PB TEEN Stuff-Your-Stuff Loft Bed User manual

www.pbteen.com
Stuff-Your-Stuff Loft Bed
WARNING:Failure to follow these warnings and assembly instruction
could result in serious injury or death.
•Read all instructions before assembling bunk bed. KEEP INSTRUCTIONS
FOR FUTURE USE.
•Before each usage or assembly, inspect bunk bed for damaged hardware,
loose joints, missing parts or sharp edges. DO NOT use bunk bed if any parts
are missing or broken. Telephone or write to PB teen for replacement parts and
instructional literature if needed. DO NOT substitute parts.
•Follow the information on the warning appearing on the upper bunk end
structure and on the carton. DO NOT REMOVE WARNING LABEL FROM THE
BED.
•Never allow a child under 6 years on upper bunk.
•Use only mattress which is 74”-75” long and 52.5”-53.5” wide on upper bunk.
•Ensure thickness of mattress does not exceed 9” and mattress is at least 5”
below upper edges or guardrails.
•Always use the recommended size mattress or mattress support, or both, to
help prevent the likelihood of entrapment or falls.
•Surface of mattress must be at least 5 inches (127 mm) below the upper edge
of the guardrails.
•Periodically check and ensure that the guardrail, ladder and other components
are in their proper position, free from damage, and that all connectors are tight.
•Do not allow horseplay on or under the bed and prohibit jumping on the bed.
•Always use the ladder for entering and leaving the upper bunk.
•Use of a night light may provide added safety precautions for a child using the
upper bunk.
•Always use guardrails on both long sides of the upper bunk.
•Prohibit more than one person on the upper bunk.
•If upper bunk bed will be placed against the wall to prevent entrapment
between the bed and the wall.
•If refinishing, use a non-toxic finish specified for children’s products.
•STRANGULATION HAZARD – Never attach or hang items to any part of the
bunk bed that are not designed for use with the bed; for example, but not
limited to, hooks, belts, and jump ropes.
•The use of water or sleep flotation mattress is prohibited.
04-000066-1

www.pbteen.com
PRE-ASSEMBLY:
•Please read all instructions before beginning assembly.
•Remove all parts and hardware from the box and lay out on a clear carpeted or scratch-free work surface. (The
shipping box provides an ideal work surface), this will avoid damaging any parts during assembly. Do not dispose
of any contents until assembly is completed to avoid accidentally discarding small parts or hardware.
•Three adults are recommended for ease of assembly.
•Use the parts and hardware lists to identify and separate each of the pieces included prior to starting assembly.
•The illustrations provided allow for easier assembly when used in conjunction with the assembly instructions.
•Note: Do not fully tighten all bolts until all parts are in place. Failure to follow these instructions may cause the
bolts to misalign during assembly.
•If using power tools to aid in assembly please use caution. Power tools can damage hardware or split wood.
•Save your allen key and other tools to retighten the hardware after it has been used for awhile. This piece of
furniture should be retightened periodically.
PARTS INCLUDED:
(A) Headboard -1pc
(B) Footboard -1pc
(C) Left side rail -1pc
(D) Right side rail -1pc
(E) Top rail -1pc
(F) Center rail -1pc
(G) Bottom rail -1pc
(H) Supporter block -2pcs
(I) Support rail -1pc
(J) Guard rail -1pc
(K) Ladder -1pc
(L) Slat Roll -1Set
TOOLS REQUIRED:
Phillips head screwdriver (not included)
HARDWARE ENCLOSED:
(M) 4&5mm Allen key -2pcs
(N)BarrelNut-14pcs
(O)5/16x5”Bolt-14pcs
A
B
C
D
E
F
G
H
I
K
L
J

