing) of the
power point, consult a qualified
electrician.
If the plug cannot be inserted into the AC
outlet, contact a licensed electrician to
replace the AC outlet with a properly
grounded (earthed) one.
Do not defeat the grounding (earthing)
plug (ex. do not use a conversion plug).
Plug the power cord firmly into an AC
outlet. Otherwise, it can cause fire or
electric shock.
Do not pull, bend, rest objects on, or chafe
the power cord and plug.
Damage to the power cord or plug can
cause fire or electric shock.
6 Installation Manual
Before You Start
Before You Start

Do not attempt to repair the power cord or
plug. If the power cord or plug is damaged
or frayed, contact your dealer for a
replacement.
Ensure that the plug connection is free of
dust. In a damp environment, a
contaminated connector can draw a
significant amount of current that can
generate heat, and eventually cause fire
if left unattended over an extended period
of time.
Never touch the plug with wet hands.
Danger of electric shock exists.
Stop operation immediately if the unit
emits smoke, excessive heat, abnormal
smell, or unusual noise. These conditions
can cause fire or electric shock.
Immediately turn the unit off, and unplug
the power cord, and contact your dealer
for service.
When disconnecting the unit, grasp the
plug instead of the cord. Pulling on a cord
forcibly can damage it, and cause fire or
electric shock.
Operating Safeguards
If metal fragments or water gets into the
unit, turn the unit off, and unplug the unit
immediately. Contact your dealer for
service. Operating the contaminated unit
can cause fire or electric shock.
Do not open covers, and do not attempt to
repair the unit yourself. Contact your
dealer for service.
Do not alter the unit or modify any parts.
Alteration or modification can cause fire or
electric shock.
During thunderstorms, do not touch the
unit and plug. It may cause an electric
shock.
Roller Cleaning Paper
Do not use the roller cleaning paper near
a heater or open flame.
Do not drink or inhale the roller cleaning
paper fluid including isopropyl alcohol.
The roller cleaning paper may be harmful
to sensitive skin. Please use protective
gloves.
Installation Manual 7
Before You Start

CAUTION
Power
The unit should be used only with the
power cord enclosed with the unit.
When the unit is not used over an
extended period of time, switch it off, and
unplug it. If an unused unit is left
connected to a power source for a long
period, degraded insulation may cause
electric shock, current leakage, or fire.
Installation and Relocation
Do not position the unit in a location where
it is unstable.
To prevent fire or shock hazard, do not
expose this unit to rain or any type of
moisture.
Do not place the unit in a hot humid or
dusty environment.
Prolonged exposure to these adverse
conditions may cause fire or electric
shock.
Do not block the air vents. Doing so can
cause heat to build up, and may result in
fire.
When moving the unit, be sure to unplug
the power cord from the AC outlet. If the
unit is moved with the power cord
attached, it can cause damage to the cord
which could result in fire or electric shock.
Do not use the exit tray hanging out of a
table.
When carrying the unit, do not use the
trays as handles.
Make sure that the unit is installed in a well
ventilated room so as not to increase
density of ozone in the air.
Since ozone is heavier than air, it is
recommended that air at floor level be
ventilated.
Move this unit with two persons, and hold
it by both side grips. Dropping the unit can
cause injury and damage to the unit.
Operating Safeguards
If the unit falls down or gets damaged, turn
the unit off, and unplug the power cord.
Otherwise, it may cause fire or electric
shock.
Do not place any liquids or heavy items on
the unit.
Accidental spillage of liquid into the unit
may cause severe damage. If this occurs,
turn the unit off, unplug the power cord,
and contact your dealer for service.
Do not touch the scanning glass or their
surroundings immediately after
continuous scanning.
This area is very hot and can cause burns.
Be careful not to pinch your fingers when
closing the ADF door. It can cause injury.
8 Installation Manual
Before You Start

