PB TEEN Lilac Chiffonier User manual

Lilac Chiffonier
CAUTION
The top shelf of this cart/stand is intended for use only with Tube televisions having a maximum screen
size of 32 inches and weight of 135 lbs.
All other support shelves should not be loaded more than 25 lbs.
DO NOT EXCEED RECOMMENDED LOAD. Use with products heavier than the maximum sizes and
weights indicated may result in instability, causing possible injury.
This unit contains a permanent sticker located either beneath top shelf or inside drawer.
Do not allow children under 16 years to move cart.
Pre-assembly:
Please read all instructions before beginning assembly.
Two adult assembly is recommended.
Save all packing materials until assembly is complete to avoid accidentally discarding smaller parts or
hardware.
An extra wooden knob is included for your convenience.
Parts included :
A – Top Unit – 1pc B – Base Unit – 1pc C - Adjustable shelf – 1pc
www.pbteen.com

Hardware included:
D – Wooden Knob (big) – 8pcs E - Wooden Knob(small) – 2pcs F – Long Wood Knob Screw
(32*4mm)–2pcs
www.pbteen.com
G – Medium Wood Knob Screw H – Short Wood Knob Screw
(25*4mm) – 2pcs (22*4mm) – 6pcs
I - Shelf Support Pegs – 8 pcs
(4 to be used with optional shelf; 4 spare pegs) J – Mending Plates – 2pcs
K - Long Phillips Head Screw – 8pcs
Tools required:
Phillips Head Screwdriver (not included)
Assembly:
1. On a soft, scratch-free surface, such as a carpet or rug, remove the Top Unit (A) from box.
2. Determine the desired height for Shelf (C) using the corresponding peg holes on the interior sides
of the Top Unit (A).
3. Insert the Shelf Support Pegs (I) into the pre-drilled holes until fully secure. Place Shelf (C) onto
the Shelf Support Pegs (I) making sure the Shelf (C) is stable, as shown.
I

4. Gently attach Small Wooden Knobs (E) to interior drawers. Hold Small Wooden Knobs (E) over
pre-drilled hole in drawer front. Screw Long Wooden Knob Bolt (F) through the rear of the drawer
so that it enters the Small Wooden Knob (E). Tighten using Phillips Head Screwdriver, as shown.
Repeat with Big Wooden Knob (D) for the Top Unit’s doors using Medium Wood Knob Screws
(G), and the drawers of Base Unit (B), using Short Wood Knob Screws (H).
www.pbteen.com
5. With two adults, lift up the Top Unit (A) and slowly lower it, until it sits on the top of the Base Unit
(B). Align Top Unit (A) and Base Unit (B) center to center. Place the Mending Plate (J) over the pre-
drilled holes in the back of the Base Unit (B) and the back of the Top Unit (A), as shown below.
6. Using a Phillips Head Screwdriver, insert the Phillips Head Screws (K) through the lower pre-drilled
holes of the Mending Plate (J) and into the pre-drilled holes at the back of Base Unit (B) and loosely
tighten. Insert Phillips Head Screw (K) through the upper pre-drilled holes of the Mending Plate (J) and
into the pre-drilled holes of the Top Unit (A) and loosely tighten. Once all screws are in place, fully
tighten. Adjust recessed levelers at the bottom of legs to make sure the whole assembly is balanced.
7. Hardware should be checked periodically for tightness.
Care Instructions:
• Avoid direct sunlight and excessive
temperatures.
• Dust often using a clean, soft, dry and
lint-free cloth.
• Slightly moisten cloth with water. A
damp cloth holds dust and prevents
scratching.
• Waxing is not recommended on
lacquered finish.
E
D
D
H
G
F
E
J
K

Furniture Tipping Restraint
Young children may be injured by tipping furniture. The use of a tipping restraint is highly recommended.
When properly installed, this restraint could provide protection against the unexpected tipping of furniture
due to small tremors, bumping or climbing. We recommend mounting this restraint to a wall stud.
WARNING: This product is only a deterrent. It is not a substitute for proper adult supervision.
Hardware Included:
www.pbteen.com
A - (2) Brackets B - (2) Long screws (6 x 32mm)
C - (2) Short screws (6 x 20mm) D - (1) Nylon strap
Installation Instructions:
1. Locate a wall stud behind your furniture. Position a Bracket (A) on the stud approximately 1”
below the top of the furniture. Mark and drill pilot hole into the center of the stud with a 3/32” drill
bit. Attach a Bracket (A) to the stud with the Long Screws (B) provided.
2. On the back of the furniture, the second Bracket (A) will need to be attached to the furniture frame
at the top.To do this, temporarily move the furniture into its final position and mark the location of
the wall’s Bracket (A) on the furniture frame with a pencil.
3. Move the furniture away from the wall and place a Bracket (A) on the mark. Using the marks from
the previous step as a guide, drill holes for screws with a 3/32” drill bit. Attach the bracket to the
furniture with the Short Screws (C) provided.
4. Move the furniture into its final position, taking care to line up the wall bracket with the furniture
bracket. Thread the Nylon Strap (D) through the Bracket and clinch as shown in the illustration.
Tighten strap until snug. Do not overtighten.