Parker Pneumatic PVLC10 User manual

Pneumatic Division
Richland, Michigan 49083
Phone:[phone]
Fax: [phone]
Pneumatic
Installation Instructions: V-382P
PVLB10 / PVLC10
Serial Bus Modules
ISSUED: June, 2001
Supersedes: None
NPR# 2047
PVLB10 / PVLC10 Serial Bus Modules
Installation Instructions

Parker Hannifin Corporation
Pneumatic Division North America
Richland, Michigan
Pneumatic
2
Contents
DeviceNet™ ................................................................................................................................ 3-4
PROFIBUS-DP®............................................................................................................................. 5
InterBus-S®..................................................................................................................................... 6
ASI®............................................................................................................................................. 7-8
PVLB10/ PVLC10 Serial Bus Modules V-382P
!
WARNING
To avoid unpredictable system behavior that can cause personal injury and property damage:
• Disconnect electrical supply (when necessary) before installation, servicing, or conversion.
• Disconnect air supply and depressurize all air lines connected to this product before installation, servicing, or
conversion.
• Operate within the manufacturer’s specified pressure, temperature, and other conditions listed in these instructions.
• Medium must be moisture-free if ambient temperature is below freezing.
• Service according to procedures listed in these instructions.
• Installation, service, and conversion of these products must be performed by knowledgeable personnel who
understand how pneumatic products are to be applied.
• After installation, servicing, or conversion, air and electrical supplies (when necessary) should be connected and
the product tested for proper function and leakage. If audible leakage is present, or the product does not operate
properly, do not put into use.
• Warnings and specifications on the product should not be covered by paint, etc. If masking is not possible,
contact your local representative for replacement labels.
!
WARNING
BEFORE SERVICING THIS UNIT!
Hazardous voltages and fluid pressures may be present. Disconnect all external power, BUS connections and air
supply prior to the servicing of this device.

Parker Hannifin Corporation
Pneumatic Division North America
Richland, Michigan
Pneumatic
3
DeviceNet
™
Technical Specifications
Bus Voltage ..................................................... 11 to 25 VDC
Bus Current ............................................................... 200mA
Maximum Current Per Output ................................... 350mA
Total Output Current ....................................................... 1A
Number of Outputs .......................................................... 16
Baud Rates ......................................................... 500 Kbaud
250 Kbaud
125 Kbaud
Degree of Protection ..................................................... IP65
Operating Temperature
60% Rating .......................... 0°C to 55°C (32°F to 130°F)
100% Rating ........................ 0°C to 40°C (32°F to 104°F)
External Power Supply .................................20.4 to 30 VDC
Data Rates
Baud Distance Drop Length
Rate Max Drop Cumulative
125 Kbaud 500m (1640 ft) 6m (20 ft) 156m (512 ft)
250 Kbaud 250m (820 ft) 6m (20 ft) 78m (256 ft)
500 Kbaud 100m (328 ft) 6m (20 ft) 39m (128 ft)
Note: This device transmits 2 bytes and receives 2 bytes.
The EDS file can be downloaded from our website
http://www.parker.com/pneumatic. Click on Solenoid / Air
Operated Valves and then click on PVLB10 or PVLC10 Valves
and finally click on Service / Maintenance.
PVLB10/ PVLC10 Serial Bus Modules V-382P
E STOP Feature*
Output power to the solenoids can be wired to allow the user
to turn the outputs off while allowing the communications to
remain on. This can be done by placing the user's
Emergency Stop Switch or other hard wired control contact
between Pin 3 and Pin 4. If this feature is not required, Pin 3
and Pin 4 should be wired together.
Pin 1
Pin 2
Pin 3
Pin 4
Pin 5
0 VDC
24 VDC
Gnd
User's Emergency Stop Switch or
other hard wired control contact.
Tie together if Emergency Stop
Switch is not required.
Power Connector
Bus Connector
Pin Function
1 Drain
2 V+ (24 VDC)
3 V- (0 VDC)
4 CAN_H
5 CAN_L
Power Connector
Pin Function Comment
1 0 VDC BUS POWER
2 24 VDC
3* Valve Power VALVE POWER
4* Valve Power
5 Ground
Recommended Bus and Power Connector (or equivalent):
Turck female Eurofast #B 8151-0
12345678
M12
Micro Bus Connector
(Male) Face View
M12
Micro POWER Connector
(Male) Face View
OFF
ON
Dip Switches
BUS
BUS
OUT
POWER
BA
ON
ERR

