Panduit Atlona AT-HDR-EX-70C-KIT User manual

11
WARNING''
Use only BLUE colored ports when
connecting HDBaseT PoE devices.
PoE
Any other color may cause damage,
resulting in loss of warranty covera e
~' '
0 0 0 0 0 (, ,
□ ~D ea cacaca c:3 ~ ~- fi:j ~,
--- ·- -- ---

1
Installation Guide
AT-HDR-EX-70C-KIT
4K HDR HDMI Over HDBaseT TX/RX Kit
AT-HDR-EX-70C-KIT
The Atlona AT-HDR-EX-70C-KIT is an HDBaseT transmitter/receiver kit for high dynamic range
(HDR) formats. The kit is HDCP 2.2 compliant and supports 4K/UHD video @ 60 Hz with 4:4:4
chroma sampling, as well as HDMI data rates up to 18 Gbps. The HDR-EX-70C-KIT provides
transmission of HDMI, as well as bidirectional IR and RS-232 control signals up to 230 feet
(70 meters) for 1080p video, and up to 130 feet (40 meters) for 4K HDR over CAT6a/7 cable.
This extender kit features visually lossless compression with no latency to enable HDR and
4K/60 4:4:4 video signal extension over HDBaseT. For additional integration convenience, the
transmitter remotely powers the receiver through Power over Ethernet (PoE). The HDR-EX-70C-
KIT delivers a cost-eective solution for HDMI and control signal extension, and includes surface
mounting hardware for discrete installation.
IMPORTANT: Visit http://www.atlona.com/product/AT-HDR-EX-70C-KIT for the latest
rmware updates and Installation Guide.
1 x AT-HDR-EX-70C-TX
1 x AT-HDR-EX-70C-RX
4 x Mounting brackets
8 x Mounting screws
1 x 48V DC power supply
1 x IR emitter
1 x 2-pin captive screw connector
2 x 3-pin captive screw connector
1 x 4-pin captive screw connector
1 x 5-pin captive screw connector
1 x Installation Guide
Package Contents

2
Installation Guide
AT-HDR-EX-70C-KIT
AT-HDR-EX-70C-RX
POWER
LINKFW
RS-232
RX TX SS
P
HDBaseT IN HDMI OUT
IR OUT
IR IN
DC 48V
-
+
RS-232
RX TX SS
HDBaseT OUT HDMI IN
IR OUTIR IN
AT-HDR-EX-70C-TX
POWER
LINKTEST UTILITY
1. LINK
2. FW
3. TEST
4. 5V LOCK
Panel Descriptions
1 TEST
Quick and easy test for cables. Use the
button to start the test and the LED to
determine pass or fail.
2 UTILITY
Connect a mini-USB to USB-A cable from
this port to a computer for updating and
testing. Rotate the dial to set the unit into
dierent modes.
3 POWER and LINK LEDs
The power LED will illuminate green when
receiving power. The link LED will glow
yellow when signal is being sent/received
between the transmitter and the receiver.
4 DC 48V
Connect the included power supply to this
port.
5 RS-232
Bidirectional control port, used for pass
through of commands to or from the
receiver.
6 IR
Connect a 3rd party controller to the IR IN
port or an IR emitter to the IR OUT port.
7 HDBaseT OUT
Connect an HDBaseT cable from this port
to the HDBaseT IN port on the receiver.
8 HDMI IN
Connect an HDMI cable from a source to
this port. e.g. HDR BluRay Player
9 FW
Connect a mini-USB to USB-A type cable
from this port to a computer, to update
the rmware.
10 POWER and LINK LEDs
The power LED will illuminate green when
receiving power. The link LED will glow
yellow when signal is being sent/received
between the transmitter and the receiver.
11 RS-232
Bidirectional control port, used for pass
through of commands to or from the
receiver.
12 IR
Connect an IR receiver to the IR IN port or
an IR emitter to the IR OUT port.
13 HDBaseT IN
Connect an HDBaseT cable from this
port to the HDBaseT OUT port on the
transmitter.
14 HDMI OUT
Connect an HDMI cable from this port to
an HDMI display.
11
5 6 7 8 12 14
13
4
10
39 21

