Panasonic TY-TP65P30K () User manual

© Panasonic Corporation 2012
Unauthorized copying and distribution is a violation
of law.
ORDER NO. ITD1202004CE
Touch Panel
Model No. TY-TP65P30K

TY-TP65P30K
2
TABLE OF CONTENTS
PAGE
1Warning--------------------------------------------------------------3
1.1. Prevention of Electrostatic Discharge (ESD)
to Electrostatically Sensitive (ES) Devices ----------3
1.2. About lead free solder (PbF) ----------------------------4
2 Service Navigation------------------------------------------------5
2.1. Service Hint--------------------------------------------------5
3 Specifications ------------------------------------------------------6
4 Troubleshooting Guide------------------------------------------7
4.1. Diagnostic method of Bad P.C.B. ----------------------7
5 Disassembly and Assembly Instructions -----------------7
5.1. Cautions of Disassembling ------------------------------7
5.2. Removal of the Touch Panel ----------------------------7
5.3. Removal of CPU/X-LED1(Complete),
(Complete), X-LED3(Complete),
(Complete) and X-LED5(Complete) ------------ 7
5.4. Removal X-PHOTO1(Complete),
(Complete) , X-PHOTO3(Complete),
(Complete) ------ 8
5.5. Removal (Complete),
(Complete) and Y-LED3(Complete) ---------------- ---8
5.6. Removal Y-PHOTO1(Complete),
(Complete) --------------------9
6 Exploded View and Replacement Parts List ----------- 10
X-LED2
X-LED4
------
of X-PHOTO2
X-PHOTO4
and X-PHOTO5(Complete) --------
of Y-LED1 Y-LED2
of Y-PHOTO2
Y-PHOTO3(Complete)

TY-TP65P30K
3
1Warning
1.1. Prevention of Electrostatic Discharge (ESD) to Electrostatically Sensi-
tive (ES) Devices
Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Elec-
trostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and
semiconductor “chip” components. The following techniques should be used to help reduce the incidence of component damage
caused by electrostatic discharge (ESD).
1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your
body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap,
which should be removed for potential shock reasons prior to applying power to the unit under test.
2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as alumi-
num foil, to prevent electrostatic charge buildup or exposure of the assembly.
3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.
4. Use only an anti-static solder removal device. Some solder removal devices not classified as “anti-static (ESD protected)” can
generate electrical charge sufficient to damage ES devices.
5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.
6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most
replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or compara-
ble conductive material).
7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material
to the chassis or circuit assembly into which the device will be installed.
Caution
Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.
8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise ham less motion such as the brush-
ing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD) sufficient
to damage an ES device).

TY-TP65P30K
4
1.2. About lead free solder (PbF)
Note: Lead is listed as (Pb) in the periodic table of elements.
In the information below, Pb will refer to Lead solder, and PbF will refer to Lead Free Solder.
The Lead Free Solder used in our manufacturing process and discussed below is (Sn+Ag+Cu).
That is Tin (Sn), Silver (Ag) and Copper (Cu) although other types are available.
This model uses Pb Free solder in it’s manufacture due to environmental conservation issues. For service and repair work, we’d
suggest the use of Pb free solder as well, although Pb solder may be used.
PCBs manufactured using lead free solder will have the PbF within a leaf Symbol PbF stamped on the back of PCB.
Caution
• Pb free solder has a higher melting point than standard solder. Typically the melting point is 50 ~ 70 °F (30~40 °C) higher. Please
use a high temperature soldering iron and set it to 700 ± 20 °F (370 ± 10 °C).
• Pb free solder will tend to splash when heated too high (about 1100 °F or 600 °C).
If you must use Pb solder, please completely remove all of the Pb free solder on the pins or solder area before applying Pb sol-
der. If this is not practical, be sure to heat the Pb free solder until it melts, before applying Pb solder.
• After applying PbF solder to double layered boards, please check the component side for excess solder which may flow onto the
opposite side. (see figure below)
Suggested Pb free solder
There are several kinds of Pb free solder available for purchase. This product uses Sn+Ag+Cu (tin, silver, copper) solder. How-
ever, Sn+Cu (tin, copper), Sn+Zn+Bi (tin, zinc, bismuth) solder can also be used.