Parker Hannifin Corporation
Pneumatic Division North America
Richland, Michigan
Pneumatic
4
DeviceNet
™
Baud Rate Setting Through DIP Switches
Baud Rate 7 8
125 Kbaud OFF OFF
250 Kbaud ON OFF
500 Kbaud OFF ON
PVLB10/ PVLC10 Serial Bus Modules V-382P
Node Address Settings Through DIP
Switches
Node Address 1 2 3 4 5 6
0 Off Off Off Off Off Off
1 On Off Off Off Off Off
2 Off On Off Off Off Off
3 On On Off Off Off Off
4 Off Off On Off Off Off
5 On Off On Off Off Off
6 Off On On Off Off Off
7 On On On Off Off Off
8 Off Off Off On Off Off
9 On Off Off On Off Off
10 Off On Off On Off Off
11 On On Off On Off Off
12 Off Off On On Off Off
13 On Off On On Off Off
14 Off On On On Off Off
15 On On On On Off Off
16 Off Off Off Off On Off
17 On Off Off Off On Off
18 Off On Off Off On Off
19 On On Off Off On Off
20 Off Off On Off On Off
21 On Off On Off On Off
22 Off On On Off On Off
23 On On On Off On Off
24 Off Off Off On On Off
25 On Off Off On On Off
26 Off On Off On On Off
27 On On Off On On Off
28 Off Off On On On Off
29 On Off On On On Off
30 Off On On On On Off
31 On On On On On Off
Node Address 1 2 3 4 5 6
32 Off Off Off Off Off On
33 On Off Off Off Off On
34 Off On Off Off Off On
35 On On Off Off Off On
36 Off Off On Off Off On
37 On Off On Off Off On
38 Off On On Off Off On
39 On On On Off Off On
40 Off Off Off On Off On
41 On Off Off On Off On
42 Off On Off On Off On
43 On On Off On Off On
44 Off Off On On Off On
45 On Off On On Off On
46 Off On On On Off On
47 On On On On On On
48 Off Off Off Off On On
49 On Off Off Off On On
50 Off On Off Off On On
51 On On Off Off On On
52 Off Off On Off On On
53 On Off On Off On On
54 Off On On Off On On
55 On On On Off On On
56 Off Off Off On On On
57 On Off Off On On On
58 Off On Off On On On
59 On On Off On On On
60 Off Off On On On On
61 On Off On On On On
62 Off On On On On On
63 On On On On On On
Module Status Lights (LED's)
Indicator Description
Power-BUS SteadyGreen Normal
OFF No Power Applied to the BUS
Steady Green Normal
Power-Out OFF No Power Applied to the
Valves
BUS-BA Steady Green Normal
Flashing Green Configuration Problem
BUS-ERR OFF Normal
Steady Red BUS Error
BUS-ON Steady Green Normal
OFF No Power Applied to the BUS

