ParaBody 336101 User manual

336101
350104 LEG PRESS ADAPTERKIT
ASSEMBLY INSTRUCTIONS
SORT AND COUNT ALL PARTS BEFORE BEGINNING ASSEMBLY
ITEM NAME/DESCRIPTION
2.
3.
4.
5.
6.
7.
8.
3/8X2IN.BOLT......................................................................................................................................
3
3/8X3IN.BOLT...................................................................................................................................... 4
3/8IN.WASHER......................................................................................... ~.............................................
8
6
3/8IN.LOCKNUT.......................................................................................................................... ’.........
2-3/8IN.CABLERETAININGCLIP................................... ~..;...............................................................
2
27/8IN.CABLERETAININGCLIP...................................................................................................... 1
2IN.SQPARABODYCOVERCAP...................................................................................................... 2
2
3-1/2X1IN.PULLEY.............................................................................................................................
NOTE: BOLT LENGTHIS MEASUREDFROMTHE UNDERSIDEOF THE HEADOF THE BOLT.
IIIiiiiii
BOLT LENGTH
BOLTLENGTHRULER:
Part # 6638101 1Revision:06/03/96

NOTE: THE LEG PRESS ATTACHMENT(832101) MUST BE ASSEMBLEDBEFORE ASSEMBLING
TO THE PARABODY350. PLEASE ASSEMBLE THE LEG PRESS ATTACHMENTAT THIS
TE~IE USING THE 832 PRODUCTASSEMBLYINSTRUCTIONS.
Insert two (2) 2 SQ. IN. PAKABODYCOVERCAPS onto the BASECONNECTIONWELDMENT
shown on drawing.
Removemiddle 4-1/2 X I IN. PULLEY,3/8.X 1-3/4 IN. BOLT,and 3/8 IN. LOCK]xrUT from the 350
BASE.
3o Kemove the SECONDARY(LOWER)CABLEfrom the 350.
4. NOTE: The SECONDARY(LOWER)CABLEwill no longerbe needed.
oSECURELYassemble the BASECONNECTIONWELD1VIENTto the 832 using two (2) 3/8 X 3 IN.
BOLTS,four (4) 3/8 IN. WASHEILS,and two (2) 3/$ IN. LOCKNUTS.
LOOSELYassemble one {I) 4-112 X ) IN. PULLEY,from step 2, to the lower hole on th¢t right side
the BASECONNECTIONWELDMENTusing one (1) 3/8 x 2 IN. BOLT,one (1) 2-718 IN. CABLE
RETAININGCLIP, and one (I) 3/8 IN. LOCKNUT.
o
I0.
LOOSELYassemble one (1) 3-1/2 X1 IN. PULLEYto the upper hole on the left side ofl~e BASE
CONNECTIONWELDMENTusing one (1) 3/8 x 2 IN. BOLT, one (1) 2-3/8 IN. CABLERETAINING
CLIP, and one (I) 3/8 IN. LOCKNUT,
LOOSELYassemble one (1) 3-1/2 X1 IN. PULLEYto the middle pulley fiat of the 350 BASEusing one
(1) 3/8 x 2 IN. BOLT,one (1) 2-3/8 IN. CABLERETAININGCLIP, and one (1) 3/8 IN. I.,OCK
SECURELYattach the BASECONNECTIONWELDMENTand the 832 to the base of the 350 using
two(2) 3/8 X3 IN. BOLTS,four (4) 3/8 IN. WASHEKS,and two C2) 3/8 IN. LOCKNUT;S.
Following the cable routing diagram, thread the LEGPRESSCABLEfrom the SWIVELLOWROW
through the BASECONNECTIONWELDMENTand around the pulley in the 832. (The pulley, wheels,
and spacers mayneed to be temperately" removed) and to the ezra on the LEGCURL/EXT.
11. SECUREend of LEGPRESSCABLEto the cam using the hardware removed in step 3.
12. SECURELYtighten all pulley connections, making sure that the CABLERETAININGCLIPSare facing
the correct direction as shownin drawing.
13. If uponcompletionof assembly,the headplate does not sit on top of first weightplate or there is excess
slack in the cable system, refer to your 350 ASSEMBLYINSTKUCTIONS.(NOTE:Someslack in the
cable systemis neededto allow for pre-streteh adjustment in the 832 leg press.)
Part # 6638101 2Revision: 06/03/96