www.pbteen.com
(P) 5/16 x 1-1/4”Bolt-2pcs
(Q) 5/16” Sleeve Nut -1pc
(R) 5/16” x 11.5” Stud Bolt -2pcs
(S) #8x25mm Screw -28pcs
(T) #8x20mm Screw -20pcs
(U) Mounting Plate -2pcs
(V) 1/4 x 5/8” Bolt -4pcs
(X) Mending plate -2pcs
ASSEMBLY INSTRUCTIONS
1. Insert the 5/16” x 11.5” Stud bolt (R) into the pre-drilled holes in the center of the Right Siderail (D), as shown.
Screw in until secure. (Fig. 1)
Fig. 1
D
R

www.pbteen.com
2. Attach the Supporter Block (H) and Guard Rail (F) to the Right Side Rail (D) by inserting the Stud Bolt (R),
assembled in Step #1, through the pre-drilled holes in the center of the Supporter Block (H) and through the
pre-drilled hole in the center of the Guard Rail (F), as shown. Ensure that the pre-drilled holes at the ends of the
inner face of Guard Rail (F) and the Right Side Rail (D) are facing each other. See (Fig.2). Once the Guard
Rail (F) is attached, place another Supporter block (H) on top of it, making sure the Stud Bolt (R) goes into the
center pre-drilled hole of the Supporter Block (H). (Fig. 2)
3. Assemble Mounting Plates (U) onto Headboard (A) & Footboard (B) using the pre-drilled holes. Fasten
mounting plates to Headboard (A) and Footboard (B) using (8) #8 x 20mm Screws (T) as shown below. (Fig.3).
Loosely tighten with a Philips Head Screwdriver (not included). Once all Screws (T) are in place, fully tighten.
With 3 adults, attach the assembled part from Step 2 to the Headboard (A) and Footboard (B). With one adult
holding the Headboard (A) and another holding the Footboard (B), on adult should lift the assembled part from Step
2 and insert the pre-attached wooden dowels of the Guard Rail (F) and the Right Side Rail (D) into the pre-drilled
holes on the Headboard (A) and Footboard (B).
Fig. 2
Fig. 3
D
F
H
A
B
T
U

www.pbteen.com
4. Secure the Headboard (A) and Footboard (B) to the assembled part from Step 2 by inserting (6) 5/16” Barrel
Nuts (N) into the pre-drilled holes on the interior facing sides of the Right Side Rail (D) and the Guard Rail (F),
as shown below. Please make sure the hole of the Barrel Nuts (N) is facing toward the pre-drilled hole on the
end of each rail. Then, insert the (6) 5/16” x 5” Bolt (O) through the pre-drilled hole on the posts of the
Headboard (A) and Footboard (B) and into the Barrel Nut (N) just inserted. Loosely tighten with the Allen Key
(M). Do not tighten securely all bolts in this step. (Fig. 4)
5. Secure the Headboard (A) and Footboard (B) to the Left Side rail (C) by inserting (4) 5/16” Barrel Nuts (N) into
the pre-drilled holes on the interior facing sides of the Left Side Rail (C). Please make sure the hole of the
Barrel Nuts (N) is facing toward the pre-drilled hole on the end of each rail. Then, insert the (4) 5/16” x 5” Bolt
(O) through the pre-drilled hole on the posts of the Headboard (A) and Footboard (B) and into the Barrel Nut (N)
just inserted. Loosely tighten with the Allen Key (M). Do not tighten securely all bolts in this step. (Fig 5)
Fig. 4
A
B
O
N
C
N
O
Fig 5