Parker Hannifin Corporation
Pneumatic Division North America
Richland, Michigan
Pneumatic
5
Baud Rate Setting
This system incorporates an Auto-Baud detect feature,
eliminating the need to set switches.
PROFIBUS-DP
Bus-In Connector
Pin Function
1NC
2NC
3 A Line
4 B Line
5RTS
Bus-Out Connector
Pin Function
1 5V Pocket
2 0V Pocket
3 A Line
4 B Line
5RTS
PVLB10/ PVLC10 Serial Bus Modules V-382P
Technical Specifications
External Power Supply .................................20.4 to 30 VDC
Bus Current ............................................................... 200mA
Maximum Current Per Output ................................... 350mA
Total Output Current ....................................................... 1A
Number of Outputs .......................................................... 16
Baud Rates .................................... 9.6 Kbaud to 12 Mbaud
Degree of Protection ..................................................... IP65
Operating Temperature
60% Rating .......................... 0°C to 55°C (32°F to 130°F)
100% Rating ........................ 0°C to 40°C (32°F to 104°F)
Data I.D. Code .............................................................. 1000
Data Rates
Baud Rate Distance
9.6 Kbaud 9,600m (31,488ft)
19.2 Kbaud 9,600m (31,488ft)
93.75 Kbaud 9,600m (31,488ft)
187.5 Kbaud 8,000m (26,240ft)
500.0 Kbaud 4,000m (13,120ft)
1.5 Mbaud 500m (1,640ft)
12.0 Mbaud 500m (1,640ft)
Note: This device transmits 2 bytes and receives 2 bytes.
The EDS file can be downloaded from our website
http://www.parker.com/pneumatic. Click on Solenoid / Air
Operated Valves and then click on PVLB10 or PVLC10 Valves
and finally click on Service / Maintenance.
Power Connector
Pin Function Comment
1 0 VDC BUS POWER
2 24 VDC
3* Valve Power VALVE POWER
4* Valve Power
5 Ground
Recommended Bus and Power Connector (or equivalent):
Turck female Eurofast #B 8151-0
Turck male Eurofast #BS 8151-0
Module Status Lights (LED's)
Indicator Description
Power-BUS SteadyGreen Normal
OFF No Power Applied
Steady Green Normal
Power-Out OFF
No Power Applied to the Valves
BUS-BA Steady Green Normal
OFF Configuration Problem
BUS-ERR OFF Normal
Steady Red BUS Error
BUS-ON Steady Green Normal
OFF No Power Applied
Node Address Setting Through Rotary Switches
E STOP Feature*
Output power to the solenoids can be wired to allow the user
to turn the outputs off while allowing the communications to
remain on. This can be done by placing the user's
Emergency Stop Switch or other hard wired control contact
between Pin 3 and Pin 4. If this feature is not required, Pin 3
and Pin 4 should be wired together.
Pin 1
Pin 2
Pin 3
Pin 4
Pin 5
0 VDC
24 VDC
Gnd
User's Emergency Stop Switch or
other hard wired control contact.
Tie together if Emergency Stop
Switch is not required.
Power Connector
Last Module Termination
If the PVLB10 or PVLC10 manifold is the last device on the
network, a terminating resistor connector must be connected
on the Bus-OUT connector. If the network baud rate is
higher than 1.5 Mbaud, use a terminating resistor connector
with inductive filters.
0
1
2
3
4
5
6
7
8
9
0
1
2
3
4
5
6
7
8
9
21
34
5
21
34 5
21
34
5
Address x 10
Address x 1
M12
Micro BUS-IN Connector
(Male) Face View
M12
Micro POWER Connector
(Male) Face View
M12
Micro BUS-OUT Connector
(Female) Face View
Bus
Power
ERR
BA
ON
ERR
ON

