PB TEEN ROWAN OVERHEAD BRIDGE User manual

www.pbteen.com Page 1 of 6
ROWAN OVERHEAD BRIDGE
ASSEMBLY INSTRUCTIONS
Date: 2015-April-14

www.pbteen.com Page 2 of 6
Important Safety Instructions:
•Please read all instructions carefully before assembling.
•For your safety, assembly by two or more adults is strongly recommended.
•Keep instructions for future use.
•Use only vendor supplied hardware to assemble. Using unauthorized hardware could jeopardize the
structural integrity of the item.
Pre-assembly:
•Remove all parts and hardware from the box and lay out on a clear carpeted or scratch-free work surface,
as this will avoid damaging parts during assembly. The shipping box provides an ideal work surface.
•Do not dispose of any packaging or contents of the shipping carton until assembly is completed to avoid
accidentally discarding small parts or hardware.
•Use the parts and hardware lists below to identify and separate each of the pieces included.
•The illustrations provided allow for easier assembly when used in conjunction with the assembly
instructions.
•The use of power tools to aid in assembly is not recommended. Power tools can damage hardware and
split wood.
Parts Included :
Hardware Included:
(A) Overhead Bridge
1 pc
(C) Allen Bolts
(M6 x 20mm)
8x
(D) Spring Washer
8x
(E) Metal Washer (2mm)
8x
(F) Allen Key
2x
(G) Metal Bracket
4x
(H) Sleeve Nut
4x
(I) Allen Bolts
(M6 x 30mm)
4x
(J) Drill Bit ø9mm
1 set
Tools Required (not included):
Philips Head Screwdriver 1x

www.pbteen.com Page 3 of 6
Assembly Instruction Steps:
1. Assemble the Metal Brackets (G) on top of both ends of the Bridge for support while connecting the
storage tower with the Bridge. Secure with Bolts (C), Spring washer (D) and Metal washer (E) tighten with
the Allen Key (F), as shown below. Note: Make sure the brackets are perpendicular to the sides.
2. Before attaching the bridge to the 2 tower bookcases, make sure the 2 holes on the upper side of Tower
Bookcase (sold separately) are drilled through with the ø9mm Drill Bit (J) supplied as shown below.
J
G
CD
E
F

www.pbteen.com Page 4 of 6
3. Stand the Bookcase Towers upright apart against the wall, using the bridge (A) as a measuring guide to
place the second tower bookcase. With 2 people lift the Overhead Bridge (A) above the Towers. Lay the
exposed Metal Brackets attached to the bridge on top of the Towers as a temporary hanging method.
Assemble the Bridge (A) to the Bookcase Towers by aligning the holes on the side panels. Insert Sleeve
Nuts (H) on the inside of the Bridge (A) and Bolts (I) on the inside of the Bookcase Towers. Tighten with 2
pcs Allen Keys (F) as shown below.
4.
5. Insert bolts (C), Spring Washer (D), Metal Washer (E) into holes Metal Bracket (G). Tighten with Allen Key
(F), as shown below.
A
A
I
H
F
A
G
C
D
E
F
A

www.pbteen.com Page 5 of 6
6. Attach Metal Bracket to the Top Panel Tower Bookcase, by inserting bolt, Lock Washer, Metal Washer into
hole. Tighten with Allen Key as shown below.
Note:
For safe mounting it is essential to use the proper hardware for your wall type. The hardware included is
meant for drywall or wood stud mounting only. If walls are concrete, brick or plaster, please consult your
local hardware store for assistance. Mount to wood studs whenever possible.
7. Drywall Mounting:
Place the bookcase with the Metal Bracket (J)
attached, against the wall in its desired loaction.
Using a pencil, mark the wall through the hole of
Metal Bracket (E). These marks on the wall will be
your insertion points for the mounting hardware.
Remove the Metal Bracket from the top of the
bookcase using the Allen Key. With a Philip's head
screwdriver; insert the Drywall Anchors (E) through
the pencil marks of your insertion points. Gently
press the anchor while turning it in a clockwise
direction until anchor’s head is flush with the wall.
Repeat for any other insertion points located over
drywall. Re-attach the Metal bracket to the top of
the bookcase. Using a Philip's head screwdriver,
align the slots in the Metal Brackets (J) to the hole
in the Drywall Anchors (E). Insert Screws (F) and
Metal Washer (K), through the slots in the Metal
Brackets (J), and into the holes of the Drywall
Anchors (E). Make sure the Tower Bookcase is
securely fastened to the wall.
Note: The Tower Bookcase can be adjusted in and out, and up and down (slightly) by loosening the
bolt/screws, making your adjustment, and securely. Re-tightening all bolts and screws.
WALL
E
E
J
WALL
F
K