Panasonic ER2031 User manual

© 2007 Matsushita Electric Works, Ltd. All rights
reserved. Unauthorized copying and distribution is a
violation of law.
Order Number SD0705M38CE
AC/Rechargeable Beard/Hair Trimmer
Model No. ER2031
ER2051
Middle East
TABLE OF CONTENTS PAGE PAGE
1 Warning-------------------------------------------------------------- 2
2 Specifications ----------------------------------------------------- 2
3 Troubleshooting Guide----------------------------------------- 3
4 Disassembly and Assembly Instructions ---------------- 4
5 Wiring Connection Diagram ---------------------------------- 5
6 Schematic Diagram---------------------------------------------- 5
7 Exploded View and Replacement Parts List ------------ 6

2
1Warning
Caution:
• Pb free solder has a higher melting point that standard solder; Typicall the melting point is 50 - 70°F (30 - 40°C) higher. Please
use a soldering iron with temperature control and adjust it to 750 ± 20°F (400 ± 10°C). In case of using high temperature solder-
ing iron, please be careful not to heat too long.
• Pb free solder will tend to splash when heated too high (about 1100°F / 600°C).
2 Specifications

3
3 Troubleshooting Guide

4
4 Disassembly and Assembly Instructions
4.1. Disassembly Instructions
1. Remove the attachment and the blade.
2. Loosen two screws tightening the blade springs and one housing screw.
3. Separate the housing A and B with care of four hooks on the housing A side.
4. Take out the motor.
5. Remove the rechargeable battery from the module.
4.2. Assembly Instructions
1. Place the switch handle, switch plate with springs and
the blade release button onto Housing A.
2. Set the rack with the lowest position.
3. Push the click spring into Housing A.
NOTE: If the click spring is not pressed completely, it
causes the chink between Housing A and B.
4. Place the module block and insert the insulating sheet
between module and plug chassis.
5. Place the motor.
6. Make sure that the rack is set to the lowest position and
set the dial with fitting position “1” into the edge of Hous-
ing A.
7. Check the position of click spring between the cog of dial.
8. Assemble Housing B onto Housing A.
9. Tighten three screws and attach the blade block.

5
5 Wiring Connection Diagram
5.1. ER2031
5.2. ER2051
6 Schematic Diagram

Model No. : ER2031 Exploded View for ER2031
7 Exploded View and Replacement Parts List

Model No. : ER2031 Parts List
Safety
Ref.
No. Part No. Part Name & Description Q'ty Remarks
1 WER964EP BLADE BLOCK 1
2 WER203K6008 P-TIGHT SCREW 3 K2-8
3 WER300R0167 SPRING FOR CUTTER 1ST
4 WER2031K3058 HOUSING A 1
5 WER2031K3068 HOUSING B 1
6 WER203K3268 LOCK RELEASE BUTTON 1
7 WER550V0197 SPRING 1
8 WER203K0288 RACK 1
9 WER203L1578 CLICK SPRING 1
10 WER203K3208 SWITCH HANDLE 1
11 WER203L3578 SWITCH TERMINAL PLATE 1
12 WER2031L0308 SHEET 1
13 WER203K3288 DIAL 1
14 WER203L1008 MOTOR 1
15 WER2031L2508 RECHARGEABLE BATTERY 1 Ni-Cd TYPE
16 WER2031L2108 MODULE 1
17 WER203K7398 COMB ATTACHMENT 1
18 WER200B2069 POWER CORD 1 C-2 PLUG
19 WER203X7918 OIL 1
20 WER210B7077 CLEANING BRUSH 1
21 WER203K7008 SOFT CASE 1
- WER2031K8008 INDIVIDUAL BOX 1
- WER2031K8108 OPERATING INSTRUCTIONS 1