Parrot Uncle F8278110V Manual

www.parrotuncle.com
English ñ / Francais/ Espanol ç
F8278110V

TECHNICAL INFORMATION
SKU
120V DC 35W
Nominal Voltage Nominal output(motor) light
Safety Information
WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER
F8278110V
Installation & Operating Instructions for the
Parrot Uncle Owner's Installation, Manual
F8278110V
WARNING: TO reduce the risk of personal injury,
do not bend the blade brackets (also referred to as
flanges) during assembly or after installation. Do not
insert objects in the path of the blades.
WARNING: Remove the rubber motor stops on
the bottom of the fan before installing the blades
or testing the motor.
WARNING: To reduce the risk or fire or electric
shock, do not use this fan with any solid-state
speed control device.
WARNING: To avoid possible electric shock,
turn the electricity off at the main fuse box before
wiring. lf you feel you do not have enough electrical
wiring knowledge or experience, contact a licensed
electrician.
WARNING: Electrical diagrams are for reference
only. Optional use of any light kit shall be UL-listed
and marked suitable for use with this fan.
WARNING: To reduce the risk of fire, electric
shock, or personal injury, mount to outlet box
marked”Acceptable for fan support of 35lbs.
(15.9 kg) or less "and use the screws provided
with the outlet box.
1. To reduce the risk of electric shock, the electricity has been
turned off at the circuit breaker or fuse box before begin.
2. All wiring must be in accordance with the National Electrical
Code NASI/NFPA70-1999 and local electrical codes.
Electrical installation should be performed by a qualified
licensed electrician.
3. The outlet box and support structure must be securely
mounted and capable of reliably supporting 35lb.(15.9kg).
Use only UL listed outlet boxes marked “Acceptable for Fan
Support of 35lbs (15.9kg) or less.”
4. The fan must be mounted with a minimum of 7 ft. (2.1m)
clearance from the trailing edge of the blades to the floor.
5. Do not operate the reversing switch while the fan blades are
in motion. You must turn the fan off and stop the blades
before you reverse the blade direction.
6. Do not place objects in the path of the blades.
7. To avoid personal injury or damage to the fan and other
items, please be careful when working around or cleaning
the fan.
8. Electrical diagrams are for reference only. Light kits that are
not packed with the fan must be UL-listed and marked
suitable for use with the model fan you are installing.
Switches must be UL General Use Switches.
Refer to the instructions packaged with the light kits and
switches for proper assembly.
9. After making electrical connections, spliced conductors
should be turned upward and pushed carefully up into the
outlet box. The wires should be spread apart with the
grounded conductor and the equipment-grounding conductor
on one side of the outlet box. and the ungrounded conductor
on the other side of the outlet box.
10. All setscrews must be checked and retightened where
necessary before installation.

WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER
F8278110V
Installation & Operating Instructions for the
Parrot Uncle Owner's Installation, Manual
Pls check whether above accessories are completed or not?Yes,and install.
REMOTE CONTROL ( 1PC )
Blace screws
(42PCS+1Spare)
Locknut
(18PCS+1 Spare)
Washer
(2PCS)
Plastic wire nut (4PCS)
Screws (2PCS)
Mounting screws
(2PCS)
Mounting bracet
Hanging Pin
“R” Looking Pin
Canopy
Canopy cover
Coupling cover
6"ball/downrod assembly
Fan-motor
assembly
Cap
Blade (6PCS)
Blade arm (12PCS)

WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER
F8278110V
Installation & Operating Instructions for the
Parrot Uncle Owner's Installation, Manual
1
2
3
Coupling
Coupling screw
Loosen the two coupling screws preassembled in the
coupling , but do not remove them. Remove the
locking pin and hanging pin from the downrod
assembly. Retain for later use.
Place downrod assembly through canopy, canopy
cover and coupling cover. Route the motor lead
wires through the downrod assembly.
Screw the two mounting screws and washers to the
outlet box.Slide the mounting bracket onto the screw
through the T-slot.
Position the mounting bracket on the outlet box and
securely tighten screws and washers.
Canopy
Canopy cover
Coupling cover

WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER
F8278110V
Installation & Operating Instructions for the
Parrot Uncle Owner's Installation, Manual
4
5
Coupling screw
6 to 9 in
Hanger ball
Groove
Slide downrod into the coupling on top of the motor.
Install the hanging pin by aligning the holes in the
coupling with holes in the downrod. Secure hanging
pin with locking pin. Securely tighten the two
previously loosed set screws.
Cut off excess lead wire approximately 6 to 9 inches
above top of the downrod. Strip insulation off 1/2
inch from the end of each lead wire.
CAUTION: All set screws must be checked and
retightened where necessary before installastion.
Carefully lift the fan and seat the downrod/hanger
ball assembly onto the mounting bracket that was
just attached to the outlet box. Be sure the groove
in the ball is lined up with tab on the mounting
bracket.
WARNING: Failure to seat tab in groove could cause
damage to electrical wires and possible shock or fire
hazard.

WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER
F8278110V
Installation & Operating Instructions for the
Parrot Uncle Owner's Installation, Manual
6
LIGHT MUST BE KEPT AT THE ON POSITION
FAN MUST BE KEPT AT THE HIGH SPEED
Loosen the screws without fully removing it.
Assemble canopy by rotating key slot in
canopy over screws in mounting bracket,
taking care notto pinch the wires.
Tighten the screws.
Slide the receiver into the open end
of the mounting bracket with the
flat side of the receiver facing the
ceiling.
YELLOW (TO MOTOR U)
GRAY (TO MOTOR V)
RED (TO MOTOR M)
YELLOW (TO MOTOR)
GRAY (TO MOTOR)
RED (TO MOTOR)
BLACK (AC IN L)
GREEN
GREEN GREEN
GREEN
WHITE (AC IN N)
BLACK (L) WHITE (N)

WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER
F8278110V
Installation & Operating Instructions for the
Parrot Uncle Owner's Installation, Manual
6
7
8
Blade screws (3PCS)
Locknuts (3PCS)
Attach blade arms to blade as shown. Screw the
blade screws (provided in the hardware bag) into the
screw holes and tighten it with the locknuts by using
a wrench.
Repeat the same steps for the remaining blades.
Position blade assembly along the motor and make
sure the blade arm is fully seated against the flywheel.
Tighten them with four blade screws.
Repeat the same steps for the remaining blade
assemblies.
Securely attach and tighten the canopy cover over the
screws in the mounting bracket utilizing the key slot
twist-lock feature.
Note: Adjust the canopy screws as necessary until
the canopy and canopy cover are sung.

WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER
F8278110V
Installation & Operating Instructions for the
Parrot Uncle Owner's Installation, Manual
Whole structure
9
10
Assemble the cap to the threaded rod by twisting in
a clockwise direction.

WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER
F8278110V
Installation & Operating Instructions for the
Parrot Uncle Owner's Installation, Manual

WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER
F8278110V
Installation & Operating Instructions for the
Parrot Uncle Owner's Installation, Manual
7
a. WARNING: Chemical Burn Hazard. Keep batteries away from children.
b) This product contains a lithium button/coin cell battery. If a new or used lithium button/coin cell
battery is swallowed or enters the body, it can cause severe internal burns and can lead to death in
as little as 2 hours. Always completely secure the battery compartment. If the battery compartment
does not close securely, stop using the product, remove the batteries, and keep it away from children.
If you think batteries might have been swallowed or placed inside any part of the body, seek
immediate medical attention.
c) The cells shall be disposed of properly, including keeping them away from children; and
d) Even used cells may cause injury
35W120 V
yellow
Voltage Fan (max.)
Antenna wire
Ground wire
Power supply live-wire
To Motor wire
Red
Gray
To Motor wire
To Motor wire
Power supply neutral-wire
56
WIRING SCHEMATIC DIAGRAM FOR RECEIVER
POWER PARAMETER LIST
FUNCTION INSTRUCTION OF EMITTER
KINDLY REMINDERS:
Green
White wire
Black wire
8
LED indicated light
Turn up the speed of the fan
Direction of the fan
(reverse switch)
Timing control of the fan
ON/OFF the fan
Turn down the speed of the fan
Short press: ON/OFF the light
Long press: Adjust the brightness
of the light
3V CR2032 battery X 1pcs
8
Adopt RF wireless digit emission technique, biunique controlled , coincident code rate is less than one
millionth. (Emitter and receiver must be sent back to factory for maintenance if damaged.)
Receiver can be controlled by any angles of the emitter in prescriptive space, unrestricted by direction.
With the memory function, the controller can save the status( light and direction ) while the supply
power OFF and resume to the original after reload the power supply.
1. If the emitter can not control the fan, learning code matching mode is used between emitter and receiver.
Turn “ON" the supply power within 30 seconds and press the emitter's “ ” button for 5 seconds, it can load
normally after hearing a long sound “bee”, which means learning successfully and it can works normally.
(PS: Learning mode is not accepted after turn “ON” the supply power for 30 seconds)
2. When the emitter cannot control the receiver, please check the battery switch touching normally or not, correction of the positive
and negative, full or empty of the power.
3. When the emitter cannot control the receiver, please check is there any existence of similar remote controlled products nearby,
then check whether they works, because remote controlled product with the same frequency will disturb each other.
4. Low voltage of battery will affect the sensitivity of the emitter and the signal reception accordingly(the indicated light will flash
out its warning when the battery get low voltage), must replace if the battery is getting low voltage.
5. Please take out the battery from the emitter when leaving unused for long time.
6. The maximum load of lighting see the above“POWER PARAMETER LIST”
PS: please connect the ground wire correctly, otherwise it may cause the light micro-light or flash
7. When installing the fan, the fan ceiling cover don't press the antenna (or other wire), it is easy to breakdown the wire and
short-circuited.
WIRING SCHEMATIC DIAGRAM FOR RECEIVER
POWER PARAMETER LIST
Green
White wire
Black wire

WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER
F8278110V
Installation & Operating Instructions for the
Parrot Uncle Owner's Installation, Manual
Ø70"
12.9" 10.4"
2.0"
6.1"
6.0"
SIZE OF PRODUCT

WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER
F8278110V
Installation & Operating Instructions for the
Parrot Uncle Owner's Installation, Manual
TROUBLESHOOTING GUIDE
1.FAN / REMOTE IS NOT WORKING
2.THE FAN IS NOISY
3.THE FAN WOBBLES
Ensure the remote is within the 20 foot range of the receiver
To reset the remote control: 1) Turn off power to fan using the wall switch or circuit breaker.
2) Remove batteries from remote. 3) Wait 10 seconds. 4) Replace batteries and turn power on
Check batteries to insure they are good and oriented correctly
Check to make sure the frequency switches (DIP Switches) from the remote to the receiver are
set to the same frequency
Check the main and branch circuit fuses or breakers
If using a Variable Speed Wall Switch,ensure it is specifically designed for use with a ceiling fan.
Check the line wire connections to the fan and the switch wire connections in the switch housing per the instructions
If fan still does not work, please contact Customer Service Support@Parrot Uncle.com
Make sure all motor housing screws are tight
Make sure the screws that attach fan blade to motor are tight
Make sure the wire nut connectors are not rattling against each other or the interior wall of the switch housing
Allow 24-hour break in period. Most noises associated with the new fan may disappear during this time
if using a ceiling light kit,make sure the glassware is secured tightly
Make sure there is a short distance/gap from the ceiling to the top of the canopy. The canopy should not touch the ceiling!
Make sure your ceiling box is secure and that the rubber insulating pads are used between the mounting bracket and outlet box
Verify all blades and blade bracket screws are secure (most fan wobble problems are caused by loose parts).Once fan is properly
installed,run the ceiling fan for 10 minutes to let the fan self-adjust.
If wobble occurs after running the fan for 10 minutes, verify blade level using the following process:
a) select a point on the ceiling above the tip of one of the blades. Then select the fan blade and measure from the center
of the selected blade to point on the ceiling. Rotate the fan until the next blade is positioned and repeat the
measurement using the same point from the ceiling for every blade. Measurements should be within 1/8 inch.
b) If all deviation are less than 1/8 inch and the fan continues to wobble, please contact Customer Service Support@parrot Uncle.
com to order a complimentary Blade Balancing Kit
-If all deviation are less than 1/8 inch and the fan continues to wobble, please contact Customer service Support@Parrot Uncle.
com to order a complimentary Blade Balancing Kit.

WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER
F8278110V
Installation & Operating Instructions for the
Parrot Uncle Owner's Installation, Manual
AFTER INSTALLATION
AFTER INSTALLATION
Wobble
The fan blades have been adjusted in the factory to minimize any wobble
Note: ceiling fans tend to move during operation due to the fact that they are mounted on a rubber
grommet. If the fan was mounted rigidly to the ceiling, It would cause excess vibration. Movement of
A few centimeters is quite acceptable and does not suggest any problem to reduce the fan
Wobble: Please check that all screws which secured the mounting bracket and downrod are secure.
Balancing a wobbling ceiling fan:
1. Check that all blade and blade arm screws are secure.
2. Most fan wobbling problems are caused when blade levels are unequal. Check this level by electing a point on
the ceiling above the tip of one of the blades. Measure this distance. Rotate the fan until the next blade is
positioned for measurement. Repeat for each blade. The distance deviation should be equal within 1/8"(0.32cm).
3. If the blade wobble is still noticeable, Interchanging two adjacent (side by
side) blades can redistribute the weight and possibly result in smoother
operation.
Warning: To reduce the risk of personal injury, Do not bend the blade
arm while installing, Balancing the blades, or cleaning the fan. Do not
insert foreign objects between rotating fan blades.
Noise
When it is quiet (especially at night) you may hear occasional small noises. This is normal.
Please allow a 24-hour “breaking-in” period, Most noises associated with a new fan disappear during the time.
Care and cleaning
1.Periodic cleaning of your ceiling fan is the only maintenance required. Use a soft brush or lint free cloth to
avoid scratching the paint finish. Please make sure to turn off electricity power before you clean your fan
2.Do not use water when cleaning your ceiling fan. It could damage the motor or the blades and create the
possibility of an electrical shock.
3.Motor has permanently lubricated ball bearing. No need to oil.
Note: Make sure the power is off at the electrical panel box before you attempt any cleaning or repairs.
Touching
Ceiling