Parker Hannifin Corporation
Pneumatic Division North America
Richland, Michigan
Pneumatic
6
Technical Specifications
External Power Supply .................................20.4 to 30 VDC
Bus Current ............................................................... 200mA
Maximum Current Per Outoput ................................. 350mA
Total Output Current ....................................................... 1A
Number of Outputs .......................................................... 16
Baud Rates ......................................................... 500 Kbaud
Data I.D. Code .................................................................. 03
Degree of Protection ..................................................... IP65
Operating Temperature
60% Rating .......................... 0°C to 55°C (32°F to 130°F)
100% Rating ........................ 0°C to 40°C (32°F to 104°F)
Bus-In Connector
Pin Function
1DO
2DO
3DI
4DI
5 Ground
6PE
7, 8, 9 Not Used
Bus-Out Connector
Pin Function
1DO
2DO
3DI
4DI
5 Ground
9 RBST
6, 7, 8 Not Used
Recommended Bus Connector (Or Equivalent)
Connivers #RC-09S1N128049 Female
Connivers #RC-09P1N128049 Male
Power Connector
Pin Function Comment
1 0 VDC BUS POWER
2 24 VDC
3* Valve Power VALVE POWER
4* Valve Power
5 Ground
Recomended Power Connector (Or Equivalent):
Turck female Eurofast #B 8151-0
InterBus-S
PVLB10/ PVLC10 Serial Bus Modules V-382P
Baud Rate Setting
This system operates only at 500 Kbps.
Module Status Lights (LED's)
Indicator Description
BUS SteadyGreen Normal
OFF No Power Applied
Steady Green Normal
Valves OFF No Power Applied to the
Valves
BUS-BA Steady Green Normal
FlashingGreen Configuration Problem
BUS-RC Steady Green Normal
OFF No Power Applied
BUS-ERR OFF Normal
Steady Red BUS Error
BUS-ON Steady Green Normal
OFF No Power Applied
E STOP Feature*
Output power to the solenoids can be wired to allow the user
to turn the outputs off while allowing the communications to
remain on. This can be done by placing the user's
Emergency Stop Switch or other hard wired control contact
between Pin 3 and Pin 4. If this feature is not required, Pin 3
and Pin 4 should be wired together.
Pin 1
Pin 2
Pin 3
Pin 4
Pin 5
0 VDC
24 VDC
Gnd
User's Emergency Stop Switch or
other hard wired control contact.
Tie together if Emergency Stop
Switch is not required.
Power Connector
18
27
36
45
9
18
27
36
45
9
21
34
5
M23
BUS-IN Connector
(Male) Face View
M23
BUS-OUT Connector
(Female) Face View
M12
Micro POWER Connector
(Male) Face View
ONBUSVALVE
BA
RC
ERR

Parker Hannifin Corporation
Pneumatic Division North America
Richland, Michigan
Pneumatic
7
ASI
PVLB10/ PVLC10 Serial Bus Modules V-382P
Technical Specifications
Bus Voltage .................................................. 29.5-31.6 VDC
Bus Current ................................................................. 30mA
Output Current .......................................................... 250mA
Total Output Current ....................................................... 1A
Max. Supply for all Inputs .......................................... 200mA
ID Code ............................................... 7F (4I / 4O); 8F (4O)
Degree of Protection ..................................................... IP65
Operating Temperature ........... 0°C to 50°C (32°F to 122°F)
Module Status Lights (LED's)
Indicator Description
ASI Off ASI Bus Error
Steady Green Normal
24 V Valves Off No Power
Steady Green Normal
OVERLOAD Off Normal
Steady Red Output Short Circuit
External
Power
Connector
ASI
Bus
Connector
P8L-MH02B1
ASI
Programming
Unit
External
Power
Connector
ASI
Bus
Connector
P8L-AJACK
ASI
Programming
Unit
P2SBAXXXXX-ASI Head Modules
4 Output Version
PVLBAXXXXX-ASI Head Modules
4 Input & 4 Output Version
Node Address Settings:
ASI node addresses are set through an ASI programming
unit as shown below.

Parker Hannifin Corporation
Pneumatic Division North America
Richland, Michigan
Pneumatic
8
ASI #1 ASI #2 ASI #3
Inputs Inputs Inputs Inputs
ASI #4
#4 #3 #2 #1
202
313
01230 0123 1
01
23
01
23
01
23
01
23
External Power Connector
Pin Function
1 24 VDC Valve Power
2NC
3 0 VDC
4NC
Valve Address & Input Mapping
PVLB10/ PVLC10 Serial Bus Modules V-382P
ASI
Pinout Details
Input Connector
(On PVLBAXXXXX Modules PNP Only)
Pin Function
1 24 VDC
2NC
3 0 VDC
4 Input
ASI Bus Connector
Pin Function
1A+
2NC
3A-
4NC