3
Installation Guide
AT-HDR-EX-70C-KIT
Pin out will be determined by the
RS-232 cable and connect as
RX (receive), TX (transmit) and
(Ground).
A 3-pin captive screw connector for RS-232 has been included.
Two captive screw connectors for IR have been included. A 4-pin connector for the transmitter
and a 3-pin connector for the receiver.
IR IN is connected by a power, ground, and signal
wire. Use a 12V IR receiver with it (e.g. AT-IR-CS-RX
purchasable through atlona.com).
IR IN is connected by a ground and signal wire. Use
with 3rd party control systems. For easy termination,
Atlona recommends using the 2 meter IR cable AT-LC-
CS-IR-2M (purchasable through atlona.com).
IR OUT is connected by a ground and signal wire.
Use the included IR emitter with this port.
IR OUT is connected by a ground and signal wire.
Use the included IR emitter with this port.
RS-232
IR
IR IN IR OUT
GND S
S
P
GND RX TX
GNDRX TX
IR IN IR OUT
GND S
S
The AT-HDR-EX-70C-KIT includes two mounting brackets and four mounting screws each, which
can be used to attach the units to any at surface.
1. Position one of the mounting brackets,
as shown below, aligning the holes on
the side of the enclosure with one set of
holes on the mounting bracket.
2. Use the enclosure screws to secure the
mounting bracket to the enclosure.
3. Repeat the above steps to attach
the second mounting bracket to the
opposite side of the unit.
Mounting Instructions
FW
AT-HDR-EX-70C-RX
POWER
LINK
Included screws

4
Installation Guide
AT-HDR-EX-70C-KIT
4. Mount the unit using the oval-shaped holes, on each mounting bracket. If using a drywall
surface, a #6 drywall screw is recommended.
NOTE: Mounting brackets can also be inverted
to mount the unit under a table or other at
surface.
FW
AT-HDR-EX-70C-RX
POWER
LINK
1. Connect an HDR source to the HDMI IN port on the transmitter.
2. Connect an HDR display to the HDMI OUT port on the receiver.
3. Connect an HDBaseT cable, from the HDBaseT OUT port on the transmitter, to the
HDBaseT IN port on the receiver.
4. *Optional* Connect a 3rd party controller to the transmitter using either the 3-pin RS-232
or the 2-pin IR IN ports.
5. *Optional* Connect an IR receiver to the IR IN port of the receiver.
6. *Optional* Connect an IR emitter to the IR OUT port of the transmitter or receiver.
7. Connect the included 48V power supply into the transmitter.
8. Connect power supply to an AC outlet.
Installation
Refer to the tables below for recommended cabling when using Altona products with HDBaseT.
The green bars indicate the signal quality when using each type of cable. Higher-quality signals
are represented by more bars.
Cable Recommendation Guidelines
Core Shielding CAT5e CAT6 CAT6a CAT7
Solid UTP (unshielded) N/A
STP (shielded)
Performance Rating (MHz) 350 500 600 800
*Atlona recommends TIA/EIA 568-B termination for optimal performance.
Cable* Max. Distance @ 4K Max. Distance @ 1080p
CAT5e / CAT6 115 feet (35 meters) 200 feet (60 meters)
CAT6a / CAT7 130 feet (40 meters) 230 feet (70 meters)
IMPORTANT: Stranded or patch cables are not recommended due to performance
issues.