Safety Information (For
United Kingdom only)
This appliance is supplied with a moulded three pin
mains plug for your safety and convenience.
A 5 amp fuse is fitted in this plug. Should the fuse need
to be replaced, please ensure that the replacement fuse
has a rating of 5 amps and that it is approved by ASTA
or BSI to BS1362. Check for the ASTA mark
ASA
or the
BSI mark on the body of the fuse. If the plug contains
a removable fuse cover, you must ensure that it is
refitted when the fuse is replaced. If you lose the fuse
cover, the plug must not be used until a replacement
cover is obtained. A replacement fuse cover can be
purchased from your local Panasonic Dealer.
IF THE FITTED MOULDED PLUG IS UNSUITABLE
FOR THE SOCKET OUTLET IN YOUR PREMISES,
THEN THE FUSE SHOULD BE REMOVED AND THE
PLUG CUT OFF AND DISPOSED OF SAFELY.
THERE IS DANGER OF SEVERE ELECTRICAL
SHOCK IF THE CUT-OFF PLUG IS INSERTED INTO
ANY 13 AMP SOCKET.
If a new plug is to be fitted, please observe the wiring
cord as shown below. If in any doubt, please consult a
qualified electrician.
WARNING
THIS APPLIANCE MUST BE EARTHED.
IMPORTANT
The wires in this mains lead are coloured as follows:
Green-and-Yellow : Earth
Blue : Neutral
Brown : Live
As the colours of the wires in the mains lead of this
apparatus may not correspond with the coloured
markings identifying the terminals in your plug, proceed
as follows.
The wire that is coloured GREEN-AND-YELLOW must
be connected to the terminal in the plug that is marked
with the letter E or by the Earth symbol or coloured
GREEN or GREEN-AND-YELLOW.
The wire that is coloured BLUE must be connected to
the terminal in the plug that is marked with the letter N
or coloured BLACK.
The wire that is coloured BROWN must be connected
to the terminal in the plug which is marked with the letter
L or coloured RED.
How to replace the fuse:
Open the fuse compartment with a screwdriver and
replace the fuse and fuse cover.
Installation Manual 9
Before You Start

Precautions
Installation
•Do not place the unit in direct sunlight, in a cold
draft, or near heating apparatus.
•Do not place the unit near apparatus which
generate electronic or magnetic noise.
•Protect the unit from static electricity.
•Do not move the unit immediately from a cold place
to a warm place. It may cause dew.
CD-ROM
•Do not write or stick paper on the front and/or back
of CD-ROM.
•Do not touch the data side of the CD-ROM. When
handling the CD-ROM, be careful not to leave
fingerprints or otherwise damage the CD-ROM.
•Do not leave the CD-ROM where it is directly
exposed to sunlight or near a heater for extended
periods.
•Do not throw or bend the CD-ROM.
Roller Cleaning Paper
•Keep the roller cleaning paper out of reach of small
children.
•Do not store the roller cleaning paper in direct
sunlight or in a place with a temperature over
40
°C
(104 °F).
•Only use the roller cleaning paper to clean the
rollers and scanning glass.
•For details about the roller cleaning paper, please
refer to the Material Safety Data Sheet (MSDS).
Please ask your Panasonic sales company about
obtaining the Material Safety Data Sheet.
KEEP AWAY FROM FIRE.
Replacement Parts
This unit includes the following replaceable parts. To
purchase replacements, contact your dealer.
•Double feed prevention roller*1
•Paper feed roller module*1
•Roller cleaning paper (KV-SS03)
*1 We recommend that this part be replaced periodically. When
purchasing a replacement, request a roller exchange kit
(KV-SS039). For details, see "Replacement Parts and Optional
Units" in the Operating Manual.
Others
•Make sure to remove paper clips and staples from
documents before scanning. Failing to do so can
damage the unit, document, or both.
•Do not use thinner, benzine, or cleaners containing
abrasives or surfactants, for cleaning the outside of
scanner.
•Plug the power cord into an outlet from which you
can easily unplug it.
10 Installation Manual
Before You Start

Illegal Duplication
It is unlawful to make duplication of certain
documents.
Duplicating certain documents may be illegal in
your country/area.
Penalties of fines and/or imprisonment may be
imposed on those found guilty. The following are
examples of items that may be illegal to duplicate
in your country/area.
•Currency
•Bank notes and checks
•Bank and government bonds, and securities
•Passports, licenses, official or private
documents, identification cards, and the like
•Copyright materials, or trademarks without
the consent of the owner
•Postage stamps, and other negotiable
instruments
This list is not inclusive, and no liability is
assumed for either its completeness or accuracy.
In case of doubt, contact your legal counsel.
Notice
Install your machine near a supervised area
to prevent illegal duplication from being
made.
Security Notice
The management of documents and scanned data is
the responsibility of the user. In particular, pay attention
to the following points.
•Make sure you have the same number of pages for
important documents both before and after
scanning, and take care not to leave any pages in
the scanner.
•Periodically back up important data.
•When having your computer or hard disk serviced,
or when disposing of your computer or hard disk,
completely erase any stored image data.
Installation Manual 11
Before You Start

Installing the Unit
About the installation location
•In order to ensure proper operation, install the unit
maintaining the proper distances from surrounding
objects, as shown in the following illustration.
200 mm
(7.9 in.)
250 mm
(9.8 in.)
Top view
200 mm
(7.9 in.)
200 mm
(7.9 in.)
CAUTION
•Move this unit with two persons, and hold it by
both side grips. Dropping the unit can cause
injury and damage to the unit.
Notice
•Do not move the unit immediately from a cold
place to a warm place. It may cause dew.
Initial Setup
1. Check the accessories.
•Check that all accessories are included before
installing the scanner.
In the event that an item is missing, please
contact your dealer.
Power cord
USB cable
Drivers & Utilities /
Manuals CD-ROM
Double feed
prevention roller
Shading paper
Roller cleaning paper
Blower
Installation Manual
(this manual)
Safety Guide*1
(for French, German,
Spanish, Italian,
Russian, and
Portuguese only)
*1 Safety Guide may be included depending on country/area.
12 Installation Manual
Installation
Installation

