ParaBody 777101 User manual

SYSTEM
t
WA!RNLNG:
AReadandfollowall directions
¯ for e, ach~teptoinsureproper
assemblyof thi~procluct.
CLASS H ’.
PART# 70174(11
USER’ S GUIDE
1"qersion: 777101
Revision:02/02/01

TABLE OF CONTENTS
Safeb,Statement............. -~
@eneralNotes.................. ~
ToolsRequired................ 3
Layout..................... 4
Partslist .......................... 5
AssemblyInstructions ..... 6-23
GeneralMaintenance....... 24
WarrantyStatement.......... :!5
ProductServices.............. 26
Insert-Registration Card
.. [ IMPORTANT
SAFETY
THEREIS A RISK ASSUMEDBY INDIVIDUALSWHOUSETHIS TYPEOF
EQUIPMENT.TOMINIMIZERISK FOLLOWTHESERULI=S,!
1. Beforeusing,readall thewarningsandinstructions
ontheuseof this machine.Useonlyfor intended
exercise. DONOTmodifythe machine.
2. Obtaina medicalexambeforebeginningany
exerciseprogram.
3: Keepbodyandclothingfreeof all movingobjects.
4. Inspectthemachinebeforeuse.DONOTuseit if it
appearsdamaged.DONOTattemptto fix a brokenor
jammedmachine.Notify your authorizedParaBody
dealerbeforeuseandhaverepairs madeby an
authorizedservicetechnician.
5. Becertainthat weigl~tpinis completelyinserted.
Useonlythepin providedbythe manufacturer.If
unsure,call yourauthorizedParaBodydealer.
6. Neverpinthe weightsor propplate into anelevated
position. DONOTusethemachinei’! foundin this
condition.DONOTattemptto fix. N~tify your
authorizedParaBodydealer.
7. Inspectcablesandtheir connectionsb~foreusing
machine.Payparticularattentionto the cableends.
DONOTattemptto fix. Notify yourauthorized
ParaBodydealer beforeuseandhaverepairs madeby
anauthorizedservicetechnician.
8. Makesureall springloadedpull pinsarefully
engagedin theadjustmentpositionandfully tighten
thumbscrewbeforeuse.
9. Childrenmustnot beallowedne~rthis machine.
Supervi9eteenagers.
NOTE: In a continualeffort to improveour productslsp-ecificatio~as are subject to change
©2001Life Fimess, a division of BrmaswickCorporation. All rights reserved.
ParaBodyis a trademarkof B~n,mswickCorporation
ww~w.parabody.com 2

ORTANTNOTF_,~-~
Please note:
* That3kyoufor put-chasing the ParaBody777GymSystem.Please read these instructions
thoroughlyandkeepthemforfutm’e reference.-
*Thisproductmustbeassembledona fiat,levelsurfacetoassureitsproperfhnction.
* Donot securely tighten, any frameconnectionsuntil the entire frmnehavebeenassembled
m~lessotherwisespecified.
* Rubbermallet or hammer
.* 3/4" wrench
* 9/16" wrench
¯ * Ratchetwith3/4" and9/16" sockets
* 5/32" Allen wrench
* Adjustable wrench
* Tape measure
BOLT LENGT]I RULER:
~---1/2
o I

I Square
= I’X 1’.
Minimum Required Usable S~
Length
Width
Height
= 90inches(229cm)7’
=103inches.(262cm)8’
=84inches(213.5cm)
Dimensions Includin~
-a[)-
Length = 90inches(229cm)7’
Width = 130inches(330cm)10’ 10"

