PB TEEN HAMPTON User manual

Date: 2013-Aug.-05
Rev: www.pbteen.com Page 1 of 4
HAMPTON STORAGE BED
ASSEMBLY INSTRUCTION

Date: 2013-Aug.-05
Rev: www.pbteen.com Page 2 of 4
Important safety instructions:
•Please read all all instruction carefully before assembling this desk.
•For your safety, assembly by two or more adults is strongly recommended.
•Keep these instructions for future use.
•Use only vendor-supplied hardware to assembly this item. Using unauthorized hardware could jeopardize
the structural integrity of the item.
Pre- assembly:
•Remove all parts and hardware from the box and place them on a carpeted or scratch-free work
surface. The shipping box provides an ideal work surface.
•To avoid accidentally discarding small parts or hardware, please do not dispose of any contents until
assembly is complete.
•Two people are recommended for your safety and ease of assembly.
•Prior to starting the assembly, use the parts and hardware lists to identify and separate each of the
pieces included.
•The illustrations provided allow for easier assembly when used in conjunction with the assembly
instructions.
•Note: Do not fully tighten any of the bolts until all parts are in place. Failure to follow these instructions
may cause the bolts to misalign during assembly.
•Please use caution if using power tools to aid in assembly. Power tools can damage the hardware or
split the wood.
Parts included:
A – Headboard – 1 pc
B – Footboard – 1 pc
C – Siderail Box – 2 pcs
D – Center Panel – 4 pcs
E – Support Leg – 2 pc
Hardware included:
F – Long Hex Bolt G – Short Hex Bolt H – Spring Washer I – Flat Washer J – Phillip headscrew
5/16”x38x15 (mm)
1/4”x19x15 (mm) 5/16”x13x2 (mm) 5/16”x15x2 (mm) 8 x 30 (mm)
12pcs 8pcs 20pcs 20pcs 24pcs
K – Wooden Dowel L – Allen Key M – Leveler N – Wooden Block
10 x 30 (mm) (Included)
3/8”x85x50x35x3
(mm)
76 x76 x18 (mm)
8pcs 1pc 4pcs 4pcs
TOOLS REQUIRED (but not included): Phillip Head Screwdriver

Date: 2013-Aug.-05
Rev: www.pbteen.com Page 3 of 4
Assembly Instruction Steps:
1. Lay the Siderail Box (C) upside down on a soft, scratch-free surface.
2. Attach the Levelers (M) to the bottom of the Siderail Box (C) using a Spring Washer (H), Flat Washer (I)
and a Short Hex Bolt (G), insert through the pre-drilled holes on the Leveler (M) and into the pre-drilled
hole on the bottom of the Siderail Box (C) as shown below; tighten using the Allen Key (L).
3. Attach the Support Leg (E) to the center bottom of the Siderail Box (C) by screwing the Support Leg (E)
with bolt pre-attached into the pre-drilled holes on center bottom of the Siderail Box (C) as shown below.
4. Repeat Steps1-3 for the other Siderail Box (C).
5. Turn Siderail Boxes (C) upright. Place the Wooden Blocks (N) under the Siderail Boxes for support with
leveling as shown below. Adjust Levelers (M) until they sit level with the Support Leg (E). Align the Siderail
Boxes (C) so they are parallel and remove Wooden Blocks (N).
6. Insert one end of the Wooden Dowels (K) into the pre-drilled holes on the headboard end of the Siderail
Box (C) and the other end into the corresponding holes in the legs of the Headboard (A). Insert a Spring
Washer (H), Flat Washer (I) and Long Hex Bolt (F) through the other pre-drilled holes of the Siderail Box
(C) into the pre-drilled holes in the leg of the Headboard (A) as shown below. Do not fully tighten the Long
Hex Bolt (F) until all are in place to avoid misalignment; tighten with the Allen Key (L). Repeat for the
Footboard (B).
7. Adjust the recessed levelers located at the base of each leg and underneath both Siderail Box (C) by
turning counter-wise until level.
Figure 1
Figure 2

Date: 2013-Aug.-05
Rev: www.pbteen.com Page 4 of 4
8. Lay the Center Panels (D) over the inner groves on both Siderail Boxes (C) as shown below. Insert Phillips
Head Screws (J) in the pre-drilled holes; tighten using a Phillips Head Screwdriver.
Care Instructions:
•Dust often using a clean, soft, dry and lint-free cloth.
•Blot spills immediately and wipe with a clean, damp, cloth.
•We do not recommend the use of chemical cleansers, abrasives or furniture polish on our lacquered
finish.
•Hardware may loosen over time. Periodically check to make sure all connections are tight.
Re-tighten if necessary.
Figure 3