Panasonic KX-TCD505HKM User manual

ORDERNO. KM40310260C3
TelephoneEquipment
KX-TCD505HKM/ KX-TCA151EM
Digital Cordless Phone
MetallicGreyVersion
(forHong Kong)
SPECIFICATIONS
1

2003 PanasonicCommunicationsCo., Ltd. All rights reserved.
Unauthorizedcopying and distribution isaviolation oflaw.
1. ABOUTLEADFREE SOLDER (PbF:Pbfree)
Note:
Intheinformation below, Pb, thesymbol for leadintheperiodictableofelements, will referto
standard solderor solderthatcontainslead.
Wewill use PbF solderwhendiscussing theleadfree solderusedinour manufacturing process
whichismadefrom Tin(Sn), Silver(Ag), and Copper(Cu).
Thismodel, and otherslike it, manufacturedusing leadfree solderwill have PbF stampedon the
PCB. For service and repairworkwesuggestusing thesametypeofsolderalthough, withsome
precautions, standard Pbsoldercanalsobeused.
Caution
-PbF solderhas amelting pointthat is50°F~70°F(30°C~40°C)
higherthanPbsolder. Please use asoldering iron with
temperaturecontrol and adjust itto700°F±20°F(370°C±10°C). In
2

case ofusing high temperaturesoldering iron, please becareful
nottoheat too long.
-PbF solderwill tend tosplashifitisheatedmuchhigherthanits
melting point, approximately1100°F(600°C).
-Ifyou must use Pbsolderon aPCB manufacturedusing PbF
solder, removeas muchoftheoriginal PbF solderas possibleand
besurethat anyremaining ismeltedpriortoapplying thePb
solder.
-Whenapplying PbF soldertodoublelayeredboards, please check
thecomponentsideforexcess whichmayflow ontotheopposite
side(See thefigurebelow).
1.1. SuggestedPbF Solder
Thereareseveral types ofPbF solderavailablecommercially. Whilethisproductismanufactured
using Tin, Silver, and Copper
(Sn+Ag+Cu), you canalsouse Tinand Copper(Sn+Cu)or Tin, Zinc, and Bismuth(Sn+Zn+Bi).
Please check themanufac
turer’sspecificinstructionsfor themelting pointsoftheirproductsand anyprecautionsfor
using theirproductwithother
materials.
Thefollowing leadfree (PbF)solderwiresizes arerecommendedfor service ofthisproduct:
0.3mm, 0.6mm and 1.0mm.
1.2. How torecognizethat PbFree solderisused
1.2.1. Base UnitPCB
3

(ComponentView)
(FlowSolderSideView)
Note:
Thelocation ofthe“PbF“markissubjecttochangewithoutnotice.
1.2.2. Handset PCB
(ComponentView)
(FlowSolderSideView)
Note:
Thelocation ofthe“PbF“markissubjecttochangewithoutnotice.
1.2.3. ChargerUnitPCB
Note:
Thelocation ofthe“PbF“markissubjecttochangewithoutnotice.
2. FORSERVICE TECHNICIANS
ICsand LSIsarevulnerabletostaticelectricity.
Whenrepairing, thefollowing precautionswill helppreventrecurring malfunctions.
1. Covertheplasticparts boxes withaluminumfoil.
2. Ground thesoldering irons.
3. Use aconductivemat on theworktable.
4. DonottouchICorLSI pinswithbarefingers.
3. CAUTION
Dangerofexplosion ifbatteryisincorrectlyreplaced. Replace onlywiththesameor equivalent
typerecommendencedbythemanufacturer.
Dispose ofusedbatteries according tothemanufacture’sInstructions.
4. BATTERY
4.1. BatteryInstallation
Please ensurethebatteries areinsertedas shown. partshouldbeinsertedfirst.
Close thecoveras indicatedbythearrow.
4

-Whenyou replace thebatteries, partshouldberemovedfirst.
4.2. BatteryCharge
Atthetimeofshipment, thebatteries arenotcharged. Tocharge, place thehandseton thebase
unit.
Please chargethebatteries for about7hoursbeforeinitial use. During charging, thechargeLED
will lightas shownbelow.
Thehandsetwhichpowerisoff will beturnedon automaticallywhenitisplacedon thebase unit.
Thehandsetwill notoperatewhileitison thebase unit.
Ifyou do notrechargethehandsetbatteryfor morethan15 minutes, thedisplay will flash
whenthehandsetisliftedoff thebase unit.
5

Notefor Service:
-Thebatterystrengthmaynotbeindicatedcorrectlyifthebatteryis
disconnectedand connectedagain, evenafteritisfullycharged.
Inthat case, byrecharging thebatteryas mentionedabove, you
will get acorrect indication ofthebatterystrength.
-Confirmation ofAntennaPict ( ) indication:
IfAntennaPict isindicated, chargetimeisabout7hours.
However, ifAntennaPict isflashing, chargetimebecomes long.
4.3. BatteryInformation
Afteryour Panasonicbatteryisfullycharged:
Ni-MHBatteries (typical 700 mAh)
Operation Operating Time
Whileinuse (TALK) 10 hrsapprox.
Whilenotinuse (Standby) 120 hrsapprox.
Ni-CdBatteries (typical 250 mAh)
Operation Operating Time
Whileinuse (TALK) 4hrsapprox.
Whilenotinuse (Standby) 40 hrsapprox.
-Times indicatedareforpeak performance.
-Thebatteryoperating timemaybeshorteneddepending on usage
conditionsand ambienttemperature.
-Cleanthechargecontacts ofthehandset and thebase unitwitha
soft, drycloth. Cleaniftheunitissubject togrease, dust orhigh
humidity.
Otherwise thebatterymaynotchargeproperly.
-Thebatteries cannotbeoverchargedunless theyarerepeatedly
removedand replaced. Formaximumbatterylife, itis
6

recommendedthat thehandset notberechargeduntil thebattery
icon flashes .
4.4. Replacing theBatteries
Ifthe icon flashes afterafewtelephonecallsevenwhenthehandsetbatteries have
beenfullycharged, bothbatteries mustbereplaced.
-Chargenew batteries forapproximately7hoursbeforeinitial use.
(Thetelephonelinecordmust notbeconnectedtothetelephone
socket at thistime).
Whenreplacing thebatteries, ensurethat thecorrect batterytype
isselected.
-Whenreplacing thebatteries, besuretoset up thebatterytype
evenifyou install thesametypeofbatteries toinitialise battery
remaining memoryofyourhandset.
-Thefactorypreset is .
-To exittheoperation, press anytime.
-Donotuse non-rechargeablebatteries. Ifnon-rechargeable
batteries arefittedand startcharging, itmaycause theleakageof
thebatteryelectrolyte.
-Press thenotchon thecoverfirmlyand slideitas indicatedbythe
arrow. Replace bothbatteries and close thecoverthenchargethe
handset forabout7hours.
7

Please use PanasonicAAA typerechargeablebatteries.
Notefor Service:
-WhenNi-Cdbatteies arefittedwiththe
setting in ,
icon mightdisappearand stop charging evenifthe
handset ison thecradleforavoiding overcharge.
5. LOCATIONOFCONTROLS
5.1. Base Unit
5.2. Handset
8

9

6. SETTINGS
Location:
-Formaximumdistance and noise-free operation, place yourbase
unit:
-Awayfromelectrical appliances suchas TVs, radios, personal
computersorotherphones.
-Inaconvenient, high, and central location.
6.1. Connection
6.1.1. Base Unit
Plug intheACadaptor and thetelephonelinecord inorder1, 2, 3, 4.
10