Panduit PANZONE PZBASE3 User manual

INSTRUCTIONS CM336
© Panduit Corp. 2007
FOR TECHNICAL SUPPORT www.panduit.com/resources/install_maintain.asp
Venting for a 4" Fan
(view shown with door removed)
Knockout for.50” and.75”
Conduit (4 plcs.)
Knockout for 1.75" and 2"
Conduit (24 plcs.)
Louvered Vents
Reversible Door Hinge Location
Rotating Bracket Accepts up to 3
rack units of patch panels
(shown in the up position)
High Voltage Shield
Space available for a Double Gang
Electrical Box (2 plcs.)
Grounding Studs located on both
the Door and Enclosure Base Knockouts for T70
Raceway
(6 plcs.)
List of Components:
(1) 36" Edge Grommet
(1) Roll of TAK-TAPE (TTS-20R0)
(1) Installation Instruction
(2) Grounding Cable
(2) Port ID Labels
(6) Screw Caps
(3) PZBR3
(2) #10-24 Acorn Nuts
(2) Washers
(20) Thread Cutting Screws
(3) 3’ Sections of Hinged 2” X 2” Panel Duct
Knockouts for Wireless
Antennas
Page 1 of 6
PANZONE Building Automation Systems
Enclosure PZBASE3
PZBASE3

INSTRUCTIONS CM336
For Technical Support: www.panduit.com/resources/install_maintain.asp
1.6a 1.6b
Knockout
Knockout
Option 1 Option 2
1.2
26"
(To Junction Box)
6'
Floor
2 X 4 Stud
Center hole
for security screw
Top
Mounting eyelets
16"
32"
Bottom
Mounting eyelets
Step 1: Mounting Enclosure to Wall / Electrical Box Installation
1.1 Locate the wall studs (16" on center in most U.S.
cases).
1.2 Center enclosure over 3 studs drill holes for 5/16”
lag bolts for top mounting eyelets first. (2 places)
Note: Lag bolts not supplied
1.3 Install top lag bolts leaving a gap the thickness of
the enclosure sheet metal.
1.4 Hang enclosure on top lag bolts and tighten.
1.5 Install lower lag bolts. (2 places)
1.6 Install lag bolt at center hole to prevent vertical
movement.
If Mounting Electrical Box inside Enclosure:
Determine which side of enclosure the electrical
box will be mounted. There are two options for
routing the conduit when mounting the electrical
box inside the enclosure.
Option 1 - Inside of Enclosure: Mount electrical
box on desired side of enclosure using PEM
studs (nuts not included). Remove knockout from
top of enclosure on corresponding side of
mounted electrical box. Run conduit through
knockout hole along inside edge of enclosure to
the electrical box. (See figure 1.6a)
Option 2 - Outside of Enclosure: Remove knock-
out from side of enclosure the electrical box will
be mounted. Mount the electrical box. Run con-
duit along the outside of enclosure and connect
to electrical box through the knockout hole (See
figure 1.6b).
Page 2 of 6

INSTRUCTIONS CM336
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 3 of 6
Step 2: Door and Lock Installation
2.1 Determine from what side the door will hinge. Pay
attention to how close the enclosure is to a corner, a
door, or any other object that may obstruct the opening
of the door.
2.2 Use the carriage bolts,lock washer and nuts to attach
the hinges. Snap the two retaining rings into the groove
on the hinge pin. Insert hinge pins in the base side
hinges. (See figure 2.2)
Note: Slots in door and base allow door to be positioned
relative to base for improved fit. Perform step 2.3 before
tightening hinge nuts.
2.3 Lift door and position perpendicular to the base. Slide
door down into place.
2.4 Determine if the installation requires the door lock hasp
(supplied) or the keyed locks (sold separately).
Door Lock Hasp Installation:
Knockout the two holes on the opposite side of the
hinges in the middle of the enclosure on both the
base and the door (See figure 2.4a). Attach the latch
to the base and the catch to the door using supplied
#10-32 size screws and nuts. Plug 8 existing holes
with supplied hole caps.
Keyed Locks Installation: (sold separately)
Knockout the two large holes directly opposite from
the hinges on the cover. Slide in lock body and then
slide lock guide over the lock body. Attach lock hook
with supplied screw.(See figure 2.4b). Plug 8 existing
holes with supplied hole caps.
2.2
Retaining Ring
2.4a
2.4b
Hole Cap
Lock Guide
Step 3: Grounding
3.1 PANDUIT recommends the use of STRUCTUREDGROUND
Enclosure Grounding kit (PZAEGK) for grounding the
PANZONE Building Automaton Systems Enclosure
3.2 Attach grounding bracket as shown in figure 3.2.
3.3 Attach main building ground to bracket.
3.4 Attach two solid grounding cables to ground bracket as
shown in figure 3.2
3.2