TY-TP65P30K
5
2 Service Navigation
2.1. Service Hint
P.C.B. Arrangement

TY-TP65P30K
6
3 Specifications
Type Touch Panel
Power source
Voltage +5V DC ± 10%
Electric current +5V DC Max. 500 mA
Supply method From USB bus
Touch Panel
Detection system Infrared ray interruption detection
Panel window 5713/16” (1468.1 mm) (W) ×333/64” (839.1 mm) (H)
Detection range 561/2“ (1435 mm) (W) ×3145/64” (805 mm) (H)
Effective detection range Above detection range + 1.0 mm around all sides
Resolution 2297 (W) ×1289 (H)
Detection pitch 7/64” (2.5 mm) ×7/64” (2.5 mm)
Output system Coordinate output
Number of optical elements 288 (W) ×162 (H)
Optical element pitch 13/64” (5.0 mm) (W) ×13/64” (5.0 mm) (H)
Minimum stylus 9/32” (7.0 mm) (W) ×9/32” (7.0 mm) (H)
Interface
USB1.1 compliant
Signals: +DATA, -DATA, VCC, GND
Temperature When operating: 0 ~ 40°C (Temperature gradient 25°C /Hr or less) *1
Humidity When operating: 20 ~ 80% (No dewing) *1
Resistance to external light Lateral light 2,000 lx or higher (20°angle of incidence)
Frontal light 10,000 lx or higher (90°angle of incidence)
Panel shape Flat panel (Flat type)
External dimensions
(excluding projections and mounting brackets)
6133/64” (1,562.2 mm) (W) ×363/4” (933.2 mm) (H) ×31/64” (12 mm) (D)
Mass Approx. 7.28 lb. (3.3 kg)
Escutcheon material Aluminum
Computer IBM PC/AT compatible machine with USB ports
OS
Windows XP (SP2 or later, 32 bit or 64 bit)
Windows Vista (32 bit or 64 bit)
Windows 7 (SP1 or later, 32 bit or 64 bit)
*1 For the touch panel only (when mounted to the main device, it follows the conditions of the main device.)

TY-TP65P30K
7
4 Troubleshooting Guide
4.1. Diagnostic method of Bad P.C.B.
• The diagnostic software “TDxx3UFtestPG“ enables the diagnostic of the P.C.B. and the identification of the defective P.C.B..
Click here for downloading the diagnostic software “TDxx3UFtestPG“.
• Unzip downloaded “soft_check_P30e.zip“ to extract the original files “TDxx3UFtestPG.exe“ and “Diagnostic_Manual_e.pdf“ in
folder “TDxx3UFtestPGe“.
• To use the product connecting with a Windows XP computer, the touch panel driver must be installed.
(Refer to Touch Panel Driver Software Installation Manual.)
4.2. Diagnostic procedures
1. Install the diagnostic software “TDxx3UFtestPG.exe“.
2. Connect the USB cable for the touch panel to the computer.
3. Start the installed software “TDxx3UFtestPG.exe“.
4. Use the self-test.
5. Confirm each block with the photo transistor output level test.
(Verify that the outputs of all elements are 200mV or more at gain zero with a PDP connected.)
6. Identify the defective blocks with the gain switching test (0 to 3).
(If the photo transistor output level is 200mV or less at gain zero, then replace the corresponding P.C.B..)
7. Identify the defective P.C.B. with the LED current verification.
■Please refer to the how to use the diagnostic software “TDxx3UFtestPG“ and how to identify the defective P.C.B..
4.3. Diagnostic method