5
Installation Guide
AT-HDR-EX-70C-KIT
Connection Diagram
DC5V HDBaseTIN HDMIOUT
Video
Video
Video
Control
Control
AT-HDR-EX-70C-TX
AT-HDR-EX-70C-RX
AT-JUNO-451
Automation Control System
1 2 3 4
HDMIIN HDMIOUT OPTICAL
AT-JUNO-451
RS-232 IR IN LAN DC5V
TX S
RX
Video
HDBaseT
Video
Set-Top Box
HDR Blu-ray Player
Media player
4
media4
SET-TOPBOX
OK
224
2
COM
NC
NO
COM
NC
NO
COM
NC
NO
COM
NC
NO
+12V
SIG
GND
+12V
SIG
GND
+12V
SIG
GND
+12V
SIG
GND
1
COMPONENT
HDMI
1
2
3
4
5
6
SERIAL1
IROUT SERIAL2
L
R
DIGITAL
COAXOUT
AUDIOOUT AUDIOIN ETHERNET
2 3 4
VIDEOOUT
48VDC
FACTORY
RESET
DC48V
-
+
RS-232
RX TX SS
HDBaseTOUT HDMI IN
IROUT
IRIN
AT-HDR-EX-70C-TX
POWER
LINKTEST UTILITY
1.LINK
2.FW
3.TEST
4.5V LOCK
HDR UHD/HD Display
AT-HDR-EX-70C-RX
POWER
LINKFW
RS-232
RX TX SS
P
HDBaseTOUT HDMI IN
IROUT
IRIN
TEST
The HDR-EX-70C-TX has the ability to test the HDBaseT cable quality through the front panel.
Press the test button on the front panel of the transmitter to start the test.
Button:
• Blue Blinking: The test is running properly.
• Red Light: There is no signal for the test to check.
LED:
• No Light: There is no HDBaseT cable plugged in.
• Blinking: There is no HDBaseT signal coming through.
• Green: The HDBaseT cable is good.
• Yellow: One or two HDBaseT pairs are not working, re-terminate
the cable.
• Red: Multiple pairs are not working. Re-terminate the cable and if
the LED turns yellow or red again, replace the cable.
DC 48V
-
+
RS-232
RX TX SS
HDBaseT OUT HDMI IN IR OUTIR IN
AT-HDR-EX-70C-TX
POWER
LINK
TEST
UTILITY
1. LINK
2. FW
3. TEST
4. 5V LOCK

6
Installation Guide
AT-HDR-EX-70C-KIT
Mode 1: Link
This is the default position of the dial and puts the unit into normal operation.
Mode 2: FW
This mode sets the transmitter into rmware updating mode. View Firmware Updating
instructions on the next page for manual updating.
DC 48V
-
+
RS-232
RX TX SS
HDBaseT OUT HDMI IN IR OUTIR IN
AT-HDR-EX-70C-TX
POWER
LINKTEST
UTILITY
1. LINK
2. FW
3. TEST
4. 5V LOCK
UTILITY
The utility port and dial are used for updating rmware and 5V
lock. Use the Dial to switch between modes.
Mode 3: TEST
Not used. Refer to the TEST button procedure, on page 5.
Mode 4: 5V Lock
This mode sets the +5V and the HPD signal of the transmitter and receiver to high. This allows
the source and display to have a consistent connection, even if there are issues with the source
and display signals.

7
Installation Guide
AT-HDR-EX-70C-KIT
Updating Firmware
1. Download the rmware .zip le from the rmware tab located at http://www.atlona.com/
AT-HDR-EX-70C-KIT.
2. Extract the rmware, from the archive le, to the Windows desktop or other folder.
3. Make sure the included 48 V DC power supply is connected to the transmitter and that an
Ethernet cable is connected between the HDBaseT OUT and HDBaseT IN ports on the
transmitter and receiver, respectively.
Transmitter only:
a. Set the UTILITY dial to 2.
b. Disconnect the 48 V DC power supply from the transmitter.
c. Connect a mini-USB to USB-A cable from the UTILITY port, on the transmitter, to the
computer with the rmware le.
d. Reconnect the power supply to the transmitter. The USB Drive folder should be
displayed after a few seconds. If the folder is not displayed select the USB drive from
Windows Explorer.
e. Go to step 4.
Receiver only:
a. Disconnect the Ethernet cable from the HDBaseT IN port on the receiver.
b. Connect a mini-USB to USB-A cable from the FW port on the receiver, to the computer
with the rmware le.
c. Reconnect the Ethernet cable to the HDBaseT IN port on the receiver. The USB Drive
folder should be displayed after a few seconds. If the folder is not displayed select the
USB drive from Windows Explorer.
d. Go to step 4.
4. Delete all les from the USB Drive folder, if any are present.
5. Drag and drop the rmware le to the drive. While the rmware loads to the unit, the green
power LED on the front panel will ash.
6. Once the LED is solid green, disconnect the unit from the computer.
Transmitter only:
f. Set the UTILITY dial to 1to resume normal operation.
7. The rmware update process is complete.