INSTRUCTIONS CM336
For Technical Support: www.panduit.com/resources/install_maintain.asp
Step 4: Horizontal Cabling and Patch Panel Installation
4.4
TAK-TAPE
Location
4.2
PRBR3
Conduit
Knockout
4.1 Route horizontal cable from work area to the enclosure by way
of conduit, raceway (TG-70 or T-70), or through the cable brea-
kouts on the back wall of enclosure. Use supplied edge grom-
met to protect cables from sharp metal edges of raceway
knockouts and cable breakouts. Be sure to allow enough slack
to route and terminate cable.
4.2 With Patch Panel Bracket in up the position, install patch pan-
els (suggested PANDUIT Part No. CPPL24WBL sold sepa-
rately) along with PRBR3 bend radius posts to the front side of
the bracket. (See figure 4.2)
4.3 Rotate Patch Panel Bracket down by twisting latches to release
bracket. Terminate cables with MINI-COM GIGA-TX style jack
modules (sold separately). Snap modules into patch panels.
Punchdown Patch Panels can also be used.
4.4 Secure cables to bracket arm and back wall using supplied
TAK-TYS (See figure 4.4).
4.5 Rotate bracket into up position and rotate latches to hold
bracket in place (See figure 4.5).
Latches
4.5
TAK-TAPE
Location
5.1 Remove perforated panel
5.2 Identify the number of control systems to be mounted (e.g. access control,
lighting, HVAC, etc.).
Note: Do not exceed 50 watts without a fan or 180 watts with fan.
22.5
31.9
Step 5: Control System Mounting
Page 4 of 6

INSTRUCTIONS CM336
For Technical Support: www.panduit.com/resources/install_maintain.asp
5.3
5.4
5.5
Page 5 of 6
5.3 Determine physical space required on perforated panel for each system.(i.e physically lay out control systems on perforated panel).
5.4 Use panel duct (H2x2LG3) to segregate individual control systems. Cut duct to size and secure to perforated panel..
5.5 Secure all controls to perforated panel.

INSTRUCTIONS CM336
For instuctions in Local Languages
and Technical Support:
www.panduit.com/resources/install_maintain.asp
E-mail:
[email protected]om
Fax:
[phone]
www.panduit.com
To Wireless Antennas
Bulkhead
Cable
RS485
To RS485
connecto
r
located
on patch
panel
Page 6 of 6
Step 6: Optional Fan Installation (if required, sold separately)
6.1 Break out vent space on bottom of enclosure.
6.2 Place fan over opening. Line up the bottom fan
cover to the outside of enclosure and screw
into place.
6.3 Line up top fan cover and screw into place.
6.4 Determine the length of the power cord that is
desired. Strip back the insulation on the cord
and terminate to the plug.
6.5 Attach the power cord. The fan can be plugged
into an Uninterruptable Power Supply (UPS) or
the electrical box inside the enclosure.
Break out
vent space
SYSTEM #1
SYSTEM #2
SYSTEM #3
SYSTEM #4
5.6 5.7
5.6 Wire individual control systems using panel duct as
cable management pathway.
Note: Follow NEC guidelines and/or local codes as
required.
5.7 Reattach perforated panel. Route and attach wireless antenna
bulkhead cables as shown.
5.8 Terminate device cables from perforated panel to corresponding patch panel connector or external system.
Note: For steps 5-8, make sure to employ appropriate grounding practices to ensure personal safety, as well as, to protect
sensitive electronic equipment.
5.9Energize system.
TERMINAL
BLOCK