5
7
8
9
,0
2:
2~
2
,
9
3
PART#
70077
70076
70058
70014
70015
70017
70019
70056
70067
69408
69885
69954
69957
70082
70083
69947
6194601
;816501
7016902
’016901
~939202
69537
3221702
~978101
~108002
i987801
6987901
6988001
~988101
70121
DESCP,_LPTION
BASE
UPRIGHT
SEATADIUST
RIGHT Aydvl SUPPORT
LEFT ABM SUPPORT
RIG~’rAKM
LEFtARM
LEG PEDESTAL
PULLEYBRACI(-ET
p ULLEYP LATE
BASE PLATE
v.PULLEYPLATE
BOOMPULLEY PLATE
RIGHT BOOMPLATE
LEFf BOOMPLATE
PAD
ROLLER PAD
76" GUIDE ROD
14-1/2" SEWN HANDLE
7-I/2" SEWN HANDLE
WE1GHT PLATE
WEIGHT PLATEBUSHING I0 CT
HEAD PLATE
E-RING
WEIGHT STACII LABEL
WE1GHT PL ATE SHAFT
WEIGHT STACK PIN
cUSHION
WEIGHT CABLE
LEG cABLE
ARM CABLE
BOOM CABLE
WEIGHT STACIi SPACER
PARTS
5
2
2
2
15
1
1
1
1
1
9
]
LIST
PART#
3102503
6409101
3103302
3116201
3116101
6993701
6412001
I0~801
6416601
6145801
31054,01
3108901
6866801
6480301
6480302
6122702
6122701
6549301
3102924
3102807
102922
3221902
~102905
" 9
z102 17
6075906
3102906
3102930
3102804
3102802
3102501
6020601
70718
3102904
DESCPdPTION
3/4" FLAT
A_N~CLESTP~4P
SP~T COLL.~ ~2
3-112" P~LEY
4-1/2" p~.LEY
4-1/2" V-GRO0~ p~LEY
SP~N G PIN AS S:E~LY
SN~ L~
p~GL~E (Q~r
3 PRONG KNOB
ST~OCK
PLASTIC WA~R
1/2" ~ WAS~R
318" ~ 9116" ~G~
31B ~ 1-1116" ~IG~
31B ~ lIT ~ SP~C~
318" ~ 1" S~C~ .I
314 ~ 17" T~
31B~ I"314~’ ~O~T 4
31B ~O~ ~IG~T ~OCK
31B~ 2-314" ~O~T i,
2" ~O~ S~C~
31B~ 3-314" ~O~T I
12 L~¢ CHMN
3/8 X 4" BOLT
3/8 X 7" BOLT
1/2" LOW~IG]~ LOCK ~T
3/g" LOCK
3/8" FLAT
liT’ ~G~E BEING
FOOTPL~E
3/8 X 3" BOLT

3-314"
3/8 X3"
STEP 1: ..... .,- ," (57) andfour
¯ LOOSELYassemble two BASEPLATES(11)to the BASE(1) and the UPRIGHT(2) using four ~/8 X: ~/4
¯ "- s2 (63). See FIGURE
3/8 LOCI NUTS
¯Insert twotwo3/8 X9/16’: FLANGESPACERS(48) into the upperhole of the FRAME(2) as shown.
¯LOOSELYassemble the FOOTPLATE(66) to the FRAME(2) using one 3/8 X3" BOLT(67) and one 3/8": LOCKNUT(63)
shown in FIGUtLE1. -- 1/’~ "]
1 I I I I

FIGURE 2
~
TEP2: . ,, . ... .......
Insert two WEIGHTPLATEBUSHINGS(22) into each of the fifteen WEIGHTPLATES(21) as shownin FI[GURE
FIGURE3 ~S~howll
~
TEP 3: ’
Slide the WEIGHTPLATESHAFT(26) tlLru the hole in the t-I~.AD PLATE(23).,nnd lock in place using one E-RING
in FIGURE 3 .... ., 7

FIGURE 4
STEP4:
¯Insert two GUIDERODS(lg) into the BASE(1) as shownon FIGURE4. (NOTE:Lubi-icate GUIDERODS(18) with
or teflon spray availabl6 at most hardware stores.)
¯ Slide two WEIGHTSTACKSPACERS(33), two 3/4" FLATWASI-IERS(34). and two WEIGHTSTACKCUSHIONS(28)
overtheGUIDEKODS(Ig).
¯ UsingEXTREIV~ECAI’OEslidea11fffleenWEIGHTPLATES(2
I)
downovertheGUIDERODS(18)on to theWEIGHTSTACK
¯ CUSHIONS(28).Makesurethatth~WEIGHTPLATES(2I)are.allfa¢ingasshown.
Slide the head plate assemblydowno’s, or the GUIDERODS(18) onto the weight stack.
Slide two SHAFTcoLLARS(36) over the GUIDERODS(18) as shown in FIGURE
k_--J- ¯8

