PB TEEN Display-It Desk User manual

www.pbteen.com
Display-It Desk
IMPORTANT SAFETY INSTRUCTIONS:
•Please read all instructions carefully before assembling.
•For your safety, assembly by two adults is recommended.
ASSEMBLY INSTRUCTIONS:
1. Insert the Shelf Support (S) into the pre-drilled holes inside the Door Pedestal (C). Place the Shelf (D) on
the Shelf Supports (S).
2. Pull out the bottom drawer by pressing the clips on both of the metal glides on the sides of the drawers to
release it from the Drawer Pedestal (B), as shown below. Place the File Grids (K) on the cut-outs of the
drawer. There are two positions. One is for legal size and the other is for letter size.
Hardware Included with Hardware Included with
Two Drawer Pedestal: Desk Door Pedestal:
(F) Allen Key – 1pc (N) Allen Key – 1pc
(G) Bolt ¼” x 25mm – 4pcs (O) Bolt ¼” x 25mm – 4pcs
(H) Spring Washer – 4pcs (P) Spring Washer – 4pcs
(I) Flat Washer – 4pcs (Q) Flat Washer – 4pcs
(J) Wooden Dowel – 4pcs (R) Wooden Dowel – 4pcs
(K) File Grid 2pcs (S) Shelf Support – 4pcs
(L) Cable Clip - 1pc
(M) Wood screw
3.5x15mm -1pc
PARTS INCLUDED:
(A) Desk Top – 1pc
(B) Drawer Pedestal – 1pc
(C) Door Pedestal – 1pc
(D) Shelf – 1pc
(E) Keyboard Tray – 1pc
One Door Pedestal
Two Drawer Pedestal

www.pbteen.com
3. Open the top drawer of the Drawer Pedestal (B). Press the clips on both sides of the drawer-mounted
metal glides to release the drawer box from the Drawer Pedestal (B).
4. Place the Drawer Pedestal (B) on the left and the Door Pedestal (C) on the right. Insert the Wooden
Dowels (J&R) into the pre-drilled holes on the tops of the two pedestals. Align and connect the Desk Top
(A) to the Wooden Dowels (J&R). Secure the Desk Top (A) to the Drawer Pedestals using the Bolts (G),
Spring Washers (H) and Flat Washers (I). Secure the Desk Top (A) to the Door Pedestal using the Bolts
(O), Spring Washers (P) and Flat Washers (Q). Check alignment before fully tightening all bolts.
5. Place the drawer back into the Drawer Pedestal (B) with the cable of the cord set (pre-installed) going
through the cut-out on back panel. Use the Cable Clip (L) and Wood Screw (M) to secure the cable in
place when required.
6. Align and attach the Keyboard Tray (E) to the metal glides pre-installed under Desk Top (A) by pressing
the clips on both sides of the Keyboard Tray (E) and inserting the Keyboard Tray (E) into the metal glides.
CARE INSTRUCTIONS:
•Dust with a soft, dry cloth.
•Use furniture was as needed.
•Avoid abrasives and solvent cleaners.

www.pbteen.com
Display-It Desk Hutch
MPORTANT SAFETY INSTRUCTIONS:
Please read all instructions carefully before assembling.
For your safety, assembly by two adults is recommended.
Assembly Instructions:
1. Place the Desk Hutch (A) on the assembled Desk (sold separately).
2. Line up the insert nuts on back of the Desk Hutch (A) and desk. Align and place the Bracket (D) over the
insert nuts and secure using Bolt (E), as shown below. Tighten with a Phillips Head Screwdriver.
3. Insert the Shelf Support Pegs(C) into the pre-drilled holes on the interior sides of the Desk Hutch’s center
cubby (A). Place the Shelf (B) onto the Shelf Support Pegs (C).
Parts Included: Hardware Included:
A - Desk Hutch – 1pc C - Shelf Support Pegs - 4pcs
B - Shelf – 1pc D - Bracket - 4pcs
E - Bolt 5/32” x 15mm
- 8pcs
Tools Required:
Philips Head Screwdriver (not included)
D.
E.
E.
Care Instructions:
•Dust with a soft, dry cloth.
•Avoid abrasives and solvent
cleaners.

www.pbteen.com
Display-It Desk Hutch
FURNITURE TIPPING RESTRAINT
Young children may be injured by tipping furniture. The use of a tipping restraint is highly recommended.
When properly installed, this restraint could provide protection against the unexpected tipping of furniture due
to small tremors, bumping or climbing. We recommend mounting this restraint to a wall stud.
WARNING: This product is only a deterrent. It is not a substitute for proper adult supervision.
Hardware Included:
Installation Instructions:
1. Locate a wall stud behind your furniture. Position a Plastic Wall Bracket (G) on the stud approximately 1”
below the top of the furniture. Mark and drill pilot hole into the center of the stud with a 3/32” drill bit.
Attach a Plastic Wall Bracket (G) to the stud with the Long Wood Screws (I) provided.
2. On the back of the furniture, the second Plastic Wall Bracket (G) will need to be attached to the furniture
frame at the top. To do this, temporarily move the furniture into its final position and mark the location of
the wall’s Plastic Wall Bracket (G) on the furniture frame with a pencil.
3. Move the furniture away from the wall and place a Plastic Wall Bracket (G) on the mark. Using the marks
from the previous step as a guide, drill holes for screws with a 3/32” drill bit. Attach the Plastic Wall
Bracket (G) to the furniture with the Short Wood Screws (H) provided.
4. Move the furniture into its final position, taking care to line up the wall’s Plastic Wall Bracket (G) with the
furniture’s Plastic Wall Bracket (G). Thread the Plastic Restraint (F) through the Plastic Wall Brackets (G)
and clinch as shown in the illustration. Tighten strap until snug. Do not over tighten.
Short wood screw
Plastic wallbracket Long wood screw
Plastic restraint
F - Plastic Restraint ( 1 pcs )
G - Plastic Wall Bracket ( 2 pcs )
H. Short Wood Screw 3 x 19mm ( 2 pcs )
I. Long Wood Screw 3 x 32mm ( 2 pcs )