www.pbteen.com
6. Align and insert the pre-attached wooden dowels of the Bottom Rail (G) into the pre-drilled holes on the leg
posts of the Headboard (A) and Footboard (B). Make sure the pre-drilled holes on the Bottom Rail (G) are
facing outward. Secure the Bottom Rail (G) to the Headboard (A) and Footboard (B) by inserting the 5/16”
Barrel Nuts (N) into the pre-drilled holes on the outward-facing side of the Bottom Rail (G). Then, insert a 5/6”
x 5” Bolt (O) through the pre-drilled holes on the exterior side of the Headboard (A) and Footboard’s (B) leg
post and into the pre-drilled holes of the Bottom Rail (G), making sure the Bolts (O) go into the Barrel Nuts (N)
just inserted into the Bottom Rail (C). Securely tighten all bolts that were assembled in Steps 4, 5, 6 with the
Allen Key (M). (Fig 6)
7. Attach the Top Rail (E) to the Headboard (A) and Footboard (B) by placing the Top Rail (E) on the top of the
post. Insert (2) 5/16” x 1-1/4” Bolts (P) into the pre-drilled holes at the end of the Top Rail (E). Loosely tighten
with the Allen Key (M). Then, insert (1) 5/16” Sleeve Nut (Q) into the pre-drilled hole in the center of the Top
Rail (E). Loosely tighten with the Allen Key (M). Once all bolts and nuts are in place, fully tighten them using
the Allen Key (M). (Fig.7)
Fig. 7
D
P Q
E
G
O
N
Pre-drilled holes
are facing out ward

www.pbteen.com
8. Carefully lift Support Rail (I) onto Mounting Plates (U) on Headboard (A) and Footboard (B). Secure the
Supporting Rail (I) by inserting (4) #8 x 20mm Screws (T) through the pre-drilled holes on the Mounting Plate (U)
and the pre-drilled holes located at both ends of the Support Rail (I). Loosely tighten with a Philips Head
Screwdriver (not included). Once all Screws (T) are in place, fully tighten. See (Fig. 8).
9. Assemble Mending Plate (X) onto Guard Rail (J) using the pre-drilled holes. Insert (4) 1/4 x 5/8” Bolt (V) into
the pre-drilled holes at the end of Guard Rail (J). Loosely tighten with the Allen Key (M). See (Fig.9).
Fig. 8
T
I
Fig. 9 V
X
J

www.pbteen.com
10. Slide guard rail (J) onto Left Side Rail (C) as show below (Fig.10).
11. Fasten metal brackets that are already attached to Guardrail (J) into pre-drilled holes on Left Side Rail (C).
Fasten Guardrail (J) to Left Side Rail (C) using (4) #8 x 20mm Screws (T) .Turn the pre-attached mending
plates located on the underside edge of the Guard Rail (J) and align them with pre-drilled holes located on the
bottom edge of Left Side Rail (C). Secure in place using (2) #8 x 20mm Screws (T). Tighten all screws (T) with
Philips head screwdriver.(Fig.11)
Fig. 10
Fig. 11
J
C
T
T

www.pbteen.com
12. Lay the Slat Roll (L) down onto the inner ledges of the Side Rails (C) and (D). Attach the Slat Roll (L) by
inserting the #8 x 25mm Screws (S) through the pre-drilled holes on the end of the Slat Roll (L) and into the
inner ledges of the Side Rails (C) and (D). Loosely tighten with a Phillips Head Screwdriver (not included), as
shown in (Fig.12). Once all Screws (S) are in place, fully tighten.
13. Fasten the Ladder (K) to the Left Side Rail (C) by placing the bracket of the Ladder (K) over the ledge of the the
Left Side Rail (C). Insert (2) #8 x 20mm Screw (T) through the pre-drilled holes of the bracket on the Ladder
(K) and into the Side Rail (C), as shown. (Fig.13)
Fig. 12 S
Fig. 13
T

www.pbteen.com
14. If your floor is not perfectly even, the furniture may not sit level and cause it to wobble. If the piece wobbles,
determine which corner does not touch the ground correctly. With two people follow these steps:
zCarefully elevate the item slightly to provide access to the levelers attached to the bottom.
zTurn the levelers in a counter-clockwise direction.
zGently set down the piece and check stability.
zRepeat steps until the furniture sits firmly on the ground.
CARE INSTRUCTIONS:
zAvoid direct sunlight and excessive temperatures.
zDust often using a clean, soft, dry and lint-free cloth.
zDo not use glass cleaner, abrasives, wax or household cleaners on wood.