Paxton Genie WIP2FRTMTP User manual

Genie WIP2FRTMTP
Overview
Setting up Temp only mode
3rd Party
The Genie reader can be used with Net2 to permit or deny
access based on the user’s temperature and if required
force the user to wear a facemask. When a temperature is
detected outside of the set threshold the reader will notify
the user that there is an abnormal temperature and deny
access.
This application note will run through the following modes
of operation:
• Temp/ Mask only
• Token (MIFARE® only) + Temp
• Face + Temp
Out of the box, the Genie reader will permit access by ring the lock relay on the reader when it
identies a face record or a password is entered allowing access. To setup for Temp only mode
see notes below for setting that need to be changed in the Genie reader menu.
Using this method, the Genie reader relay can be wired in line with a Paxton reader on the Yellow data
port. This will prevent the Paxton reader from functioning until the user has passed the temperature
check.
The default door lock delay on the Genie reader is 3 seconds. To allow sucient time for the user to
present their token to the Paxton reader, you may wish to increase this via the menu on the Genie
reader.
NO
NC
COM
1

3rd Party
Ensure any unused wires are safely terminated.
ACU terminal
+12V
Red LED
Amber LED
Green LED
Wiegand D0
Wiegand D1
NOT USED
0V
Genie
NOT USED
NOT USED
NOT USED
NOT USED
W0
W1
GND
NOT USED
Net2 ACU Settings
Setting up modes: Token + Temp & Face + Temp
Connecting the reader to a Net2 Plus controller
There are two other main modes of operation; Token + Temp and Face + Temp (both options you can
enforce the user to wear a mask as well). In both cases the Genie reader should be wired to the Net2
plus as shown in the diagram below:
Congure the reader port settings for the ACU the reader has been connected to as shown in the
screenshot below:
*Users must be enrolled on both the Genie reader, and in Net2. Additional users will need to be
added separately in each system.
Once you have wired up the reader and setup the reader in Net2, the Genie reader will need to be
congured. Using the instructions provided with the reader, update the following settings:
• Access Control Settings type - should be set in the menu, select your desired operating mode
Access Control Settings->Door Opening Mode->Toggle “On”“Normal Temperature”/ “Mask”if
required. Toggle “On/O”“Face Mode” and “Password Mode”if functions required
• Temp settings - can be changed in the “System Setting”->”Temperature Measurement”->
“Temperature Settings”over the range;”Access is denied”
Genie Reader Required Settings

3rd Party
Net2 ACU Settings
For further information please visit the manufacturers website:
http://genieaccess.com/product/wip2frtmtp/
• Should a both a user’s face and temperature be authenticated, but then denied access based
on time zone permissions on the Net2 system, there will be no notication on the panel
• High temperature events cannot be sent from the Genie reader to Net2
• Temperature tolerance may need to be changed
If using with Wiegand option then you will need to enable Wiegand Out on the Genie reader. Access
Control Settings-> Toggle “On”“Wiegand Out”
[phone]
paxton.support
[e-mail]
[phone]
paxton.support
[e-mail]
[phone]
usapaxton.support
[e-mail]
[phone]
paxton.gmbh.support
[e-mail]
[phone]
paxton.support
[e-mail]
[phone]
paxton.soporte
[e-mail]
[phone]
[e-mail]
paxton.support
[phone]
paxton.benelux.support
[e-mail]
[phone]
paxton.benelux.support
[e-mail]
8000 3570 3783
paxton.support
[e-mail]
[phone]
[e-mail]
paxton.soporte