PB TEEN Hampton Corner Media User manual

1/7
www.pbteen.com
Hampton Corner Media
! CAUTION
•The top shelf of this cart/stand is intended for use only with Plasma/LCD/DLP/HD televisions having a
maximum screen size of 45 inches and weight of 100 lbs ; or Tube televisions having a maximum screen
size of 27 inches and weight of 95 lbs.
•All other support shelves should not be loaded more than 45 lbs.
•DO NOT EXCEED RECOMMENDED LOAD. Use with products heavier than the maximum sizes and
weights indicated may result in instability causing possible injury.
•This unit contains a permanent sticker located either beneath media support shelf or inside drawer.
•Do not allow children under 16 years to move cart.
! MISE EN GARDE
•L’étagère supérieure de ce support ou chariot est destinée à recevoir une télévision à écran plasma ou
haute densité dont l’écran ne mesure pas plus de 114.3cm et qui ne pèse pas plus de 45.4 kg. ou bien
une télévision à tube cathodique don’t l’écran ne mesure pas plus de 68.58 cm et qui ne pèse pas plus de
43.09 kg.
•Les autres étagères ne doivent pas recevoir une charge de plus de 20.45 kg.
•NE PAS DÉPASSER LA CHARGE RECOMMANDÉE. L’utilisation avec des articles qui dépassent la taille
et le poids recommandés peut rendre l’article instable et entraîner des blessures.
•Cet article comprend un autocollant permanent, placé soit sous l’étagère supérieure, soit à l’intérieur du
tiroir.
•Il faut interdire à tout enfant de moins de 16 ans de déplacer le chariot.
04-000077-2
PRE-ASSEMBLY:
•For your safety and ease, assembly by two adults is recommended.
•Read all instructions before beginning assembly.
•Remove all parts and hardware from box and lay out on a carpeted or scratch-free work surface. The
shipping box provides and ideal work surface. Do not dispose of any contents until assembly is completed
to avoid accidentally discarding small parts or hardware.
PARTS INCLUDED:
A - Front Top panel - 1pc
B - Rear Top panel - 1pc
C - Bottom panel - 1pc
D - Left side panel - 1pc
E - Right side panel - 1pc
F - Left partition panel - 1pc
G - Right partition panel – 1pc
H – Back panel – 1pc
I - Back support panel – 1pc
J – Left door – 1pc
K – Right door – 1pc
L – Center support leg – 1pc
M – Triangle shelf – 2pcs
N – Center shelf – 1pc

2/7
www.pbteen.com
HARDWARE INCLUDED:
O – Allen Key – 1 pc P – Long hex bolt – 4 pcs Q – Short hex bolt – 12 pcs
1/4” × 45 × 13mm 1/4” × 28 ×
13mm
R – Half moon washer – 4 pcs S – Bolt – 8 pcs T – Phillips head screw – 12 pcs
1/4” × 24 × 8mm 5/32” × 13mm 7 × 19mm
X – Phillips head screw – 14 pc Y – Pan head screw – 10 pcs Z – Shelf support peg – 10 pcs
6 × 15mm 8 × 15mm 5 × 13 × 16 × 1.5mm
TOOLS REQUIRED (but not included):
Phillip Head Screwdriver
ASSEMBLY INSTRUCTIONS:
1. Lay Bottom panel (C) on its longest side on a soft, scratch-free surface. Attach Left side panel (D) and
Right side panel (E) to the bottom panel by aligning wooden dowels with pre-drilled holes on these
components, insert 4 Long Hex Bolt (P) through 4 Half moon washers (R) then insert the bolts with
washers through pre-drilled holes in slots underneath the Bottom panel into metal inserts in side panels as
shown below, Loosely tighten the bolts with Allen Key (O).

3/7
www.pbteen.com
2. Attach the Left partition panel (F) and Right Partition panel (G) to Bottom panel (C) by aligning wooden
dowels on partition panels with pre-drilled holes in the bottom panel, insert 4 Short hex bolts (Q) through
pre-drilled holes in the Bottom panel into metal inserts in partitions as shown below, Loosely tighten the
bolts with Allen Key (O).
3. Attach Center support leg (L) by turning hanger bolt on the support leg into metal insert underneath the
Bottom panel as shown below.

4/7
www.pbteen.com
4. Lay Top panels (A&B) upside down on a soft, scratch-free surface. Attach the Rear top panel (B) to Front
Top panel (A) by aligning pre-drilled holes in hinges with pre-drilled holes at back of the front top panel.
Insert a Phillips head screw (T) through each pre-drilled hole in the hinges into pre-drilled hole at the front
top panel as shown below; tighten screws with Phillip head screwdriver.
5. Put assembled top panels onto side panels and partitions by align pre-drilled holes underneath top with
wooden dowels on side panels and partitions. Insert 2 Short hex bolts (Q) through pre-drilled holes of
each cleat on side panels and partitions into metal inserts in the top as shown below. Tighten ALL bolts
with Allen Key (O) after these bolts are in place.

5/7
www.pbteen.com
6. Fix Back panel (H) to the corner media with 14pcs Phillips head screw (X) as shown below, use pre-drilled
holes in back panel as guidance. tighten all screws with Philips Head screw driver.
7. Attach the Back support panel (I) to the right side of back panel by inserting 6pcs Phillips head screw (T)
through pre-drilled holes in the hinge into pre-drilled holes in back panel as shown below , tighten screws
with Phillip head screwdriver.

6/7
www.pbteen.com
8. Attach Left door (J) and Right door (K) to the Left side panel (D) and Right side panel (E),align pre-drilled
holes in hinges on doors with metal inserts on corresponding side panels, insert 2 Bolts (S) through pre-
drilled holes in each hinge into the metal inserts on side panels as shown below, tighten the bolts with
Phillip head screwdriver.
9. Chose desired height for shelves and Insert Shelf support pegs (Z) into corresponding holes in the side
panels and partitions, note each compartment behind doors takes 3 shelf pegs, the center compartment
takes 4 shelf pegs. Place shelves onto the shelf pegs, fix each Shelf support peg with a Pan head screw
(Y) and Philips head screw driver as shown below.

7/7
www.pbteen.com
10. Adjust levers under feet and/or center support leg of the unit in or out to level the Media.
CARE INSTRUCTIONS:
•Avoid direct sunlight and excessive temperatures.
•Dust often using a clean, soft, dry and lint-free cloth.
•Waxing is not recommended on lacquered finish.
•Hardware should be checked periodically for tightness.