FIGURE 5 /shown
STEP5:
,Swingthe GUIDERODS(lg) into the guide rod bushingsin eachof the RIGHTandLEFTUPRIGHTPLAX~S(14 &15)
in FIGURE5. " ’ " 15) to theUPRIGHT(2) using three 3/g X3-3/4" BOLTS(57)
¯ LOOSELYassemble theRIGI-IT andLEPTUPRIGHTPLATES(14
andfllree 3/g" LOCI:NUTS(63). See FIGURE5.
¯ Slide the SI-IAFTCOLLA-RS(36) to the top of the GLUDERODS(lg) and tighten set screwsas shownin FIGURE
FIGURE 6
/,:
%-.13,~,G "~ " " .
~.~ (S6).four
STEP6:
¯LOOSELYassemble the ~GHTand LE~,~ S~PORTS(4 &5) to the BASE(1) using four 2/g X3-3/4" BOLTS
3/8" ~ATWAs~RS(64), ~nd four 3/8" LOCK~TS(63). See FIG~
Appl~’ ~IGHTSTACKL.~ELS(25) to the ~IGHTPLATES(21) ~s shownin FIG~
¯9

FIGURE 7 L
;TEP 7: .
¯LOOSELYassemble the 1LIGHTand LEFTAKMS(6 & 7) to the UPRIGHT(2) mad the RIGHTand LEFTARMSUPPORTS
&5) using two 3/8 X 4" BOLTS(60), four 3/8" FLATWASHERS(64), and two3/8" LOWHEIGHTLOCKNUTS(54).
FIGISRE7.
FIGURE8
STEP8:
¯ SECURELYassembleoneSEATPAD(16)to theSEATAD JUST(3)usingtwo3/8X 2-3/4"BOLTS(55)andtwo3/8"WASHERS
(64). See FIGURE
012 . 3. . .4 56
2 . 3 . .4. s, I t J
10

~IGURE 9
S.TEP9:¯ ’ Securely assemble one SPRINGPINAssEMBLY(40) and one ~ PRONGKNOB(43) to the FRONTIIPPJGHT(2) as
~ . Applye~ghtpAp,AGLIDES(42) to the INSIDEof the tube on the LTPR.IGHT(2) andon the OUTSIDEof the SEATAD3UST
as showr.. ¯ SEATADXJSTASSEMBLYinto the UPRIGHT(2) as shown.The SEATheight ambe adjusted using the
¯ CAREFULLYiasert the
SPRINGPIN(40) and can be secured with the .3 PRONGICNOB(43).
STEP10:
¯ InserttwoI/2"FLANGEBEARINGS(65)intothetheLEGpEDESTAL(~)as showninFIGURE
¯Assemblethe LEGPEDESTAL(~) to th~ UPRIGHT(2) using two RHCAPS(47). one 1/2 X4" BOUF(SB): two
WASHERS(46). and one liT’ LOWHE1GHTLOCKNUT(62). (Note: Tighten this connection enoughto remove
p|ay yet allow the LEGPEDESTALto rotate freely.)
¯.. 11

FIGURE Ii
;TEP 11: .
¯Assemble two V-PULLEYPLATES(12) and two 4’1/2" V-GROOVEPULLEYS(39) to the UPRIGHT(2) ~sing two3/g X 2-3/4".
BOLTS(55). See FIGIYILE11.
STEP~2:
¯ Assembletwo BOOMp~LEYPLATES(13) and three 3-1/2" P~LEYS(37) to the ~OOMPLATES(].4 & 15) using o~e
7" BOLT(61). two 3/g X 1/2" SPACEKS(50), two 3/8 X 1" SPACEKS(51) and one3/8" LOC~~JT(63) . SeeF]G~.