Note
•It is highly recommended to keep the
original carton and all packing materials.
They are necessary when repacking.
•[For United States only]
Applicable limited warranty information is
included on the Drivers & Utilities / Manuals
CD-ROM.
•Two power cords may be included. Use the
power cord appropriate for where you use
the unit.
2. Remove all packing tape.
3. Pull the ADF door release (A) towards you, and
open the ADF door (B).
12
4. Pull towards you and remove the double feed
prevention roller cover by using the indent (A).
1
5. Install the double feed prevention roller.
•Align the shaft that is shaped as indicated by
A with the notch in the roller mount (B), and
then insert the shaft in the notch. Push the shaft
on the opposite side (C) until it clicks into place.
1
1
32
2
Installation Manual 13
Installation

Notice
•After you install the double feed prevention
roller, make sure that the shaft is inserted
into the tab, and that the shaft will not rotate
or move. If the roller is not installed
correctly, it may cause double feeding or a
paper jam.
6. Insert the protrusion (A) of the double feed
prevention roller cover into the hole on the main
unit, and then push in the part of the roller cover
indicated by B in the direction indicated by the
arrow until it clicks into place.
2
1
Notice
•Make sure that the double feed prevention
roller cover does not stick up.
If the double feed prevention roller cover is
closed incompletely, damage or paper jams
can occur.
14 Installation Manual
Installation

7. Close the ADF door.
•Push both sides of the ADF door down slowly
until it clicks into place.
8. Connect the power cord and the USB cable to the
scanner.
Notice
•Use only the power cord that is provided
with the unit.
•Use the included USB cable or a certified
Hi-Speed USB 2.0 cable.
USB connector
To the computer
USB Cable
To the AC outlet
Power cord
AC inlet
9. Install software (page 17).
10. Set the power switch of the scanner to " " (ON).
•The ready indicator lights green.
Ready indicator
Power switch
Installation Manual 15
Installation

About Status Indicators
The status of the scanner is displayed by the ready indicator (A) and the error indicator (B), as shown in the
table below:
21
A Ready indicator
(Green)
B Error indicator
(Red) Status
ON OFF Ready
ON Blinking (Slow, Long ON)*1 Caution*4
OFF ON Error*4
Blinking (Slow, Long ON)*1 OFF Sleep
Blinking (Slow, Long ON)*1 Blinking (Slow, Long ON)*1 Caution*4 / Sleep
Blinking (Slow, Short ON)*2 OFF Standby*5
Blinking (Slow, Short ON)*2 Blinking (Slow, Long ON)*1 Caution*4 / Standby*5
Blinking (Fast)*3 OFF Warming up
Blinking (2 times consecutively) OFF Double Feed Skip mode
*1 On for 1 second and off for 1 second.
*2 On for 1 second and off for 3 seconds.
*3 On for 0.25 seconds and off for 0.25 seconds.
*4 Check the status of the scanner using User Utility.
*5 The scanner will enter Standby mode when no operation is performed for 30 minutes, to save power.
To use the scanner again, restart it by pressing any one of the buttons for more than 1 second. The time period before the scanner
enters Standby mode can be configured in User Utility.
(The default setting varies depending on the country/area.)
16 Installation Manual
Installation

Installing Software
System Requirements
Computer IBM® PC/AT® or compatible
machine with a CD-ROM drive
CPU Intel® Core™ 2 Duo, 1.8 GHz or
higher
Operating
System
Windows XP / Windows Vista /
Windows 7
Interface USB 2.0
Memory 1 GB or higher
Hard Disk 5 GB or more free space is
required.
Note
•The above system requirements may not satisfy
the requirements of all operating systems.
•The scanning speed differs depending on the
host computer's operating environment or the
application used.
•Due to the slower speed of USB 1.1, it is
recommended to use a USB 2.0 interface.
•If you connect the scanner to a USB hub, it is
not guaranteed to work.
CD-ROM Contents
Drivers
Device Driver
TWAIN*2
ISIS
Applications Image Capture Plus*3
Utilities User Utility
Manuals*1
Installation Manual
Operating Manual
Others
Control Sheet*4
Warranty Information (U.S.A. only)
*1 All manuals are in PDF format. To view manuals, Adobe®
Reader® must be installed.
*2 There is no TWAIN application on this CD-ROM.
*3 Image Capture Plus is our original application software, and
does not require either TWAIN driver or ISIS driver.
*4 The control sheets are stored as PDF files. For use them, print
the control sheets in the same size as the document pages to be
scanned. For details, refer to "Using Control Sheets" in the
Operating Manual.
Installation Manual 17
Installation