8
Installation Guide
AT-HDR-EX-70C-KIT
Version 4
© 2019 Atlona Inc. All rights reserved. “Atlona” and the Atlona logo are registered trademarks of Atlona Inc. All other brand names and trademarks or registered
trademarks are the property of their respective owners. Pricing, specications and availability subject to change without notice. Actual products, product images, and
online product images may vary from images shown here.
Toll free US International
atlona.com •877.536.3976 •41.43.508.4321

@ ATL □ NA .
Atlona IR Emitter Cable for
POE Extenders
AT-JR-CS-TX
atlona.com Toll free: 1-877-536-3976
Local : 1-408-962-0515

~ ATLONA .
Placement
The IR emitter can be used in several positions around the controlled device. As long as the IR
receiving window is lined up with the emitted IR signal. ( See pictures below for possible placement options)
A red LED will flash to indicate the IR emitter is operational and transmitting.
~· !
~
When using the IR emitter in a rack, it is best to use the included IR cover to
avoid signal interference of the controlled device and possible interference to
other IR devices within the rack.
-- Signal ( S)
Ground(-½)
Max peak current: 1 00mA
Connection Diagram
AT - IR-CS-TX
---- !~-~=""'- ~ E~ r
~.A.TL.ON/'\.
ma 11•1•
AT-UHD-EX-70C-TX
~/'\.TLCJN/'\.
~
AT1J•IIHX-J01.-IX
-·
0
~ 0
A1 -Ul'Df1 ~~~II.I:
AT-IR - CS-RX
Receiver ( ( (
00000 0~0000000
0 gooog 000000
.Q.Q.900~000000
L~
AT-UHD-EX-70C-RX ~ ------+ ~_-_-_-_-_-_ - _-_-,---.,...-_-_-_-_ - _- ___ __j::::.J
* Designed for select Atlona products
** For warranty information see http://www.atlona.com/marketing/img/limited_warranty/
atlona.com
Toll free: 1-877-536-3976
Local : 1-408-962-0515

1
AT-HDR-EX-70C-KIT
with Control and PoE
HDMI over HDBaseT™ TX/RX
4K HDR
The Atlona AT-HDR-EX-70C-KIT is an HDBaseT transmitter/receiver kit for high dynamic range (HDR) formats.
The kit is HDCP 2.2 compliant and supports 4K/UHD video @ 60 Hz with 4:4:4 chroma sampling, as well as HDMI
data rates up to 18 Gbps. The HDR-EX-70C-KIT provides transmission of HDMI, as well as bidirectional IR and
RS-232 control signals up to 230 feet (70 meters) for 1080p video, and up to 130 feet (40 meters) for 4K HDR over
CAT6a/7 cable. This extender kit features visually lossless compression with no latency to enable HDR and 4K/60
4:4:4 video signal extension over HDBaseT. For additional integration convenience, the transmitter remotely powers
the receiver through Power over Ethernet (PoE). The HDR-EX-70C-KIT delivers a cost-eective solution for HDMI and
control signal extension, and includes surface mounting hardware for discreet installation.
The HDR-EX-70C-KIT is ideal for residential and commercial applications with the latest as well as emerging 4K/UHD
and HDR sources and displays. It is compatible with all video resolutions, audio formats, and color space formats
supported in the HDMI 2.0b specication, plus the ability to pass metadata for HDR content. The HDR-EX-70C-KIT
includes Atlona’s award-winning 10 year limited product warranty and customer support services, so that integrators
can specify, purchase, and install with condence.
Introduction
Applications
• Residential installations
The HDR-EX-70C-KIT is designed for AV systems with the latest UHD and HDR sources such as Ultra HD Blu-ray
players, plus compatible televisions and projectors.
• TV showrooms
The HDR-EX-70C-KIT can be used for reliable content transmission to televisions, to properly demonstrate the
quality and appeal of 4K and HDR programming.
• Professional AV applications
Atlona 4K HDR products are ideal for full-motion, highly detailed 4K graphics presentations for visualization,
3D renderings, simulations, and more.