STEP14:
¯ Assemble the WEIGHTSTACI4PIN (27) to the
WEIGHTSTACKSHAFT(26)as shownin
FIGURE14.
¯Screwfl~¢ long threaded end of the WEIGHT
STACKCABLE(29) into fl~e end offl~eWEIGHT
PLATESHAFT(26).SeeFIGURE14.
¯ Routefl~eWEIGHTSTACKCABLE(29)around.
thepull~ysinfl~eBOOMPLATES(14& 15)
shown in FIGURE14. (NOTE:Nlake sure the
--.--- cable runs in the ~-ooves of the pulleys.)
¯ AssembIe two PULLEYPLATES(10) around one
3-1/2" pULLEY(37) using one 3/g X 1-3/4"
BOLT(53) and one 3/8" LOCI4NUT(63)
shown in FIGURE14. (Note: Loop the CABLE
around the PULLEYprior to assembling the
pULLEY PLATES.)
FIGURE 14

FIGURE 15
;,TEP 15: .
¯Assembleone3-I12"PULLEY(37)to theBOOMPLATES(14& 15)using,one318X 3-314"BOLT(57),two31gX I"SPACERS
(5 I) andone31g"LOCKNUT(63).SeeFIGURE15.(Note:LooptheWEIG~ITSTACKCABLEaroundthePULLEYprior
assembling to the BOOMPLATES.)
¯Screwtheshortthreaded6ndoftheWEIGHTSTACKCABLE(29)intotheendofthePULLEYBRACICE’F(9).SeeFIGLrRB
3/8X2-3/4"~..
FIGURE16 /,. ......
STEP16:
¯ ¯ Rou-te the BOOMCABLE(32) over the V-GROOVEPULLEY(39) and the 3-1/2" PULLEY(37) on the LEFTBOOM
(15) and over the 3-1/2" PULLEY(37) on the RIGHTBOOMPLATE(14) and over the V-GROOVEp0"LLEY(39) as
STEP16.
¯SECIJRELN
~ assemble two 2" NYLONSPACERS(56) to the V-PULLEYPLATES(12) and the BOOMPLATES(14 &15)
two 3/8 X 2-3/4" BOLTS(55) and two 3/8" LOCKNUTS(63). See FIGURE
usin~ one 3/8 X1-3/4" BOLT(53) and one 3/8 LOCK
¯ Assemble one _~-1/- PULLEY(37) to the PULLEYBRACKET(9)
NUT(63) (Note: Loop the BOOMCABLEaround the PULLEYprlo," to assembling the PULL!;Y BRACKET.)
14 --

FIGURE 17
3/8X3-3/4"
STEP17:
Securely assemble the ball end of the LEGCABLE(30) and one 3-1/2" PULLEY(37) to the LEGPEDESTAL(g) using two
3-3/4" BOLTS(57), two 3/g" X 1-1]16" FLANGESPACERS(49), two 3/8" WASHERS(64), a~d two 3/g" LOCI,2NUTS
(NOTE:The LEGCABLE(91) must be routed over the retaining bolt as shown in FIGUILF,17.)
Securely assemble one 3-1/2" PL
TLLE~r
(37) to the UPtLIGHT(2) using one 3/8 X 3" BOLT(67) and one 3/8" LOCI,LNUT
(NOTE:The LEGCABLE(91) must be routed over the retainingbolt as shown in FIGUPGg17.)
Assembleone 3-1/2" PULLEY(37) to the BASEPLATES(11) using one 3/8 X 3-3/4" BOLT(57),two 3/8 X 1" SPACERS(51)
one 3/8" LOCI(NUT(63). See FIGURE17 .(Note: Loop the LEGCABLE(30) .around the PULLEYprior to assembling
PULLEYto the BASEPLATES.)

STEPI~:
¯Assembleone 3-1/2" PULLEY(37) to the
PLrLLEYPLATES(10) using one 3/8 X
3/4:’ BOLT(53) and one 3/8" LOCKNUT
(63) as shownin FIGURE18. (Note:
Loop lhe CABLEaround the PULLEY
prior lo assembling the prsLLEY
PLATES.)
FIGURE19 /
/:
3/gX3-3/4"
/"’’....: ’ ii" / I:/ "i~"i.. .’" .,.0.~/ ..... -- ~.
.,:-........L ’" ..... t/<--.:..I" ,.’.....,/........
-
:./’-.. "’--..."-~..., .... ." , ~f
~e, ,rr, .-’......
’i:~.’:.....
"" ’’> " ’. ’ ~". "t~:.-......," ii"
’~::
..........’":"
/ !\~, ~ ...... .-
STEP 19: ..... " ~’
¯ Assembleone 3-1/2" PULLEY(37) to the BASEPLATES(11) using one 3/8 X :-o/4 BOLT(-~7). two ~/8 X 1’: SPACERS(51)
one 3/8" LOCKNUT(63). See FIGURE19.(Note: Loop the LEGCABLE(30) around the PULLEYprior to assembling
BASE PLATES.)
. Screw the threaded end of the LEOCABLE(30) into the end of the PULLEYBRACKET(9). See FIGURE