TY-TP65P30K
8
5 Disassembly and Assembly Instructions
5.1. Cautions of Disassembling
• When disassembling the P.C.B., use Philips screwdriver
#1(with a diameter of 5mm) .
• and marks indicate screw positions.
5.2. Removal of the Touch Panel
1. Remove the 4 Attachment Bracket_2’s and then remove
the Touch Panel.
2. Turn over the Touch Panel.
3. Remove 8 screws and then remove 2 Attachment
Bracket_1 Top’s and 2 Attachment Bracket_1 Bottom’s.
5.3. Removal of CPU/X-LED1(Com-
plete), X-LED2(Complete), X-
LED3(Complete), X-LED4(Com-
plete) and X-LED5(Complete)
1. Remove the Touch Panel.
(Refer to removal of the Touch Panel.)
2. Remove 4 screws ( ) and then remove 2 Corner
Piece’s.
3. Remove 5 screws ( ) and then remove the Escutcheon
XL Assy.
4. Turn over the Touch Panel (turn to the front).
5. Remove double-sided tapes on the back side of each
flexible cable.
6. Remove screws of the P.C.B..
7. Turn over the P.C.B. and then remove the flexible cables
from it.
(Remove the USB Cable when CPU/X-LED1(Complete)
is replaced.)
8. Remove the P.C.B..
5.4. Removal of X-PHOTO1(Com-
plete), X-PHOTO2(Complete) ,
X-PHOTO3(Complete), X-
PHOTO4(Complete) and X-
PHOTO5 (Complete)
1. Remove the Touch Panel.
(Refer to removal of the Touch Panel.)
2. Remove 4 screws ( ) and then remove 2 Corner
Piece’s.

TY-TP65P30K
9
3. Remove 6 screws ( ) and then remove the Escutcheon
XP.
4. Turn over the Touch Panel (turn to the front).
5. Remove double-sided tapes on the back side of each
flexible cable.
6. Remove screws of the P.C.B..
7. Turn over the P.C.B. and then remove the flexible cables
from it.
8. Remove the P.C.B..
5.5. Removal of Y-LED1(Complete),
Y-LED2(Complete) and Y-
LED3(Complete)
1. Remove the Touch Panel.
(Refer to removal of the Touch Panel.)
2. Remove 4 screws ( ) and then remove 2 Corner
Piece’s.
3. Remove 9 screws ( ) and then remove the Escutcheon
YL and Cover.
4. Turn over the Touch Panel (turn to the front).
5. Remove double-sided tapes on the back side of each
flexible cable.
6. Remove screws of the P.C.B..
7. Turn over the P.C.B. and then remove the flexible cables
from it.
8. Remove the P.C.B..
5.6. Removal of Y-PHOTO1(Com-
plete), Y-PHOTO2(Complete)
and Y-PHOTO3(Complete)
1. Remove the Touch Panel.
(Refer to removal of the Touch Panel.)
2. Remove 4 screws ( ) and then remove 2 Corner
Piece’s.
3. Remove 6 screws ( ) and then remove the Escutcheon
YP.
4. Turn over the Touch Panel (turn to the front).
5. Remove double-sided tapes on the back side of each
flexible cable.
6. Remove screws of the P.C.B..

TY-TP65P30K
10
7. Turn over the P.C.B. and then remove the flexible cables
from it.
8. Remove the P.C.B..

TY-TP65P30K
11
6 Exploded View and Replacement Parts List
Please click the radio button for “Diagrams ll / Parts List” on the menu bar.