2
AT-HDR-EX-70C-KIT
with Control and PoE
HDMI over HDBaseT™ TX/RX
4K HDR
Key Features
4K/UHD capability @ 60 Hz with 4:4:4 chroma sampling, plus support for HDR formats
• Compatibility with new and emerging 4K/UHD and HDR-capable sources and displays.
• Compatible with 4K HDR10 @ 60 Hz and Dolby® Vision™ @ 30 Hz
• Fully supports video resolutions, audio formats, and color space formats in the HDMI 2.0b specication.
HDCP 2.2 compliant
• Adheres to latest specication for High-bandwidth Digital Content Protection.
• Allows protected content stream to pass between devices.
HDBaseT extender kit for HDMI up to 230 feet (70 meters)
• Extends HDMI, power, and control up to 230 feet (70 meters) @ 1080p and 130 feet (40 meters) @ 4K HDR using
CAT6a/7 cable.
• Uses easy-to-integrate category cable for low-cost, reliable system installation.
Receiver powered by transmitter via PoE (Power over Ethernet)
• Power for receiver is supplied by transmitter over HDBaseT.
• Allows convenient receiver installation at a display or projector without the need for local AC power.
Extends RS-232, IR, and CEC control signals over HDBaseT
• Bidirectional extension of RS-232 and IR control signals.
• Eliminates multiple cable runs between source, control system, and display.
Visually lossless compression
• Enables HDBaseT transmission of HDMI up to 18 Gbps using extremely light video compression with no latency.
Innovative signal extension solution delivers very high, pristine image quality.
Multi-channel audio compliant
• Supports PCM, Dolby® Digital, Dolby Digital Plus™, Dolby TrueHD, Dolby Atmos®, DTS® Digital Surround™,
DTS-HD Master Audio™, and DTS:X®.
• Allows any multi-channel audio stream to be used within a residential or professional audio system.
HDBaseT link status testing
• Free software utility available for testing integrity of the HDBaseT cable link between the transmitter and the
receiver.
• Provides real-time link status, plus detailed HDBaseT and HDMI signal information.
• Quick, easy verication or troubleshooting of RJ-45 termination or twisted pair cable quality.
• Test button and LED also available on the transmitter for checking HDBaseT link integrity.
Award-winning 10 year limited product warranty
• Ensures long-term product reliability and performance in residential and commercial systems.
• Specify, purchase, and install with condence.

3
AT-HDR-EX-70C-KIT
with Control and PoE
HDMI over HDBaseT™ TX/RX
4K HDR
Connection Diagram
DC5V HDBaseTIN HDMI OUT
Video
Video
Video
Control
Control
AT-HDR-EX-70C-TX
AT-HDR-EX-70C-RX
AT-JUNO-451
Automation Control System
1 2 3 4
HDMI IN HDMI OUT OPTICAL
AT-JUNO-451
RS-232 IRIN LAN DC 5V
TX S
RX
Video
HDBaseT
Video
Set-Top Box
UHD Blu-ray Player
Media Player
4
media4
SET-TOPBOX
OK
224
2
COM
NC
NO
COM
NC
NO
COM
NC
NO
COM
NC
NO
+12V
SIG
GND
+12V
SIG
GND
+12V
SIG
GND
+12V
SIG
GND
1
COMPONENT
HDMI
1
2
3
4
5
6
SERIAL1
IROUT SERIAL2
L
R
DIGITAL
COAXOUT
AUDIOOUT AUDIO IN ETHERNET
2 3 4
VIDEOOUT
48VDC
FACTORY
RESET
DC 48V
-
+
RS-232
RX TX SS
HDBaseT OUT HDMI IN
IR OUT
IR IN
AT-HDR-EX-70C-TX
POWER
LINKTEST UTILITY
1. LINK
2. FW
3. TEST
4. 5V LOCK
UHD Display
AT-HDR-EX-70C-RX
POWER
LINKFW
RS-232
RX TX SS
P
HDBaseT OUT HDMI IN
IR OUT
IR IN