Software Installation
The software on the enclosed CD-ROM can be installed
on your computer.
You can select from the 4 installation methods below,
depending on your needs.
a. Complete: Install all of the CD-ROM components.
b. All Drivers & Utilities: Install all of the CD-ROM
components except for applications.
c. Custom: Install one of the drivers, utilities or
manuals.
d. Application: Select and install Image Capture Plus.
Notice
•Make sure to log on as an administrator to install
the software.
1. Set the power switch of the scanner to " " (OFF).
2. Insert the included CD-ROM into the CD/DVD drive
on your computer.
•If you have a feature called "Autorun" activated,
the installation process will start automatically.
•The setup window will appear.
Note
•If the AutoPlay dialog box is displayed in
Windows Vista or Windows 7, select
"CDRun.exe".
•If the program does not start automatically,
from [My Computer] ([Computer] in
Windows Vista or Windows 7), select the
CD/DVD drive, and then double-click
"CDRun.exe".
3. Select your scanner model.
4. Select the desired installation methods from the
"Installation" list on the left side of the screen.
•If you selected [Complete] or [All Drivers &
Utilities], continue to step 6.
•If you selected [Custom], continue to step 5.
•If you selected [Image Capture Plus] in
"Application", continue to step 6.
18 Installation Manual
Installation

5. If you selected [Custom] for the installation type in
step 4, select the item that you want to install.
6. Follow the instructions on the screen.
•In Windows Vista or Windows 7, if a window
appears with the message "Windows can’t
verify the publisher of this driver software",
continue with the installation by selecting
"Install this driver software anyway".
7. Set the power switch of the scanner to " " (ON).
•If you installed a device driver, it is necessary to
continue with the next step.
8. Follow the instructions of the hardware wizard to
complete the installation.
•The installation process is performed
automatically in Windows Vista or Windows 7.
Note
Continue with the installation even if a window
appears with the message "Digital Signature
was not found for this driver" or "has not passed
Windows Logo testing...".
Uninstalling Software
If you want to remove the software that is installed on
your computer, follow the procedure below to uninstall
them.
1. In Control Panel, open [Add or Remove Programs].
•In Windows Vista or Windows 7, select
[Uninstall a program].
2. Select the item that you want to uninstall.
•The software is displayed with the program
names below:
Software Program Name
Device driver Panasonic High Speed
Scanner Device Driver
X.XX*1
TWAIN KV-S5055C TWAIN
Driver
ISIS KV-S5055C ISIS Driver
Image Capture Plus Image Capture Plus
User Utility Panasonic Scanner User
Utility
*1 "X.XX" and the number that follows a program name are the
software version. When you upgrade the software, the
numbers above may be different from the actual software
version.
3. Follow the instructions on the screen.
Installation Manual 19
Installation

Viewing Electronic
Documentation
Viewing Manuals From the
CD-ROM
All manuals on the CD-ROM can be viewed using
Adobe Reader.
1. Insert the included CD-ROM into the CD/DVD drive
on your computer.
•If you have a feature called "Autorun" activated,
the installation process will start automatically.
•The setup window will appear.
Note
•If the AutoPlay dialog box is displayed in
Windows Vista or Windows 7, select
"CDRun.exe".
•If the program does not start automatically,
from [My Computer] ([Computer] in
Windows Vista or Windows 7), select the
CD/DVD drive, and then double-click
"CDRun.exe".
2. Select your scanner model.
3. Select a manual from the "Manuals" list on the right
side of the screen.
•The selected manual will open.
Note
•To view the electronic documentation,
Adobe Reader must be installed on your
computer. If your computer is connected to
the Internet, you can download Adobe
Reader by clicking the URL below
"Download Adobe® Reader®".
The URL is displayed in the "Manuals" list
on the setup screen.
Viewing Manuals and Help
Installed On Your Computer
If the manuals and software that were included on the
CD-ROM have been installed on your computer, you
can use the following procedure to view the manuals
and the software's help.
Note
•To install manuals on your computer, see
page 18.
To view the manuals
1. On the [Start] menu, point to [All Programs], then
[Panasonic], and select [Scanner Manuals].
2. Select the desired manual.
•The selected manual will open.
To view help
For Image Capture Plus
1. On the [Start] menu, point to [All Programs],
[Panasonic], [Image Capture Plus], and then select
[Image Capture Plus Help].
For User Utility
1. On the [Start] menu, point to [All Programs],
[Panasonic], [Scanner Tools], [User Utility], and
then select [User Utility Help].
Note
•We recommend that you view help using
Internet Explorer® 6.0 or later for Windows.
20 Installation Manual
Installation