Model No. : TY-TP65P30K Exploded View

Model No. : TY-TP65P30K Accessories

Model No. : TY-TP65P30K Packing

Model No. : TY-TP65P30K Parts List
Safety Ref.
No. Part No. Part Name & Description Q'ty Remarks
22 TXJCN11MFW USB CABLE 1
39 TSCFZ0010036 FFC CABLE1(COMPLETE) 1 (X-LED4/X-LED5)
40 TSCFZ0010037 FFC CABLE2(COMPLETE) 1 (X-LED3/X-LED4)
41 TSCFZ0010038 FFC CABLE3(COMPLETE) 1 (X-LED2/X-LED3)
42 TSCFZ0010039 FFC CABLE4(COMPLETE) 1 (X-LED1/X-LED2)
43 TSCFZ0010040 FFC CABLE5(COMPLETE) 1 (X-LED1/Y-LED1)
44 TSCFZ0010041 FFC CABLE6(COMPLETE) 1 (Y-LED1/Y-LED2)
45 TSCFZ0010042 FFC CABLE7(COMPLETE) 1 (Y-LED2/Y-LED3)
46 TSCFZ0010043 FFC CABLE8(COMPLETE) 1 (X-PHOT5/Y-LED3)
47 TSCFZ0010044 FFC CABLE9(COMPLETE) 1 (X-PHOT4/X-PHOT5)
48 TSCFZ0010045 FFC CABLE10(COMPLETE) 1 (X-PHOT3/X-PHOT4)
49 TSCFZ0010046 FFC CABLE11(COMPLETE) 1 (X-PHOT2/X-PHOT3)
50 TSCFZ0010047 FFC CABLE12(COMPLETE) 1 (X-PHOT1/X-PHOT2)
51 TSCFZ0010048 FFC CABLE13(COMPLETE) 1 (X-PHOT1/Y-PHOT3)
52 TSCFZ0010049 FFC CABLE14(COMPLETE) 1 (Y-PHOT2/Y-PHOT3)
53 TSCFZ0010050 FFC CABLE15(COMPLETE) 1 (Y-PHOT1/Y-PHOT2)
1 THEC192N SCREW(3*4) 60
2 THEC191J SCREW(3*6) 34
3 THEA2539 PC BOLT 8
4 TMXA0521 CORNER PIECE 4
7 TUXA3911 CORNER INNER 4
8 TXFKE011QFW ESCUTCHEON XL ASSY 1
9 TXFKU011QFW REAR COVER XL ASSY 1
12 TKUX23601 REAR COVER YP 1
13 TKEA21701 ESCUTCHEON YP 1
14 TKUX23401 REAR COVER XP 1
15 TKEA21501 ESCUTCHEON XP 1
16 TKUX23501 REAR COVER YL 1
17 TKEA21601 ESCUTCHEON YL 1
54 TKKL55361 COVER 1
55 TBMA224 PANASONIC BADGE 1
65 THEC191J SCREW(3*6) 8
23 TXNXL111QFW CPU/X-LED1(COMPLETE) 1
24 TXNXL211QFW X-LED2(COMPLETE) 1
25 TXNXL311QFW X-LED3(COMPLETE) 1
26 TXNXL411QFW X-LED4(COMPLETE) 1
27 TXNXL511QFW X-LED5(COMPLETE) 1
28 TXNYL111QFW Y-LED1(COMPLETE) 1
29 TXNYL211QFW Y-LED2(COMPLETE) 1
30 TXNYL311QFW Y-LED3(COMPLETE) 1
31 TXNXP111QFW X-PHOTO1(COMPLETE) 1
32 TXNXP211QFW X-PHOTO2(COMPLETE) 1
33 TXNXP311QFW X-PHOTO3(COMPLETE) 1
34 TXNXP411QFW X-PHOTO4(COMPLETE) 1
35 TXNXP511QFW X-PHOTO5(COMPLETE) 1
36 TXNYP311QFW Y-PHOTO3(COMPLETE) 1
37 TXNYP211QFW Y-PHOTO2(COMPLETE) 1
38 TXNYP111QFW Y-PHOTO1(COMPLETE) 1
6 TPCC97801 CARTON TOP 1
10 TPCC97901 CARTON BOTTOM 1
11 TPDF26981 TOP PAD 2
20 TPDX00861 PP BAND(W=15 L=280) 2
21 TPDX00831 PP BAND STOPPER 2
18 TPEH663 ANTISTATIC BAG 1
19 TXFPD011QFW SEPARATION ASSY 1
5 TQZJ400 MANUAL 1
59 T9ZC243 CD-ROM 1
67 T9ZC252 EXTENSION USB CABLE 1
60 TKLA5301 ATTACHMENT BRACKET_1 TOP 2
61 TKLA5401 ATTACHMENT BRACKET_1 BOTTOM 2
62 TKLA5501 ATTACHMENT BRACKET_2 4
68 TKRA76801 TOUCH PEN 2

Model No. : TY-TP65P30K Parts List
Safety Ref.
No. Part No. Part Name & Description Q'ty Remarks
56 TPDF26851 ACCESSORIES BOX 1
57 TPDF26861 SEPARATION 1 1
58 TPDF26871 SEPARATION 2 1
63 TQEF176 A4 POLY BAG 1
64 TQEF174 POLY BAG WITH ZIPPER 1
69 TQEF176 A4 POLY BAG 1
66 TQEF174 POLY BAG WITH ZIPPER 1