FIGURE
I//
I,I
STEP20:
¯Rometh~ARIvlCABLE(3I) throughtheLEFTARM(?)as showninFIGURE
" sinone3/gX o-3/~"BOLT(55)ando~.=3/8"LOCI~~T(63).
", ~ [~~T ~ S~PORT (~) u - A~ s~PORT.)
¯C~LE~roundt~ie pULLEYprior~o assembhn~~he LEFT ~
Ass~mbI~o~ V-P~LE~(o9)
S~ FIG~ 20. (Note: ~oop ’ ’" "
¯SEc~LYa~emb1~one 2" ~ON SPACER(56) to th~ LEFT ~ S~PORT(5) u~ingon~ 3/8 X ~-314"BOLT (55)
on= 318" LOCK ~T (63). S~= ~G~ 20.
¯ "Assumablefl~~LEFT~ (7)to ~~ LEFT~ S~POKT(5) usingone 3/gX 2-0/4BOLT(55)~d on~ 318"LOCK~T
S~FIG~20. (No~e:~ake sure~he A~ C~LE runs in FRONTof ~he boltas sho~’nL)
, "BOLT(55).m,o318X liT’SPACERS(50)and
¯ Assembleone4-I/2"p~LEY(38)to theLEFT~ (7)usingone3/~X 2-3/4
3/8"LOCK ~T (63).See FIGU~20. (No~e:Looplhe A~{ CABLEaround~he PULLEYprbr~o assemblingthe LEFT

FIGURE 21
/CABLE",,
STEP21:
¯Assembl¢two3-1/2" PULLEYS(37) to the BASEPLATES(11) using two3/8 X3-3/4" BOLTS(58), one ~./8 X1" SPACER
and two 3/8" LOCKNUTS(63). See FIGURE21.(Note: Loopthe ARMCABLE(31) around the PD~LLEYSprior to assem-
bling the PULLEYS.Leave a loop in the ~ CURLas shown!)
FIGURE 22
(
/ -
~TE 22:
¯Assemblyone3-I12’:PULLEY(37)tothePULLEYBRACKET(9)usingone318X 1-314’"BOLT(53)andone31g"
NUT(63)(Note:LooptheARMCABLE(31)aroundthePULLEYpriortoassemblingthePULLEYBP~ACKET.)
18

FIGURE23
, =-’+’+",+.+ . ". C.+."+- ¯
3/8 X 2-3/4" ~+~.+. ~ "" b’ + ..
/]-i .
]]
3/8X2-3/4"
ST~,P
¯ Route the A_PdvlCABLE(31) through the RIGHTARM(6) as shownin FIGURE
the RIGHTAP, M(6) using one 3/8 X2-3/4" BOLT(55), two 3/8 IK 112" SPACERS(50)
¯ Assemble one 4-1/2" PULLEY(38) (Note: Loop the ARlVlCABLEaround the PIILLEYp:fior to assembling the
one 3/8" LOCI(NUT(63). See FIGURE ¯one 3/8" LOCK
RIG]~T ARI~.)
¯Assembleone "v-PULLEY(39).to the RIGI-IT-ARMSUPPORT(4) using ush~g one 3/8 X 2-3/4" BOLT(55)
NUT(63). See FIGURE23. (Note: Loop the APGV[CABLEaround the PULLEYprior to assemb’.iing the RIGHTAPdVI
S~JPPORT.).
¯SECURELYassemble one 2" NYLONSPACER(56) to the RIGHTARMSUPPORT(4) using one 3]8 X. 2-3]4" BOLT(55)
one 3/8" LOCI(NL]T(63). See FIGURE
¯ Assemble the I~IGI-IT ~ (6) to the RIGHTARMSUPPORT(4) using one 3/8 X ,-~/~ BOLT(55) and one 3]8" LOCK
(63). See FIGURE20. (Note: Makesure the ARMCABLEruns in FRONTof the bolt as shown!,)

FIGURE
STEP~4:
¯ SECURELYtighten all loose frameconnections as shownin FIGURE24!
I 1/2 1