© 2017 Atlona Inc. All rights reserved. “Atlona” and the Atlona logo are registered trademarks of Atlona Inc. All other brand names and trademarks or registered trademarks are the property of their respective owners. Pricing, specications and availability
subject to change without notice. Actual products, product images, and online product images may vary from images shown here.
4
atlona.com • 408.962.0515 • 877.536.3976
with Control and PoE
HDMI over HDBaseT™ TX/RX
4K HDR
Specications
Video
UHD/HD/SD 4096×2160@24/25/30/50/60Hz, 3840×2160@24/25/30/50/60Hz, 2048x1080p, [email protected]/24/25/29.
97/30/50/59.94/60Hz, 1080i@50/59.94/60Hz, 720p@50/59.94/60Hz, 576p, 576i, 480p, 480i
VESA 2560×2048, 2560×1600, 2048×1536, 1920×1200, 1680×1050, 1600×1200, 1600×900, 1440×900,
1400×1050, 1366×768, 1360×768, 1280×1024, 1280×800 1280×768, 1152×768, 1024×768, 800×600,
640×480
Color Space YUV, RGB
Chroma Subsampling 4:4:4, 4:2:2, 4:2:0
Color Depth 8-bit, 10-bit, 12-bit
HDR 4K HDR10 @ 60 Hz and Dolby® Vision™ @ 30 Hz
Audio
Formats PCM 2Ch, LPCM 5.1, LPCM 7.1, Dolby® Digital, DTS 5.1, Dolby Digital Plus™, Dolby TrueHD, DTS-HD
Master Audio™, Dolby Atmos®, DTS:X®
Sample Rate 32 kHz, 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz, 192 kHz
Bit Rate 24-bit (max.)
Resolution / Distance 4K/UHD - Feet / Meters 1080p - Feet / Meters
HDMI 15 5 30 10
CAT5e/6 115 35 200 60
CAT-6a / CAT-7 130 40 230 70
Signal
Bandwidth 18 Gbps
CEC Compliant
HDCP 2.2
Temperature Fahrenheit Celsius
Operating 32 to 122 0 to 50
Storage -4 to 140 -20 to 60
Humidity (RH) 20% to 90%, non-condensing
Power
Consumption 13 W
Input 100 - 240 V AC, 50/60 Hz
Supply 48 V DC, 0.83 A
Dimensions Inches Millimeters
H x W x D (Transmitter / Receiver) 1.02 x 4.29 x 5.00 26 x 109 x 127
Weight Pounds Kilograms
Device 0.85 (Transmitter), 0.86 (Receiver) 0.39 (Transmitter), 0.392 (Receiver)
Certication
Device CE, FCC
Power Supply CE, FCC, cULus, RoHS, CCC, RCM

~TLCJN~ e
Connecting Tech n ology
Did you know, many questions can be answered using our online
technical support website and internal knowledge database?
Technical Support website: www.atlona.com/tech-support
U.S. Technical Support Hours:
U.S. Technical Support Phone Numbers:
Monday-Friday: 5am - 5pm (PST)
Weekends and Holidays: 7am - 4pm (PST) Toll Free:
[phone]
Chat available from : 5am - 5pm {PST) weekdays only International:
+1 (408) 962 - 0515 ext. 1
International Technical Support Hours: International Technical Support Phone Numbers:
Monday -Friday: 8am - 5pm {UTC + 1: 00)
Europe Support Center: [phone] (UTC + 1: 00)
{No Intl weekend support offered -U .S. Support Available For an updated directory
of all International Atlona Support Centers,
from 7am - 4pm Sat -Sun) please
visit: www.atlona .com/tech-support